Airistar 100GT User manual

Airistar® 100GT Owner’s Manual ©2007
Airistar®100GT Air Purifier

Check power switches. Both the green on-off switch and the
speed control knob must be in the on position.
Check that the unit is connected to the power source.
Check electrical outlet or circuit breakers.
Ensure that the air duct connects the blower unit and the
diffuser.
Contact your distributor or Airistar customer service.
Check if filters need replacing.
Check for items blocking the air intake grid.
Check for occlusions or kinks in the air duct connected to the
diffuser.
Check if diffuser controls are set for maximum airflow.
Unit has reduced airflow:
16
100 GT
09/07 SPB

Describes troubleshooting procedures for the Airistar®100GT
Filter Replacement
Filter Replacement Notes
1
4
5
6
9
10
10
11
12
15
15

100GT
Pre-filter
within your gaming establishment.
Melt-Blown
Fiber Filter
Activated
Carbon Filter
1 14

Three Stage Purification Process:
Melt-Blown Fiber Filter (MBF) - Rated up to 95% @ 0.3 microns
Your new air purification unit utilizes the three stages shown above to strip
away smaller and smaller particles from the air, creating compounding
efficiency. The front of the diffuser directs the clean air at a 50 degree
angle towards the patrons to provide an air curtain between smoking
patrons and the employee, while the air from the rear of the diffuser is
directed straight up to provide the employee with purified air.
Electrostatic Pre-filter - MERV 8
Activated Carbon Filter - Odor and Gas control
Pre-filter Melt-Blown
Fiber Filter
Activated
Carbon Filter
E
D
AB C
G
F
H
A- Electrostatic Pre-filter
B- Melt-Blown Fiber Filter
C- Activated Carbon Filter
D- Filter Frame
E- Blower Unit
F- Control Panel
G- Connection Tubing
H- Diffuser
213

Melt-Blown Fiber
Filter Media
Melt-Blown Fiber filter media is the next
generation of HEPA filter media. The Melt-
Blown Fiber filter media used in the Airistar
®
100GT is rated to
capture 95% of particles larger than 0.3 microns at airflow ratios that
surpass traditional HEPA filters.
Activated Carbon
VOC Filter
VOC’s are gases and odors that are emitted
from certain solid and liquid compounds.
Airistar’s multipurpose VOC filter helps eliminate unwanted
gases and fumes associated with tobacco products.
MERV 8 Pre-filter
Our pre-filter is MERV 8 pleated media. It is
designed to remove larger airborne particles in the range of
3-10 microns in size or larger. This would include substances such
as certain types of bacteria, mold and plant spores, as well as lung
damaging dust. By extracting these larger particles first; this allows
the two remaining filters to collect smaller particulate at a more
efficient rate.
Pre-filter Melt-Blown
Fiber Filter
Activated
Carbon Filter
123

Filter Replacement
1) To remove filters, remove the filter box from the purification
unit then remove filters from filter frame.
From left to right: Filter frame, Pre-filter (Green),
Melt-blown Fiber Filter (Yellow), and
Activated Carbon Filter (Red).
1) Follow color coding and directional arrows.
The pre-filter (Green) goes first with the arrow pointing
inside the filter frame. The Melt-Blown Fiber Filter (Yellow)
installs second, again with the arrow pointing inside the filter
frame. Finally, the Activated Carbon Filter (Red) goes into
the filter frame with the arrow pointing inside the filter frame.
2) Place the filter frame into the purification unit with the arrow
pointing to the left.
3) Close door and power up.
Always securely mount the unit.
11 4

Airistar®100GT Control Panel
Describes the controls for the Airistar 100GT air purifier
The Airistar 100GT includes adjustments to control the airflow.
1. Move the levers on the grill of the diffuser toward the outside to increase
airflow and toward the center to reduce airflow.
2. Toggle the green switch on the control panel to turn the blower on or off.
3. The speed control knob can be set to High (H); Low (L) or Off (O).
AF302-1
AF303-1
AF304-1
12 (Monthly)
2 (6 Months)
4 (3 Months)
12 (Monthly)
1 (Annual)
2 (6 Months)
Pre-Filter
Melt-Blown Fiber Filter(MBF)
Activated Carbon Filter
Follow the procedures below whenever you replace any of the filters.
1) Turn off the unit and disconnect it from all sources of
electrical power.
2) Allow the blower to stop fully.
3) Put gloves on for your protection.
4) Unlatch and open the filter door of the unit.
5) Pull the filter frame straight out of the unit by the handle.
6) Remove filters and place in garbage bag for disposal.
7) Place new filters in unit referring to the diagram on the
following page.
8) Place the filter frame back in the unit with the arrow
facing to your left.
9) Close and re-latch the filter door.
10) Reconnect electrical power and turn unit on.
11) Thoroughly wash / sanitize hands after proper disposal of
soiled filters.
105

Describes how to turn on and set up the Airistar® 100GT for use
he Airistar 100GT includes brackets for mounting the
blower unit to the underside of a horizontal surface
(i.e. blackjack table) and two sets of adjustable
brackets to mount the diffuser in various orientations. The
mounting methods can be adapted to the needs of your
particular installation. Please consult your sales representative
or Airistar Technologies for support with custom installations.
Information for maintaining and replacing the
filters for the Airistar® 100GT
he Airistar 100GT filters should be changed on a regular
schedule. The table on the following page lists the part
numbers of each filter and the recommended replacement
schedules for heavy-duty use environments.
,
etc.
69

Installation of the Airistar®100GT
Examine the Airistar 100GT blower, diffuser and your installation
location and plan your installation methods.
To mount the blower beneath a table with the provided brackets:
1. Determine the mounting location
a. Check that power jack and filter door are accessible.)
b. A pathway for the airduct to the diffuser will also need to
be accomodated.)
2. Use the installation template to locate and pre-drill the screw holes.
3. Install the mounting bracket to the surface.
a. Mount with the set screw end of the brackets in the direction
from which you will install the blower unit.
b. Leave the screws slightly loose for later adjustments.
4. Loosen the set screws on the mounting brackets and slide the blower
into position with the air exit nozzle oriented toward the diffuser.
a. Tighten the set screws on the mounting brackets to lock the
blower unit into position.
b. Adjust the mounting brackets slightly as necessary and tighten
the mounting screws.
Note: Other mounting locations are possible with consideration taken for the power jack,
filter door and pathway for the air duct to the diffuser.
To mount the diffuser to the table with the provided mounting brackets:
1. Determine the location and method for mounting the diffuser.
Note: There are both large and small mounting brackets provided for multiple
mounting options.
2. Use the installation template (provided in kit) to mark the cut out area
on the table.
Note: Be sure to provide clearance to accomodate the mounting brackets and screws.
3. Check the fit of the diffuser and brackets into the cut out and determine
the cut length of the air duct hose.
4. Cut the air duct hose to length.
(The nozzles on the blower and diffuser require approximately a +/- 1/2” tolerance.)
5. Install the air duct hose to the blower and diffuser. Preload but do not
tighten the adjustable band clamps.
6. Place the diffuser into position and adjust the mounting brackets to the
proper position for your installation.
7. Mark the locations for the mounting screws and drill pilot holes.
(Adjust the mounting brackets for the desired positioning.)
8. Install the mounting screws and complete final adjustments.
Note: It the diffuser will be mounted through a table (full perimeter cut-out) the face plate
will have to be removed with a security screw driver (spanner) and re-installed after
the diffuser is mounted through the table. Call your sales representative or
Airistar Customer Service if you have any questions about custom mounting.
87