Airius PureAir Series Owner's manual

AIRFLOW REINVENTED
PUREAIR SERIES
INSTALLATION,
OPERATION &
MAINTENANCE

CONTENTS
»Introducon
»Safety Precauons
»Pre-Installaon
»Installaon
»Operaon
»Maintenance
»Troubleshoong
»Warranty
Airius, LLC (Manufacturer)
811 South Sherman St.
Longmont, Colorado 80501 - USA
Toll free: 1-888-247-7327
Telephone: [phone]
Fax: [phone]
Email: inf[email protected]
Web: www.airiusfans.com
May be covered by one or more of the following
United States Patents:7,381,129 B2; D514688
and other patents pending
AIRIUS®, AIR PEAR®, AIRIUS PUREAIR®,
PEARLINK®, and THE THERMAL EQUALIZER®
are trademarks of Airius, LLC, registered in
the U.S. and in some countries abroad. Other
trademarks pending in the U.S. and abroad.
NOTE: Carefully check fans/controls for shipping
damage. Report any damage to the carrier
immediately. Do not aempt to operate if visible
damage is evident to either the circuit or to the
electronic components. All informaon contained
in this manual is intended to be correct, however
informaon and data in this manual are subject to
change without noce. Airius makes no warranty
of any kind with regard to this informaon or
data. Further, Airius is not responsible for any
omissions or errors or consequenal damage
caused by the user of the product. Airius reserves
the right to make manufacturing changes that
may not be included in this manual.
PureAir Installaon Guide: V1.3
©2023 Airius, LLC.
Introducon
Congratulaons on the purchase of Airius’
PureAir system. Our patented, American-made,
air-mixing system will ensure ion distribuon
throughout the space while driving down
expensive energy bills. We are here to support
you and if you have any quesons or comments,
we can be contacted through our website,
airiusfans.com, or give us a call: 1-888-247-7327.
About the Airius PureAir Series
Airius PureAir fans defeat pathogens, bacteria,
molds, and even odors using patented Needle
Point Bipolar Ionizaon (NPBI™) which constantly
cleans the air of unwanted organisms and odors.
Ionized air has been proven to make organisms
inacve and remove odors by pung an electrical
charge to the air molecules. These charged air
molecules will bind to organisms and disrupt
the pathogens’ surface proteins, rendering them
inacve and unable to replicate leaving only clean
air for you to breathe.
And ionized air can eliminate odors too by
breaking down chemical, pet, cooking, and
other odors into basic harmless compounds,
leaving indoor air smelling fresh and substanally
reducing odor-causing Volale Organic
Compounds (VOCs).
* THE PERFORMANCE AND RESULTS OF THE
PUREAIR SYSTEM ARE SUBJECT TO MANY
VARIABLES SUCH AS, BUT NOT LIMITED TO,
AIRFLOW OBSTRUCTIONS, THE INTERIOR
ENVIRONMENT, EXTERIOR ENVIRONMENT,
CONDITION OF BUILDING STRUCTURE, HVAC
SYSTEM PERFORMANCE AND/OR ELECTRICAL
SERVICE AND THUS, ACTUAL RESULTS MAY
VARY.
What’s In the Box
Each unit will arrive in its own box, fully
assembled. NOTE: 120VAC versions come with
a three-prong plug, and other voltages have no
plug supplied. You will need to have a qualied
electrician either wire the desired plug on to the
power cord or hard wire directly to the power
circuit. We recommend using a plug for easy
removal during maintenance.

Safety Precauons - Read &
Save
Warning! - To prevent re, electrical shock or
injury, please observe the following:
Electrical work must be performed by a qualied
person(s) in accordance with all naonal and local
codes/standards.
Airius PureAir® fans All Models
120V Models:
Supplied with a polarized/grounded plug molded
to a 6 . (1.8 m) cord. To reduce the risk of
electrical shock, this plug is intended to t in a
polarized/grounded outlet only one way. If the
plug does not t fully in the outlet, contact a
qualied electrician. Do not aempt to defeat
this safety feature.
230V & 277V Models:
Supplied with a 6  (1.8 m) cord with a 3-wire
pigtail for aachment to a single phase plug rated
for the correct voltage; NEMA type: L6-20P or
similar, wire color code: UL/CSA: black-live/
white-neutral/green-yellow-earth.
Warning! To prevent electrical shock and/or
injury, unplug/disconnect unit from power source
before you move unit, service unit or remove any
part of housing.
Warning! To reduce the risk of re or electrical
shock, do not use models 10, 15 and 25 equipped
with shaded pole motors or models 45, 60
and 100 with permanent split capacitor (PSC)
motors with any unapproved solid-state speed
control device. Models 45, 60, 100 and 125 with
electrically commutated motors (labeled as EC
or EL) are capable of variable speeds with the
proper controls. Contact Airius for addional
informaon regarding variable speed controls and
opons.
Do not carry the PureAir Series unit by the cord.
Do not use the cord as a handle. Do not use the
cord to aach or hang the product. Be sure to
grasp the plug, not the cord, when disconnecng
this unit from an electrical outlet.
Do not use this product if it has a damaged
cord, faulty plug or any broken housing or motor
component. If the supply cord, plug, motor
or housing is damaged, it must be serviced or
replaced by Airius, its service agents or similarly
qualied persons to avoid a hazard.
To prevent damage, which may result in re or
shock hazard, do not expose this product to rain
or direct moisture. Do not immerse product
into water or allow water to drip into the motor
housing. Do not install outdoors or in an area
open to the weather. Shut o power to a wet
motor at source before servicing.
Spinning blades may inict eye or other physical
injury. Always replace a damaged blade.
Disconnect unit from power source rst. Contact
Airius for replacement blades. Plasc blades are
rated 5VA, the highest re-resistant rang for
plascs, and they will not maintain a ame.
Cauon! Some PureAir products have an
unguarded impeller/fan blade. Do not use in
locaons readily accessible to people or animals.
Blades may inict injury when moving or
staonary.
To reduce the risk of injury to persons, install
product so that boom of moving fan blade or
the lowest moving part is at least 8.2 . (2.5 m)
above the oor or grade level.
The motor is thermally protected; overheang
will cause the motor to stop operang. The
motor may restart once normal operang
temperatures are achieved. If motor fails to
restart, disconnect motor from electric source
and contact Airius. Do not disable this safety
device or override this safety feature; doing so
will void the warranty.
Do not use any PVC product (electrical tape) with
the fans. If installing a fan in an environment with
cung oils in the air (producon machine shop)
contact the factory for assistance at 303-772-
2633.
Do not posion product near furnaces, replaces,
stoves or other high temperature heat sources.
Do not posion Air Pear unit such that the
downward air column created by the Air Pear will
be directly bisected by another source of air ow,
such as from another fan or from an open supply
register. Do not posion the unit close to other
objects that will interfere with fan operaon.
Do not allow fan blades to come into contact
with objects that can lock or inhibit the rotor
operaon.
Service and installaon: No lubricaon is
required. Bearings are sealed. Bail adjustment
can be made with a T-30 Torx driver/wrench, or a
5/32” Hex wrench may be used. Other tools for
service: T-20 Torx (7/64” Hex) & T-25 Torx (1/8”
Hex) and a #2 Phillips screwdriver.

Safety Precauons Connued
The PureAir unit is designed to be used with
only the electrical voltage idened on the label
located in the nozzle and on the boom of the
motor. Connecng to any other voltage could
damage the motor and create an electrical hazard
and will void warranty. If you have a queson,
please contact the factory.
Assembling Suspended Ceiling units: See
addional instrucons for kit included with this
pamphlet or located in box containing kit.
Important: Install with hanging device or fastener
rated for a minimum of 5x the weight of the unit.
Never use zip es to hang the fan. Use care when
posioning the unit. To maximize performance,
make sure the airow is unobstructed into the
top of the unit and the downward airow is
unobstructed and allowed to reach the oor.
Cleaning: Unplug unit from power source rst to
prevent electrical shock and to avoid injuries from
spinning blades. Cauon: Staonary blades can
cause injury! You may clean the plasc housing
with a warm cloth, using mild detergent only. Do
not use petroleum products, thinners, solvents,
ammonia, alcohols or other chemicals to clean
any part of the PureAir unit.
USA & Canada – ETL le #3164849 EU - CE
For addional informaon about
Airius PureAir® fans and other products/
accessories visit:
www.airiusfans.com
*DISCLAIMER: Airius partners with Global Plasma
Soluons to use their NPBI technology. Global
Plasma Soluons (GPS) uses mulple data points
to formulate performance validaon statements.
GPS technology is used in a wide range of
applicaons across diverse environmental
condions. Since locaons will vary, clients
should evaluate their individual applicaon
and environmental condions when making an
assessment regarding the technology’s potenal
benets.
The use of this technology is not intended to take
the place of reasonable precauons to prevent
the transmission of pathogens. It is important
to comply with all applicable public health laws
and guidelines issued by federal, state, and local
governments and health authories as well as
ocial guidance published by the Centers for
Disease Control and Prevenon (CDC) (hps://
www.cdc.gov/coronavirus/2019-ncov/prevent-
geng-sick/prevenon.html), including but not
limited to social distancing, hand hygiene, cough
equee, and the use of face masks.
Pre-Installaon
Electrical
ELECTRICAL WORK MUST BE PERFORMED
BY A QUALIFIED PERSON(S) IN ACCORDANCE
WITH ALL NATIONAL AND LOCAL CODES/
STANDARDS.
Airius recommends installing a dedicated circuit
only to be used with the PureAir units. DO
NOT wire the units into the lighng circuit, as
the system will cycle on and o with the lights,
greatly reducing the system’s eecveness.
Outlets are available in many conguraons,
check with the local electrical contractor to
determine the preferred type for the facility.
Outlets should generally be mounted vercally
unless a “twist/locking” type is being used.
To conrm electrical connuity, if possible, plug
the PureAir system into an energized outlet at
oor level, similar to the outlet installed in the
ceiling, before permanently mounng the PureAir
in the ceiling. Only energize the fan aer hands/
ngers or loose clothing are removed from/
around the fan intake.
CAUTION − Make sure the fan voltage matches
the intended power supply before installing.
Connecng the fan to the wrong voltage will void
warranty.
Mechanical
A ladder, scissor li or other suitable means of
reaching the installaon point will be required.
The PureAir system is designed to hang
vercally 12-to-18 inches below the ceiling of
the facility with the discharge poinng to the
oor for maximum thermal equalizaon. NOTE:
The bail may be angled, as it is ratcheted for
special situaons where a vercal air column is
undesirable and an angled column would be more
eecve. Make sure the air column will have an
unimpeded path from the discharge to the oor.
If using the fans in a grocery aisle applicaon,
mount the fan a minimum of 3 . from the
edge of any open reach in case to minimize the
possibility of introducing air into the case.

The free-hanging units are designed to hang
vercally and freely from the ceiling on hardware
capable of supporng a minimum of ve mes
the weight of the unit. Example - 1/4” (7 mm)
diameter steel bolt is rated at a 60 lb. (27 kg.)
load.
Hardware that may be used to hang the unit
includes, but is not restricted to: hooks, chains,
cables, carabiners, bridle rings, beam clamps
and bolts. Roof structure, building construcon,
electrical outlets/service and accessibility
will dene the appropriate hardware for each
installaon.
If installing within a suspended ceiling, make sure
there are no objects (ducts, sprinklers, conduit,
etc.), for clearance purposes, directly above the
proposed locaon of installaon and relocate if
necessary.
Tools Needed
T-30 Torx Driver (5/32” Hex); other tools include
T-20 Torx (7/64” Hex); T-25 Torx (1/8” Hex);
#2 Phillips Driver. All necessary tools to install
mounng hardware (varies from installaon to
installaon)
Installaon
Power Requirements
Refer to individual product data sheets or
reference the label installed within the fan nozzle.
Branch Circuit Protecon
The PureAir fans do not include fuses for branch
circuit protecon. The branch circuit must have
a dedicated circuit breaker or similar device.
Naonal and local safety standards and electrical
codes may determine addional requirements for
installaon.
Fan Control
Refer to the installaon and operaon
instrucons for the specic fan control that was
purchased with your PureAir Fan system.
Do not use speed controls with any PureAir fan
with SP or PSC motors.
Any EC motor will be controlled by low voltage
0-10VDC. Airius oers several control interfaces
for manual, wireless, BACnet MS/TP control of
EC fans. For addional details, please reference
our website airiusfans.com
White - tachometer - 1 pulse/revoluon
Red - +10VDC
Yellow - Signal - accepts 0 to +10VDC
Blue - Common
To run an EC fan at full speed, connect the
yellow and red control wires.

Plug Wiring (230/277VAC)
120VAC cord is supplied with a molded three-
prong polarized/grounded plug. DO NOT
DEFEAT this SAFETY DEVICE or modify the plug
in any way.
230/277VAC no plug supplied. When ng
a plug always ensure that all relevant local
regulaons/electrical codes are understood and
followed with care - if in any doubt seek expert
guidance.
The power cord is a three-wire 18 AWG (or 16
AWG) 300VAC rated electrical cord UL rated
in North America (NA) as SJT or for CE/EU
compliance rated as HO5VV.
The three wires in the power cord are color-
coded to ensure proper wiring as follows:
BLACK or BROWN = HOT/ELECTRIFIED/LIVE
WHITE or BLUE = “N” NEUTRAL/RETURN PATH
GREEN or YELLOW-GREEN = GROUND/EARTH
The cord is aached to the fan motor via two
power leads with insulated 1/4” quick connects.
The cord is secured in the housing by a strain
relief and knoed inside the housing for
addional security.
Procedure for wiring the plug in a single-phase
electrical system:
Use CAUTION when wiring/aaching the plug
(Male Connector) to the PureAir Series system or
when using any electrical device.
1Plug should be rated for 230VAC or 277VAC and t properly into outlet (female connector)
being used for power.
2
To avoid electrical shock, DO NOT plug device
into energized outlet unl all exposed wires
and connecng terminals are enclosed by plug
housing. See plug manufacturer’s instrucons.
3Locate the three stripped wires on the 300VAC rated power cord aached to the
unit where the outer cord insulaon jacket has
been removed. Wires are coded as follows: black
or brown is HOT/Live (the energized conductor),
white or blue is neutral “N” (the conductor used
for a return current path) and green or yellow/
green is ground/earth (the conductor to connect
to the earth).
4Using the plug manufacturer’s instrucons, locate the proper posions to aach the
color-coded wire to the color-coded or otherwise
appropriately labeled terminals on the plug.
5
Tighten all connecons. Reassemble plug
in accordance with plug manufacturer’s
instrucons.
To conrm electrical connuity, if possible, plug
the PureAir system into an energized outlet on
the ground, similar to the outlet installed in the
ceiling, before permanently mounng.
NOTE: The PureAir System can be wired
directly to a juncon box but only by a qualied
electrician or similarly qualied person. Always
ensure that all relevant local regulaons/electrical
codes are understood and followed with care - if
in any doubt seek expert guidance. Check local
electrical codes. The preferred system is designed
with a plug for easy service and cleaning. An
on-o switch must be installed in the circuit to
be able to disable the power to prevent electrical
hazard when servicing the appliance.
Suggested Installaon Methods
Hardware that may be used to hang the unit
includes, but is not restricted to: Hooks, chains,
cables, carabiners, bridle rings, beam clamps and
bolts. Roof structure, building construcon and
accessibility will dene the appropriate hardware
for each installaon. Mount the fan as high in the
ceiling as possible and do not restrict airow into
the intake.
Aer ensuring the PureAir system is rmly
aached and aer REMOVING YOUR HANDS
FROM THE UNIT, ONLY THEN is it safe to
plug the unit into the power source using the
approved plug to conrm funcon and electrical
connuity.
NOTE: Secure the power cord to the ceiling
structure as added security. The cord will act as
a safety leash and by securing it the possibility of
the plug accidentally coming out of the outlet is
greatly reduced. A 50 lb. (20 kg.) rated Zip Tie or
several wraps of mechanics wire are examples of
methods of securing the power cord.

Suggested Installaon Methods
1Remove the PureAir from its box, then remove the plasc protecve bag. The bail (handle)
is aached via two Torx screws. Using T-30 Torx
driver, loosen these screws enough so the bail
may swing.
2
Swing the bail to the vercal posion and re-
ghten the two Torx screws.
3
The PureAir system is designed to hang
vercally and freely 12-to-18 inches,
or as close as possible, from the ceiling on
professionally installed hardware, for models
10/15/25, capable of supporng a minimum of
ve mes the weight of the Air Pear unit, 60 lb.
(27 kg.). Example - 1/4” (7 mm) diameter steel
bolt is rated at 60 lb. (27 kg.) load.
A feature of the PureAir system is its exibility.
Hardware that may be used to hang the unit
includes, but is not restricted to: Hooks, chains,
cables, carabiners, bridle rings, beam clamps and
bolts. Roof structure, building construcon and
accessibility will dene the appropriate hardware
for each installaon.

4
Aer ensuring the PureAir system is rmly
aached, remove your hands from the unit.
5
It is then safe to plug the unit into the power
source using the approved plug to conrm
funcon and electrical connuity.
6
NOTE: SECURE the power cord to the ceiling
structure as added security. The cord will act
as a safety leash and by securing it the possibility
of the plug accidentally coming out of the outlet
in the future is greatly reduced. A 50 lb. (20 kg.)
rated Zip-Tie or mechanics wire are examples of
methods of securing the power cord.
The graphic to the right is an example of hanging
the PureAir unit:

Operaon
All PureAir fans are designed to run connuously,
year-round, to maintain ion levels and air
distribuon throughout a space. The fan speed
can be maintained the same throughout the year
or varied to increase/decrease ion levels.
Maintenance
The NPBI module features a self cleaning wiper
blade that funcons every 24 hours to remove
dust build up on the carbon ber bristles.
Follow these easy steps to prevent any excess
dirt buildup and preserve the life of the product:
No lubricaon is required as bearings are sealed.
Cleaning:
Cauon: Staonary blades can cause injury!
Unplug unit from power source rst
to prevent possible electrical shock and
prevent injuries from spinning blades.
You may clean the plasc housing with
a damp cloth, using mild household
detergent only.
DO NOT use petroleum products,
thinners, solvents, ammonia, alcohols
or other chemicals to clean any part of
the PureAir unit.
Note: If fan is not operang or any parts are
broken, contact manufacturer for replacement
informaon.
Troubleshoong
The Airius products are tested before they leave
the factory, resulng in an extremely low rate of
returns. However, mechanical devices do fail, and
we recommend that you idenfy the problem and
try the simple suggesons below.
Fan will not start:
a) Check fuses and circuit breakers.
b) Check voltage at fan connecon.
c) Check speed control connecons
d) Contact manufacturer for addional
help: 1-888-247-7327.
Fan airow is too fast/slow:
a) Adjust speed control to produce
desired ow.
Fan has excess vibraon (noise or wobbles):
a) Make certain the hanging hardware
is secured ghtly.
b) Contact manufacturer for addional
help: 1-888-247-7327
I do not see a green light inside the nozzle:
a) Contact manufacturer for addional
help: 1-888-247-7327.

Airius Warranty Policy
This warranty is limited to products purchased directly from Airius, LLC (“Airius”) or one of its
authorized resellers. To determine whether a reseller is authorized, please contact Airius at the contact
informaon below. Airius warrants products listed below will operate properly and be free of defects in
materials and workmanship according to the following terms:
Products Warranty Period
PureAir Series Fans 3 Years (All Parts/Components)
Speed Controllers 1 Year (All Parts/Components)
NPBI Module 1 Years (All Parts/Components)
These include new units or units rebuilt under Airius’ factory refurbish program. Airius will repair or
replace such units, at Airius’ sole discreon, if there is any defect in their materials or workmanship
caused by Airius during the warranty period. With respect to replacement or repair rendered, Airius
warrants that the parts replaced or repaired will operate properly and be free from defects in materials
and workmanship for the remainder of the original warranty period.
Denions:
1. The “warranty period” shall begin on the shipping date from the Airius factory to the
customer (end user) .
2. “Operate properly” applies to mechanical, electrical and structural funcons only. No
guarantee is made regarding the quanty of air movement or the appropriateness
or the eecveness or merchantability of any product for its intended purpose or
for the customer’s parcular applicaon.
Exclusions:
Any of the following acons will constute a breach of and will void all warranes:
1. Improper delivery, installaon, or maintenance, including, but not limited to:
a. Failure to follow the required installaon procedures specied in the Airius “Installaon
Guide” and in all other documentaon supplied with the fans and related equipment,
including documentaon provided by the manufacturers of the individual fan and
control components;
b. Failure to follow all applicable codes and ordinances, including, but not limited to the
Naonal Electric Code and state and local building codes;
c. Failure to follow electrical engineering industry standards regarding the approved method of
installing electrical equipment having the characteriscs of the fans, the fan controls, and
their related components, even if such standards are not explicitly referenced in
any literature supplied by Airius or provided by the manufacturers of the
fan and control components.
2. Any modicaon or alteraon of, or adjustment to the fans, fan controls, and/or any
disassembly of the components of the fans and fan controls for any purpose whatsoever,
including any aempt to diagnose and/or repair any problem, without prior wrien
authorizaon from Airius. Such disassembly includes, but is not limited to, separaon of the
motor from the housing assembly and/or removal of any electrical component from the fan
controller unit.
3. Installaon of fans into a detrimental environment with airborne oils / cung uids /
solvents that may aack the base resin or motor, unless:
a. Airius has provided wrien authorizaon prior to installaon.
4. Misuse, abuse, accidents, unreasonable use or Acts of God.
5. Incorrect electric current, voltage or supply.
6. Failure to use fan controls supplied by Airius, unless:
a. Airius has provided wrien authorizaon prior to installaon; and
b. The fan controls are built, operated and maintained according to specicaons provided to
and approved by Airius.
7. Failure to perform periodic maintenance as detailed in the Airius “Installaon Guide.”

8. Consequenal or incidental damages sustained by any person or enty as a result of any
breach of these warranes are also excluded, except where such damages may not
be excluded by law.
Acquiring Warranty Service
Do not return any item without rst being assigned a Return Material Authorizaon (RMA) tag number.
Customer must obtain a RMA# from Airius (888-AIR-PEAR or inf[email protected]) before returning
the faulty unit. RMA number must appear on the return-shipping label and be associated with any
correspondence. Customer is responsible for all return shipping costs to:
Airius Warranty - RMA# ____
711 South Lincoln Street
Longmont, Colorado 80501
Airius will return the unit(s) freight prepaid. Airius may elect to repair the same unit at customer site or
oer replacement parts to facilitate repair and reduce customer down me and expense. Airius is not
responsible for misuse of their product.
Freight claims are the responsibility of the customer and all products are shipped FOB Longmont,
Colorado, USA.
Remedy and Limit of Liability
The exclusive remedy of the purchaser, and the limit of liability for Airius, for any and all losses in
connecon with this product shall be repair or replacement of the warranted product or the aected
components, as provided above.
Airius reserves the right to make the nal determinaon, based on its own assessment, as to (1) wheth-
er the problem in queson is the result of a defect in design, workmanship or materials, and not the
result of error, misuse or abuse on the part of the customer, as set forth under the exclusions detailed
above; (2) whether the problem or defect is material and requires acon under this warranty; and (3)
whether the remedy of repair or replacement is appropriate.
With regard to electrical and electronic components provided by Airius that comprise part of the prod-
ucts, including motors, Airius relies on the determinaon by the original manufacturer as to whether
the failure of such component was the result of a defect. If the manufacturer of such component
determines that there was no defect and therefore refuses to cover it under warranty, Airius likewise
will not warranty such item.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANTABILITY OR
THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY
IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. REPAIR OR
REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO
LIABILITY ON THE PART OF AIRIUS FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSE-
QUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED, TO ANY LOSS OF BUSINESS OR PROFITS,
WHETHER OR NOT FORESEEABLE.
Any and all disputes related to this warranty or any other maer related to Airius must be submied
to binding arbitraon within 45 radial miles of Longmont, Colorado. The arbitrator will follow the Col-
orado Uniform Arbitraon Act and the Rules of the American Arbitraon Associaon. Under Colorado
law, punive damages are not recoverable by any party subject to arbitraon. Moreover, jury trials are
not available in arbitraon. The arbitraon decision or award is legally binding and enforceable. To the
extent that a court rules that this paragraph is not enforceable, the pares agree to resolve any and all
disputes in the Boulder District Court in Boulder, Colorado.
Customer Service: 888-AIR-PEAR (888-247-7327) or inf[email protected]