AirLive MD-3025-IVS User manual

MD-3025-IVS
e-Fence Guide
Version 1.0

MD-3025-IVS e-Fence Setup Guide
1
MD-3025-IVS
e-Fence Guide
1. Overview
The MD-3025-IVS has built-in video analytic function for e-Fence detection. It is a
standalone function built into the camera’s firmware without the need for external software
or device. The e-Fence function can be used to detect any objects when it crosses border
of detection areas. This guide will focus on using MD-3025-IVS’s “e-Fence”function to do
intruder detection in places like museum, residential area, warehouse, military structure, or
jail.
The e-Fence works by defining 1~4 zones on the video image. When a person or object
crosses the border or moves in/out the zone, the camera will detect the object immediately.
The important factors for successful e-Fence installations are:
Choose the appropriate installation location and avoid any shadow get into or pass
through the detecting area.
Choose the appropriate camera height (distance).
We will guide you through the procedure in the following articles.
2. Hardware Installation Guidelines
The followings are basic installation guidelines for best e-Fence results. However, the
e-Fence function can still work in less than ideal conditions.

MD-3025-IVS e-Fence Setup Guide
2
1. Prevent from any shadow comes into the detection area.
2. Make sure there is enough illumination.
(Noise will cause the false alarm.)

MD-3025-IVS e-Fence Setup Guide
3
3. Make sure the appropriate camera distance.
1080P
720P
Viewing Angle
Distance (Max.)
Viewing Angle
Distance (Max.)
Horizontal
15M
Horizontal
14M
※Note: The maximum distance is for reference only.
3. Camera Configuration
3.1 Finding camera using AirLive IP Wizard
The IPCAM’s default IP address is 192.168.1.100，but this address can change when there
is DHCP server(router) in your network. Therefore, please install AirLive IP wizard to find
your camera.
1. Install the “AirLive IP Wizard”from the installation CD or download it from this link.
2. Run the “setup.exe”and open the AirLive IP Wizard.
3. The IP Wizard will auto search and list out the camera found. Double click on the camera
that you want to configure.
4. The IPCAM’s web configuration will open automatically after double click. Please enter
the “admin”for username and “airlive”for password.
5. After entering the correct username and password. You will enter the camera’s web
configuration page. When prompted to install “Media Control”from “OvisLink Corp”,
please select “Yes”to install.

MD-3025-IVS e-Fence Setup Guide
4
3.2 Enable Camera’s Video Analytic function
Please use Internet Explorer as the default browser. If you are using IE 11, please go to
“Setup->Compatibility View Settings”and add the camera’s IP address to the list.
Please follow the steps below to enable camera’s video analytics function.
1. Click on “Configurations”on left menu bar
2. Click on “Video”on the left menu bar and select “enable”Intelligent Video Analytics.
3.3 Setting Resolution and Frame Rate
On the video page, it is important to set the appropriate resolution and frame rate.
Please remember to click on “Apply”button after finish settings.
!

MD-3025-IVS e-Fence Setup Guide
5
Main Stream Resolution
Main Stream Frame Rate
Second Stream Frame Rate
1080P
25FPS
15FPS
720P
25FPS
15FPS
3.4 Configure e-Fence Function
Please go to “Video Analytics”menu and select “e-Fence”
Below is the main page of e-Fence.

MD-3025-IVS e-Fence Setup Guide
6
The first step is to set the zones according to your environment. The controls are separated
in Zone Area and Zone Settings as indicated above.
Zone Settings
This is the default zone setting. When you click inside the “Zone Area”, you can move
and resize the zone by holding the “inside zone”and the “change points”.
Zone Area
Zone Settings
Click and hold inside
the zone to move the
block
Click and hold the
change points to resize
the zones.
Click inside the zones to
activate edit mode
Please remember to press “Apply”
after change settings, otherwise the
settings won’t take effect.

MD-3025-IVS e-Fence Setup Guide
7
Create another zone: When you press “Add Zone”button, you can create up to 4
zones to fit your need.
After you set the zone area correctly, the next step is to calibrate the object size according
to your installation.
Calibration
“Anything”is our recommendation and you don’t need to do the calibration. However, you
could also choose “People”or “Vehicles”to set “Calibration”when the camera cannot
detect objects accurately.
You can perform calibration by checking the “people”in the calibration field.
On the Zone Area, a window label “Min Size”will appear.
Click inside the small
box to change the size
Minimum Object Size
Click left mouse button
to set each position
Click right mouse
button to complete a
zone when you finish a
last position setting.
1
2
3
4
5
6
7

MD-3025-IVS e-Fence Setup Guide
8
Click on “Min. Size”window to change the size of the minimum object.
Min Size: Object smaller than this size will not be detected.
Other Important Settings
Detect: Please keep on “Anything”for an accurate detection.
Sensitivity: “Moderate to High”is the recommended settings
Statistic Chart Display: When enabled, it will show the result in a statistic graph. It is not
recommended to turn on this function as it might use a lot of CPU resource which can
influence the performance. If you use this function, please remember to turn it off after
finish using it.
Event Action
The camera’s e-Fence function can perform certain action when an event is met. For
example, it can be set if any object is moving into the detection areas, it will start to record a
video and send alarm email to user.
Example:
Setting if the object is moving into the detection areas between 7am to 9pm, the camera will
record an event video and send an email to user.
1. Go to the camera’s UI, select “Event->Media Format”, and choose recording period.
2. Check “Enable SMTP”, select SMTP or Gmail, and fill in all the relation data. (Please
press “Test SMTP”button to make sure your setting is correct or not.)

MD-3025-IVS e-Fence Setup Guide
9
3. Go to “Video Analytics”and “e-Fence”. You can change the “Interval”to have the time
interval between events.
4. Now, please click on “Set Event Action”. Click on “Add”. Then the following screen will
appear. Please enter the data as shown below. Please remember to click on “Save”
after finish settings.
Note: The Event Name does not allow spaces in between words. Please enter the
event name as one single word.
!