Airlink101 MIMO XR AWLH5026 User manual

Ver. 1A
Package Content:
•Wireless PCIAdapter
•Driver&UtilityCD
•Quick Installation Guide
Model#AWLH5026
Section 1
Install Utility Software
Quick Installation Guide
MIMO XR™ 802.11g PCIAdapter
This Quick Installation Guide only provides the basic instructions. For more
advancedfeaturessuch asconfiguring encryptionsettings,please referto the
User’sManual intheprovided CD.
Note: Besureto poweroffyour computerbeforeinserting thePCIadapter.
For Windows 98SE and ME users, you may be prompted to insert the Windows
98SE or ME CD during the driver installation. Be sure to have your Windows 98SE
or ME CD ready.
Step 1 Insert the PCI adapter into an available PCI slot and turn on your
computer.
Step 2After turning on the computer, Windows will launch the Found New
Hardware Wizard.TheFound NewHardware Wizardappearsdifferently
depending on your operating system. Click Cancel to quit the wizard and insert
theDriver& UtilityCDinto yourCD drive.
Note: IftheAutorun screendoesn’tappear automaticallygoto Start, Run,type
D:\Utility\Setup.exe (where D is the letter of your CD drive) and click OK to install
the utility directly.
Step 3 The Autorun screen will pop up. Select Install Utility from the menu.

Continue on back...
ContinueonBack
Step 4 Click Next at the welcome screen.
Step 7 Verify Yes, I want to restart my computer now is selected and click
Finish torestart yourcomputer.
Step 6 Click Continue Anyway at the Windows Logo Screen.
(For Windows 2000, click Yes at the Digital Signature Not Found prompt).
Step 5 Click Next to accept the default destination folder.

Section 3
Section 2
Configure the Wireless PCI Adapter
To open the Wireless PCI Adapter’s utility go to Start > (All) Programs >
Airlink101 MIMO PCI Utility >Airlink101 MIMO PCI Utility.
Step 1 Go to the AP List tab, select the SSID (Network Name) of the wireless
network you wish to connect to, and click Connect.
Step 2 If encryption is not enabled for the selected access point / router, skip to
step 6. Otherwise, enter a Profile Name for your wireless setting and click Next.
Step 3 Verify that the Network Name matches the SSID of your wireless network
and click Next.

E-mail:[email protected]
TollFree:1-888-746-3238
WebSite:www.airlink101.com
Section 3
Technical Support
Section 4
Step 4 Select the proper encryption setting for your wireless router or access
point from the drop-down menu and click Next.
Step 8Verifythatyou are receivingadequate Signal Strength and LinkQualityand
that you have been assigned a valid IP address (instead of all 0’s). If all 0’s, please
repeat step 1 - 5.
Step 5 Follow the on-screen instructions to complete the encryption settings.
Click Complete when finished.
Copyright©2006AirLink101.All rightsreserved.AirLink101, thestylizedAirLink101 logo,specificproduct designations,andall other words
andlogos thatare identifiedas trademarksand/or servicemarks are, unlessnoted otherwise,the trademarksand servicemarks of AirLink101.
Allother productor servicenamesare theproperty oftheirrespective holders.AirLink101 products areprotected undernumerous U.S. and
foreignpatentsand pendingapplications, mask work rights,andcopyrights.MIMOXR is aregisteredtrademark of Ralink Technology
Corporation.
*Theoreticalmaximum wirelesssignal ratebasedon IEEEstandard 802.11gspecifications.Actualdata throughputwill vary.Network conditions
andenvironmental factors,including volume ofnetwork traffic,building materials andconstruction, mixof wireless productsused, radio
frequencyinterference (e.g.,cordless telephonesand microwaves)as well asnetwork overheadlower actualdata throughput rate.
Step 6 You should see a blue circle around the antenna icon indicating a valid
connection.
Step 7 Go to the Link Information tab and click on the More button.