aireRyder F0063 User manual

Model No.: F0063 / F0064 / F0065
aireRyder ORIGINAL CEILING FAN LIMITED LIFETIME WARRANTY
The limited lifetime warranty covers this ceiling fan, for residential use by the original purchaser, against defects in
material or workmanship as follows:
If your aireRyder Ceiling Fan motor fails at any time during the lifetime of the original purchaser due to defects in
material or workmanship, we will provide a replacement part free of charge.
If your Fan motor fails at any time within one year after the original date of sale to the original purchaser due to defects
in material or workmanship, we will provide labor to repair the defect, with the exception of take down/reinstallation,
free of charge. The original purchaser will be responsible for all labor costs after this one year period.
If no replacement parts are provided for any part of your Fan motor that fails at any time during your lifetime due to
defects in material or workmanship, we will refund the original purchase price of your Fan.
If your Fan blades, reverse switch, or any accessory, except glass globes and light bulbs, fails at any
time within one year after the original date of purchase due to a defect in material and workmanship, we will repair or, if
we choose, replace the defective blades, switch, or accessory free of charge, with the exception of take
down/reinstallation services.
If the original purchaser ceases to own the Fan, this warranty and any implied warranty, including but not limited to any
implied warranty of merchantability or fitness for a particular purpose, become void. This warranty and any implied
warranty, including but not limited to any implied warranty of merchantability or fitness for a particular purpose, do not
cover glass globes, light bulbs, or finish on any metal portions of the Fan.
This warranty is in lieu of express warranties. The duration of any implied warranty of merchantability or fitness for a
particular purpose, with respect to any aireRyder Ceiling Fan motor, blades, switch, or accessories, is expressly
limited to the period of the express warranty set forth above for such motor, blades, switch, or accessories.
This warranty excludes defects, malfunctions, or failures of any aireRyder Ceiling Fan that are caused by repairs by
persons not authorized by us, use of parts or accessories not authorized by us, mishandling, improper installation,
modifications or damage to the Fan while in your possession, or unreasonable use, including failure to provide
necessary maintenance.
In no event shall aireRyder Fan be liable for consequential or incidental damages.
Some states do not allow the exclusion or limitation of consequential or incidental damages, in which case the above
limitation or exclusion may not apply.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
LIMITED LIFETIME WARRANTY
PAGE: 1 / 8 181008
F A N C O

Unpack your fan and check the contents. You should have the following items.
1.) Mounting plate
2.) Fan Fixture Set
3.) Fan Light
4.) Glass Shade
5.) Fan Blade (3 PCS)
6.) Assembly Kit
7.) 1-22W Built-in LED Module Included.
8.) Installation Instructions
Package Contents:
Dimension Reference:
A. 13˝ B. 10-1/4˝ C. 44˝ D. 8˝
Installation Instructions
1
2
3
4
6
5
7
8
181008
F A N C O
PAGE: 2 / 8

Exploded View Detail
Mounting Plate
Fan Fixture Set
Fan Blade
F A N C O
181008
Glass Shade
Fan Light
PAGE: 3 / 8
LED Module

Safety Instructions
READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN
INSTALLING THE FAN AND SAVE INSTRUCTIONS.
All set screws of the fan must be checked and retightened where necessary before installation.
To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets,
balancing the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.
Before changing the fan direction, turn off the fan and wait for the fan blades to stop completely.
If a stationary appliance is not provided with a supply cord and a plug, or with other means for
disconnection from the mains supply having a contact separation of at least 3 mm in all poles, that
means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
NOTE: The safeguards provided by these safety instructions and by the separate installation
instructions are not meant to cover all possible conditions and situations that may occur. It must be
understood that common sense, caution and care are factors which can not be built into this product.
These factors must be supplied by the person(s) installing, caring for and operating the fan.
TO AVOID RISK OF ELECTRIC SHOCK, BE SURE TO SHUT OFF POWER AT THE MAIN
FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS
FIXTURE. TURNING OFF THE ELECTRICAL POWER BY USING THE LIGHT SWITCH
IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
TO REDUCE THE RISK OF INJURY, INSTALL THE FAN SO THAT THE BLADES ARE
AT LEAST 7 FEET (2.1 METERS) ABOVE THE FLOOR AND AT LEAST 18 INCHES
(0.5 METERS) FROM THE TIP OF THE BLADES TO THE WALL.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT
TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT" AND USE MOUNTING
SCREWS PROVIDED WITH THE OUTLET BOX.
THE INSTALLATION HAS TO BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL
CODE, ANSI/NFPA 70-1999 AND LOCAL CODES. IF YOU ARE UNFAMILIAR WITH THE
METHODS OF INSTALLING ELECTRICAL WIRING, SEEK THE SERVICES OF A
QUALIFIED LICENSED ELECTRICIAN.
WARNING
F A N C O
181008
PAGE: 4 / 8
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DON’T USE THIS FAN WITH
ANY SOLID-STATE SPEED CONTROL DEVICE.

Installation Steps :
Fig.1
Turn OFF the electric power at the
main fuse or circuit breaker box.
Left fan fixture set and hang on
mounting plate with hook provided,
through one of the two holes in
canopy. This will allow for
hands-free wiring.
CAUTION: Use only a side with
hole in canopy, not hook slot.
F A N C O
181008
PAGE: 5 / 8
INSTALLATION INSTRUCTIONS
NOTE: The fan weight is 35lbs (15.9kg). Be sure the outlet box you are using is securely attached to the building
structure and can support the full weight of the fan. Failure to do so can result in serious injury.
Fig.4
Fig.5
Fig.7
Hang the safety cable into the
safety cable hook.
IMPORTANT:
BEFORE YOU BEGIN INSTALLING THE FAN, CAREFULLY READ ALL INFORMATION ON THE SEPARATE
SHEET "SAFETY INSTRUCTIONS" AS WELL AS THE FOLLOWING "INSTALLATION INSTRUCTIONS". IF IN
DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
SAVE ALL INSTRUCTIONS.
Fig.6
Twist wire ends together and
screw wire connectors on
in a clockwise direction. tape wire
connectors and wire together.
instructions that the splics after being
made should be turned upward and
pushed carefully up into the outlet box.
Screw the safety cable hook to the ceiling outlet box. Insert wires from the
outlet box through the hole in center of mounting plate. Attach the mounting
plate to the outlet box by using two flat washers and mounting screws.
WARNING: MOUNT ONLY TO AN OUTLET BOX MARKED " ACCEPTABLE FOR
FAN SUPPORT OF 15.9KG(35LBS) OR LESS"!
Mounting Plate
Outlet Box
Flat Washer
Mounting Screw
Fig.3
.
Fig.2
Safety Cable Hook
Ceiling
Mounting Plate
Fan Fixture Set
Wire Connector
Fan Fixture Set
Make wire connections:
1).The white motor wire to the white
wire from the outlet box with a wire
connector.
2).The black motor wire to the black
wire from the outlet box with a wire
connector.
3). The ground wire from the outlet box
to the ground wire from the mounting
plate with a wire connector.
Safety cable

PAGE: 6 / 8
Screw
Canopy
Position both slots on the canopy directly
under and in line with two screws and
lock washers in the mounting plate. Lift
the canopy, allowing the two screws and
lock washers to slide into the mating slots.
Rotate the canopy counterclockwise until
both screws from the mounting plate drop
into the slot recesses. Tighten screws
securely. Install the other two screws and
lock washers into the mating holes of the
mounting plate and tighten to secure the
canopy to the mounting plate.
Insert the fan blade through the slot
on the fan fixture set.
and fasten fan blade to the fan
fixture set with screws. Repeat for
remaining fan blades.
F A N C O
181008
Fig.8
Mounting Plate
Lock Washer
Fan Blade
Fan Fixture Set
Blade Screw
Fig.9
Turn ON the electric power at the
main fuse or circuit breaker box.
Fig.13
Fig.12
Install the glass shade by screwing it
onto the central fan fixture. (Make sure
the glass shade is securely attached,
but DO NOT over tighten.)
Fan Light Installation:
WARNING:
As per EPACT 2005 requirements, this fan light has a built-in current limiting device in the receiver of remote control to
conserve energy. The fan light will not be brighter when you press dimmer button if the combined wattage of the
installed bulbs exceeds 190 Watts.
Install Fan Light . Make wire connection. Plug the male
connector from the motor into the female
connector from the LED Module .
Carefully put the wires into the switch box.
Secure the LED Module up to the bottom
of the motor with LED Module screws.
Fig.10 Fig.11
Male Connector
Female Connector
LED Module Screw
LED Module
Fan Light

PAGE: 7 / 8
F A N C O
181008
Fig.14
SET
123 4
ON
D
Remote control
Install one 12 volt battery (type 23AE included) to the remote control.
Buttons:
1- Fan speed control: controls the ceiling fan speed (I for the lowest speed, VI for the
fastest speed)
2- Fan OFF: turns the fan off
3- Reverse function: controls fan direction
4- Lighting control: adjusts the intensity of the light (if applicable, depending on bulb).
5- CODE setting: using method as below
Step 1: Finish the installation of the ceiling fan.
Step 2: Turn the power on for the ceiling fan and within 60 seconds, press and hold
SET button on back of remote control for 5 seconds. The light of the ceiling fan
flashes twice when setup is completed.
Step 3: After setup is completed, switch to the desired speed. The fan will run
on the
highest and lowest speed first, and will then turn to the selected speed
automatically.
1
2
3
45
6
6- Light setting: selects On/Off or Dimming function for light
<D> On/Off function without dimming (required for energy saving lamps [CFL]).
<ON> Dimming function enabled (for tungsten lamps; not compatible with energy saving lamps [CFL]).
Note: After changing the blades, the CODE setting has to be performed again.
Note: The receiver provides protection in the following two situations:
1- Lock protection: The receiver has a built-in protection against obstruction during operation. The motor will be locked and the
power will be disconnected after 30 seconds of obstruction. Please remove obstacles before restarting. To reset, turn off the
power supply to the fan motor, then restart.
2- Power surge protection: If the receiver detects a power consumption of the motor greater than 80W, the power supply will be
interrupted and operation will immediately stop. To reset, turn off the power supply to the fan
motor, then restart (after 5 seconds).

Trouble Shooting Guide
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation
or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,
please check this Trouble Shooting Guide. If a problem cannot be remedied or you are experiencing difficulty
in installation, please call our Customer Service Department.
PROBLEM
1. If fan does not start:
2. If fan sounds noisy:
3. If fan wobbles:
4. If light does not work:
1. Check main and branch circuit fuses or circuit breakers.
2. Check line wire connections to fan and switch wire connections in switch
housing.
CAUTION: Make sure main power is turned off.
3. Make sure forward/reverse switch is firmly in left or right position. Fan will not
operate when switch is in the middle.
4. Make sure that the wall control is turned "ON".
1. Make sure all screws in motor housing are snug. (not over tightened)
2. Make sure the screws which attach the fan bladeholder to the motor are tight.
3. Make sure wire connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4. If using an optional ceiling fan light kit, check to be sure the screws securing
the glassware are finger tight. Check to be sure light bulb is tight in socket and
not touching glass shade(s). If vibration persists from glass, remove glass and
install a 1/4 in. wide rubber band on glass neck to act as an insulator. Replace
glass and tighten screws against rubber band.
5. Some fan motors are sensitive to signals from Solid State variable speed
controls. DO NOT USE a Solid State variable speed control.
6. Allow "break-in" period of 24 hours. Most noises associated with a new fan will
disappear after this period.
All blades are weighed and grouped by weight. Natural woods vary in density
which could cause the fan to wobble even though all blades are weight-matched.
The following procedures should eliminate most of the wobble. Check for wobble
after each step.
1. Check that all blades are screwed firmly into blade holders.
2. Check that all blade holders are tightened securely to motor.
3. Make sure that canopy and mounting bracket are tightened securely to ceiling
junction box and junction box is mounted firmly to ceiling joist.
4. Most fan wobble problems are caused when blades are not equally level. To
check the blade levels, select a point on the ceiling above the tip of any blade.
Measure the distance from the ceiling to the blade tip, to an accuracy of 1/8
inch. Rotate the blades until the next blade is in the measuring position. Repeat
measurement for each blade. If all blade levels are not equal, you can adjust
blade levels by the following procedure. To adjust a blade tip down, insert a
washer (not supplied) between the blade and blade holder at the screw
closest to the motor. To adjust a blade tip up, insert washer (not supplied)
between the blade and blade holder at the two screws farthest from the motor.
5. If blade wobble is still noticeable, interchanging two adjacent (side by side)
blades can redistribute the weight and possibly result in smoother operation.
1. Check blue wire from fan to make sure it is connected to hot wire from house.
2. Check for loose or disconnected wires in fan switch housing.
3. Check for loose or disconnected wires in light kit.
4. Check for faulty light bulbs.
CAUTION: Make sure main power is turned off before entering switch housing.
SUGGESTED REMEDY
PAGE: 8 / 8 181008
F A N C O