Airlink101 AWLH3026T User manual

Ver.1A
Package Content:
•Wireless PCIAdapter
•Driver&UtilityCD
•Quick Installation Guide
Model#AWLH3026T
Section 1
Install Driver & Utility
Quick Installation Guide
802.11g Wireless PCIAdapter
This Quick Installation Guide only provides the basic instructions. For more
advancedfeaturessuchasconfiguringencryptionsettings,pleaserefertothe
User’sManual in the provided CD.
Note: Besure to power off your computer beforeinserting the PCI
adapter.ForWindows98SE and ME users, you may be prompted
to insert the Windows 98SE or ME CD during the driver installation.
Besuretohaveyour Windows98SEorMECDready.
Step 1 Insert the PCI adapter into an available PCI slot and turn on your
computer.
Step 2 Windows will launch the Found New Hardware Wizard. The wizard
appears differently depending on your operating system. Click Cancel to quit the
wizardandinsert the Driver & Utility CD into your CD drive.
Note: IftheAutorun screen doesn’t appear automatically go to Start, Run,
andtype D:\utility\setup.exe(where D is the letter of your CD drive) and
click OK.
Step 3 TheAutorun screen will appear. Select Install Utility and Driver from the
menu.

Continue on back...
ContinueonBack
Step 4 Click Next at the welcome screen.
Step 8 Verify Yes, I want to restart my computer now is selected and click
Finish to restart your computer.
Step 7 Click Continue Anyway at the Windows Logo Screen.
(For Windows 2000, click Yes at the Digital Signature Not Found prompt).
Step 5 Click Next to accept the default destination folder.
Step 6 Click Next to accept the default program folder.

Section 3
Section 2
Configure the Wireless PCI Adapter
To open the Wireless PCIAdapter’s utility go to Start > (All) Programs >
Airlink101 > WLAN Monitor.
Step 1 Select the SSID of the wireless network you wish to connect to from the
Available WLANs box and click Connect.
Note to Windows XP Users:
You must disable the Wireless Zero Configuration Utility in order to use the WLAN
Monitor. Please refer to the following steps to disable the Wireless Zero
ConfigurationUtility.
Step 1 Double-click on the Wireless Network Connection Icon in the system
tray and then click on Change advanced settings under Related Tasks.
Step 2 Go to the Wireless Networks tab, verify the “Use Windows to configure
my wireless network settings” box is unchecked and click OK.
Note: Theutilityautomaticallyadds an available wireless network to the
Preferred WLANs box. If no SSID is added, or if the SSID is wrong,
pleaserefertothefollowing steps to join the appropriate wireless network.
Be sure toremove the wrong SSIDfrom the Preferred WLANs boxbefore
adding any new SSID. You can remove the wrong SSID by selecting it and
clicking on Remove.

E-mail:[email protected]
TollFree:1-888-746-3238
WebSite:www.airlink101.com
Section 3
Technical Support
Section 4
Step 2 If you are connecting to an unsecured wireless network, a caution
message will appear. Click OK to exit the message.
Note: In some cases, you may need to restart your computer to complete
thewireless connection.
Step 3 Verify the SSID you have selected is in the Preferred WLANs box and
click Apply.
*TheoreticalmaximumwirelesssignalratebasedonIEEEstandard802.11gspecifications.Actualdata throughput will vary.Networkconditions
andenvironmentalfactors,includingvolumeofnetworktraffic,buildingmaterials and construction, mix of wireless products used, radio
frequencyinterference(e.g.,cordlesstelephonesandmicrowaves)aswellasnetworkoverheadloweractualdatathroughputrate.
Specificationsaresubjecttochangewithoutnotice.Allproductsandtrademarks are the property of their respective owners. Copyright ©2006
AirLink101™
Step 4 A blue circle appears indicating a connection is established. Click OK.