AirLive 2.5GE XPON ONU User manual

AirLive 2.5GE XPON ONU
Quick Installation Guide
V1.0

AirLive 2.5GE XPON ONU QIG_V1.0
1. Indicator and Interface Description
1.1 Product Picture
Figure 1 2.5GE XPON ONU
1.2 Application Chart
Figure 2 Application Chart
1.3 Panel Lights
Figure 3 Panel Lights

AirLive 2.5GE XPON ONU QIG_V1.0
LED
Mark
Status
Description
System
SYS
On / Off
System is not running or fatal error.
Blink
Normal running.
Registration
PON
On
The device is registered to the PON system.
Off
The device is not registered to the PON
system.
Blink
The device is registering.
Optical signal
loss
LOS
Blink
Device does not receive optical signal.
Off
Device receives optical signal.
LAN
LAN1
LAN2
On
Port is connected properly.
Off
Port connection exception or not connected.
Blink
Port is sending or/and receiving data.
Table 1 Panel Lights
1.4 Interface/button Panel
12 3 4 5
Figure 4 Interface/button Panel
Name
Function
1: PON
Connect to OLT by SC type fiber connector, single mode optical fiber cable.
2/3: LAN1/2
The blue LAN2 is 2.5GbE port and the yellow LAN1 is 1GE port. Connect to
PC or other devices with Ethernet port by Cat5/Cat5E cable, RJ-45
connector.
4: RST
Press RST button over 10 seconds, ONU restores factory default and
reboots.
5: DC 12V
Connect with power adapter. DC 12V, 0.5A.
Table 2 Interface/button Panel

AirLive 2.5GE XPON ONU QIG_V1.0
2. Packing List
Contents
Quantity
Contents
Quantity
2.5GE XPON ONU
1 pcs
Power adapter
1 pcs
Installation Guide
1 pcs
3. Certification
The following products have been tested by us with the listed standards and found in
compliance with the European directive 2014/35/EU / EMC directive 2014/30/EU. It is
possible to use CE marking to demonstrate the compliance with the LVD / EMC directive.
EN 62368-1:2014+A11:2017
EN 55032:2015+A1:2020
EN 55035:2017+A11:2020
EN IEC 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A2:2021
4. Hardware Installation
Installation Environment Requirements
ONU equipment must be installed in the interior, and to ensure the following conditions:
⚫Confirmation at the ONU installation at sufficient space to facilitate cooling machine.
⚫ONU suitable operating temperature of -5 ℃~ 55 ℃, humidity 10% to 90%.
⚫Device workplace should avoid radio transmitters, radar stations, and high-frequency
interference from power equipment.
Equipment Installation
1. Installed on the desktop
Place the ONU on a clean bench, this installation is relatively simple, you can observe the
following operation:
⚫Ensure the smooth workbench.
⚫Around the device there is enough space for heat dissipation.
⚫Do not place objects on the device.
2. Mounted on the wall
⚫Observation ONU equipment chassis two cruciform recess, in accordance with the
position of the groove, installed two screws in the wall.
⚫The original selected two mounting screws gently snap into recesses aligned.
⚫Slowly let go, so that the device under the support of the screw hanging on the wall.
3. Connect fiber, network cable and power adapter to the corresponding interfaces, and turn
on the power of product.