AJ 406002 User manual

MR2208MD
Version 1.0
Note: The owner and user MUST read and
understand these operating instructions
before using this product.
Operating Instructions
[406002] Office shredder

Parts and function
2 | ajproducts.com
Jam
Overheat
Door open
Bin full
Power Power cord inlet Power On / Off
Paper entry
Card/CD entry
Operation buttons
Rev
Power On / Off
Fwd
Window
Bin door
Castor
Warning signs
Do not exceed the maximum capacity
of sheets per pass
Read and learn the warnings written in
this document
Avoid touching the document
feed opening with hands
Avoid hair touching the
document feed opening
Product is not intended for use
by children (product is not a toy)
Avoid clothing touching the
document feed opening
Keep aerosol products
away
Do not shred paper clips
1. Avoid touching exposed blades under Micro-cut shredder head.
2. The grounded socket outlet should be installed near the equipment
and be easily accessible.
3. This equipment is not suitable for use in locations where children
are likely to be present.
Keep body parts away from
moving parts

1. 1.
3. 3.
5.
4. 4.
6.
2. 2.
Feed the paper into the
entry and release.
The machine will start
the shredding process
automatically.
3 | ajproducts.com
Capabilities Maintenance
Operation
Will shred:
Paper, CD/DVD’s, credit cards, staples
Will not shred:
Continuous forms, adhesive labels, transparencies,
newspaper, paper clips, cardboard, wet paper, laminates or
plastics other than noted above
Paper shred size:
Micro-cut ............................................................ 2x15mm
Maximum:
Sheets per pass ....................................................8 (70g)
Passes per day:..................................................... 50-100
Cards per pass............................................................... 1
Cards per day .............................................................. 50
Paper width .......................................................... 230mm
Duty cycle.................................................. 10-15 minutes
( Heavier paper, humidity or other than rated voltage
may reduce capacity)
Lubricate when or immediately, if:
- Capacity decreases
- The motor sounds different, or shredder stops running
Set to ” ”
Shred one sheet.
Only use a non-aerosol vegetable oil in long
nozzle container
Set to ”Rev” for 2-3
seconds.
Apply oil across entry. Press ”Fwd”.
For paper: For credit cards/CD:
Please check the voltage
of your shredder carefully
before using and then plug
in the cable, set the switch
to ”I” position.
Please check the voltage
of your shredder carefully
before using and then plug
in the cable, set the switch
to ”I” position.
Feed the credit cards/
CD into the marked entry
and the machine will start
the shredding process
automatically.
If you want to stop the
shredding process, press
the ”Rev” button for 2-3
seconds.
The machine will reverse
and eject the papers.
Press ”Power ON/OFF”, the
Power LED lamp should
be turned on green and
indicate standby mode.
Press ”Power ON/OFF”, the
power LED lamp should
be turned on green and
indicate standby mode.
Set switch to ”O” and
unplug the cable after use.
Set switch to ”O” and
unplug the cable after use.
Press ”Power ON/OFF”, the
power LED lamp should
be turned off and indicate
sleep mode.

4 | ajproducts.com
Troubleshooting Recycling
Continuous operation beyond 10-15 minutes may
trigger cool down period for over 30 minutes due
to overheat. Turn off the unit after use.
1. Paper jam
Symptom: Indicator light
Solution:
2. Bin open
Symptom: red light
indicates door open.
Solution: Check the bin
and make sure it´s closed
correctly.
3. Bin full
Symptom: red light
indicates bin full.
Solution: Take out the bin
and empty it. Put the bin in
place until the light goes
out.
Press ”Rev” for 2-3
seconds.
Gently pull uncut paper
from the paper entry, then
plug in the machine again.
Press ”Rev” and
alternately back and
forth.
Press
to restart the
shredder.
Press
and unplug.
The crossed-out wheelie bin symbol
indicates that the item must not be
disposed of with normal, unsorted
general waste. The item must be sent
to separate collection facilities for
recovery and recycling in accordance
with local waste disposal regulations.
By separating electronic equipment
and batteries from general waste, you
help reduce the volume of waste sent
to incineration or landfill and minimise
any potential negative effects on the
environment and human health.
The information in this document is subject to change
without notice.
Please visit our website for the latest version.
ajproducts.com