AIS Fibre HUMAX ONT User manual

HUMAX (ONT)
Installation
1
Strictly Confidential

LED Status indicator
LED Description
POWER
Off
Device
is off/No have electric current
Green
LED
on
Normal
status
CONNECTION
Off
OLT
does not connect to HUMAX
Green
LED
on
The
connection between OLT and
HUMAX
is
registered
Green
LED
blink
The
connection between OLT and
HUMAX
is
not registered
ALARM
Off
Normal
status
Red
LED on
Cable
has some issue
ETH
Off
LAN does not
connect / LAN has some
issue
Green
LED
on
CPE
and HUMAX do not not sync data
Green
LED
blink
CPE
and HUMAX is syncing data
Front
Strictly Confidential

On/Off
Fiber cable wire LAN Port
System Connection
Description
LAN Port
Connect
LAN with HUMAX
and WAN Port(Blue Port) of
CPE
On/OFF
On
(I) / Off (0)
DC
PWR Port
DC 12 Volt with
HUMAX
Fiber Port
Plug fiber cable
HUMAX
Back
Port Information
3
Strictly Confidential

Overview of HUMAX Connection
Strictly Confidential 4
Fiber Cable
PC Staff
192.168.1.254
Humax ONT(SFU)
192.168.1.1
VDSL CPE
WAN port (Blue)
LAN Port1
(Yellow)
DHCP
Electric Cable
Note: The system connection
in this page has to set before
start an activation
On
Blink Off
LED at Power/Internet/WAN/LAN1/WLAN on
and hold

Activation
Strictly Confidential 5
Click HP11X.exe and press Enter

①Connect : Connection button to login with IP that
showed on ONT IP Address (192.168.1.254)
②Disconnect : Disconnect with HUMAX
③Get Password : See current password (Activation
number) that was set to HUMAX
④Set Password : Set new password
This button can use after enter a correct
activation number in 8 already
⑤Retrieve Optical RX/TX power : Click on this
button to measure the optical power that will
show in 9
⑥Exit : Exit an application
⑦ONT IP address : IP address of HUMAX
⑧ONT password : Enter Activation number
⑨Rx Power / Tx Power
1 2
34
5
7
6
8
9
Application Details
6
Strictly Confidential

Strictly Confidential 7
- After start a program, the window will be
displayed. Click Connect
- Program will display a message
“Succeeded to connect the device” if a
connection is successfully
Step 1
On
Blink
Off
1. Click Connect

Strictly Confidential 8
- In another way, the message
“Couldn’t connect to the device”
will be displayed if the device cannot
connect
Step 1 (Continue)
On
Blink
Off
1. Click Connect

Strictly Confidential
-Click on ”Retrieve Optical Rx/Tx
Power” to measure RX/TX Power
- Program will send message
“Succeeded to retrieve Rx/Tx”
-Record Rx/Tx
Step 2
2. Click
On
Blink
Off
9

Strictly Confidential
-Click ”Get Password” an old password of ONT
will display in ONT Password
- Change ONT Password by enter Activation
number of customer
-Press ”Set Password” then the background of
a message “Succeeded to connect the device”
will change to green
Step 3
2. Click
3.Enter Customer’s activation number
4. Click
On
Blink
Off 10

Strictly Confidential
Step 4
On
On
Off
On/Blink
Successful
Turn off HUMAX then turn on again
- If activation number is correct the
LED status will display like a figure
below
- If activation number is wrong, Check
an activation number then do a step
3 again
11

Registration
12
Strictly Confidential

Step 1
- Launch browser, it will redirect to registration page automatically
- If the page is not showed, go to
network.ais.co.th/?cond=registration&accesstype=VDSL
13
Strictly Confidential

Step 2
- Enter last 4-digits of activation number then press Submit
- Enter Keyword of company then press Submit
14
Strictly Confidential

15
Step 3
- The page will display as figure below, that means a registration is successful
Strictly Confidential

The steps to retrieve
Rx/Tx after installation
16
Strictly Confidential

Strictly Confidential 17
- If HP11X.exe was closed when the
installation finished, it will cannot
connect to HUMAX when start HP11X.exe
again
- A program will show message “Couldn’t
connect to the device”
Step 1
1. Click

Strictly Confidential 18
Step 2
Fiber cable
PC
Staff
192.168.1.254
Humax
ONT(SFU)
192.168.1.1
VDSL CPE
LAN Port1
(yellow)
DHCP
Electric cable
Fiber cable
PC
Staff
192.168.1.254
Humax
ONT(SFU)
192.168.1.1
VDSL CPE
LAN Port1
(yellow)
DHCP
Electric Cable
-Change LAN connection of VDSL CPE from WAN port (blue) to LAN Port 2 (yellow)
WAN Port (blue)
LAN Port2
(yellow)

Strictly Confidential 19
- Click Connect
-Click “Retrieve Optical Rx/Tx Power”
- Record
Step 3
1. Click
2. Click

Strictly Confidential 20
Step 4
Fiber cable
PC
Staff
192.168.1.254
Humax
ONT(SFU)
192.168.1.1
VDSL CPE
LAN Port1
(yellow)
DHCP
Electric cable
Fiber cable
PC
Staff
192.168.1.254
Humax
ONT(SFU)
192.168.1.1
VDSL CPE
LAN Port1
(yellow)
DHCP
Electric cable
-Change LAN connection back
LAN Port2
(yellow) WAN Port (blue)