Aircat 6300 User manual

MODEL: 6300
6” PALM GRIP SANDER

SPECIFICATIONS
Important Warnings - Sanders & Polishers
1. Eye protection, safety gloves and safety aprons must always we worn when operating a sander or
polisher.
2. Never adjust the sander or polisher or change the backing pad, sanding disc, sanding belt or
polishing bonnet unless the air supply and air hose is disconnected from the tool
3. Only use backing pads and polishing backing pads that have a rated speed then same as the sander
or polisher or higher.
4. Never attempt to modify or adapt a sander or polisher for use with a grinding wheel or cut-off wheel
or wire brush.
5. Only personnel trained in the correct methods to change pads, sanding discs, sanding belts and
polishing bonnets should conduct these operations.
Model No. Free Speed
(RPM)
Pad Size
(in.)
Spindle Thread
(in.)
Orbit
(in.)
Weight
(lbs.)
Length
(in)
Air Cons.
(CFM)
Rec. Hose
Size
(in.)
Air Inlet
(in.)
6300 11,000 6 5/16 - 24 3/16 1.75 7.0 2.5 3/8 1/4 NPT
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule.The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 1/4”NPT American Thread. Line pressure should be increased to compensate for
unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8”I.D. and ttings should have the same inside dimensions.
Air Supply

MODEL: 6300
6” PALM GRIP SANDER
Exploded View & Parts List
Reference
Number
Part Number Description Reference
Number
Part Number Description
1 9OB-03 Snap Ring 23 9OB86823A O-Ring
2 9OB-04 O-Ring 24 981326 Pin
3 9ST316003 Valve Stem 25 9STOB-25 Front Plate
4 9OB-02 O-Ring (2) 26 9OB-26A Bearing
5 9ST316005 Regulator 27 9OB-28.1 Washer
6 9OB-06 Washer 27A 9OB-28 Washer
7 9STOB-08 Valve 28 9E-29 Washer
8 9OB-09-2 Spring 29 9ST70407 Key
9 970426 Air Inlet 30 9STS560-29 Motor Shaft Balancer
10 9SX-11.1 Stainless Mesh 31 9OB-30 Snap Ring
11 9SX-11 Silencer 33 9OB-33 Snap Ring
12 9ST246011 Sleeve 34 9S560-34 Shaft
13 9OB86811-1 Lever (Black) 35 9ST246034 O-Ring
14 9OB86814 Pin 36 9RS0134 Lock Nut
15 9OB86813-3 Housing (AIRCAT) 37 9ST2460N36 Shroud
16 970410 Retaining Ring 38 5437 PSA Pad (AIRCAT)
17 970048A Bearing
18 9STOB-19 Rear Plate
42 9OB-39-22 Stop Spanner
19 9OB-20 Rotor Blade (5)
45 9OB-101-32A Bearing
20 9STOB-21 Rotor
21 9ST246021A Cylinder
48 9OB86848 Rubber Washer
22 9OB-23 Pin

SERVICE CENTER LISTINGS ENCLOSED