Akai PDP5006H User manual

SERVICE MANUAL
Model:
PDP-5006H
Safety Precaution
Technical Specifications
Block Diagram
Circuit Diagram
Basic Operations & Circuit Description
Main IC Specifications
Trou le Shooting Manual of PDP Module
Spare Part list
Exploded View
If You Forget Your V-CHIP Password
Software Upgrade
This manual is the latest at the time of printing, and does not
include the modification which may be made after the printing,
by the constant improvement of product.

Safety Precaution
ACAUTION
RISK OF L CTRIC SHOCK
DO NOT OP N
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL ONLY.
AThe lightning flash with arrowhead sym ol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclo
sure that may e of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
P R E C A U T IO N S D U R IN G
S ER V IC IN G
1. In addition to safety, other parts and
assem lies are specified for conformance with
such regulations as those applying to spurious
radiation. These must also e replaced only
with specified replacements.
Examples: RF converters, tuner units, antenna
selection switches, RF ca les, noise- locking
capacitors, noise- locking filters, etc.
2. Use specified internal Wiring. Note especially:
1) Wires covered with PVC tu ing
2) Dou le insulated wires
3) High voltage leads
3. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulating Tape
2) PVC tu ing
3) Spacers (insulating arriers)
4) Insulating sheets for transistors
5) Plastic screws for fixing micro switches
4. When replacing AC primary side components
(transformers, power cords, noise locking
capacitors, etc.), wrap ends of wires securely
a out the terminals efore soldering.
5. Make sure that wires do not contact heat
generating parts (heat sinks, oxide metal film
resistors, fusi le resistors, etc.)
6. Check if replaced wires do not contact sharply
edged or pointed parts.
7. Make sure that foreign o jects (screws, solder
droplets, etc.) do not remain inside the set.
M A K E Y O U R C O N T R IB U T IO N
T O P R O T E C T T H E
E N V IR O N M E N T
Used atteries with the ISO sym ol \5<9
for recycling as well as small accumulators
(rechargea le atteries), mini- atteries (cells) and
starter atteries should not e thrown into the
gar age can.
Please leave them at an appropriate depot.
W A R N IN G :
Before servicing this TV receiver, read the
SAFETY INSTRUCTION and PRODUCT
SAFETY NOTICE.
S A F E T Y IN S T R U C T IO N
The service should not e attempted y anyone
unfamiliar with the necessary instructions on this
apparatus. The following are the necessary
instructions to e o served efore servicing.
1. An isolation transformer should e connected in
the power line etween the receiver and the
AC line when a service is performed on the
primary of the converter transformer of the set.
2. Comply with all caution and safety related
provided on the ack of the ca inet, inside the
ca inet, on the chassis or picture tu e.
3. To avoid a shock hazard, always discharge the
picture tu e's anode to the chassis ground
efore removing the anode cap.
4. Completely discharge the high potential voltage
of the picture tu e efore handling. The picture
tu e is a vacuum and if roken, the glass will
explode.

5. When replacing a MAIN PCB in the ca inet,
always e certain that all protective are
installed properly such as control kno s,
adjustment covers or shields, arriers, isolation
resistor networks etc.
6. When servicing is required, o serve the original
lead dressing. Extra precaution should e given
to assure correct lead dressing in the high
voltage area.
7. Keep wires away from high voltage or high
tempera ture components.
8. Before returning the set to the customer,
always perform an AC leakage current check
on the exposed metallic parts of the ca inet,
such as antennas, terminals, screwheads, metal
overlay, control shafts, etc., to e sure the set
is safe to operate without danger of electrical
shock. Plug the AC line cord directly to the
AC outlet (do not use a line isolation
transformer during this check). Use an AC
voltmeter having 5K ohms volt sensitivity or
more in the following manner.
Connect a 1.5K ohm 10 watt resistor paralleled
y a 0.15pF AC type capacitor, etween a
good earth ground (water pipe, conductor etc.,)
and the exposed metallic parts, one at a time.
Measure the AC voltage across the com ination
of the 1.5K ohm resistor and 0.15 uF
capacitor. Reverse the AC plug at the AC
outlet and repeat the AC voltage measurements
for each exposed metallic part.
The measured voltage must not exceed 0.3V
RMS.
This corresponds to 0.5mA AC. Any value
exceeding this limit constitutes a potential
shock hazard and must e corrected
immediately.
The resistance measurement should e done
etween accessi le exposed metal parts and
power cord plug prongs with the power switch
"ON". The resistance should e more than
6M ohms. AC VOLTM T R
P R O D U C T S A F E T Y N O T IC E
Many electrical and mechanical parts in this
apparatus have special safety-related
characteristics.
These characteristics are offer passed
unnoticed y visual spection and the protection
afforded y them cannot necessarily e o tained
y using replacement components rates for a
higher voltage, wattage, etc.
The replacement parts which have these
special safety characteristics are identified y A
marks on the schematic diagram and on the parts
list. Before replacing any of these components,
read the parts list in this manual carefully. The
use of su stitute replacement parts which do not
have the same safety characteristics as specified
in the parts list may create shock, fire, or other
hazards.
9. Must e sure that the ground wire of the AC
inlet is connected with the ground of the
apparatus properly.
Good earth ground
such as the water
- pipe, conductor,
etc.
1500 ohmi, lOwatt
Place this probe
on each exposed
metallic part
AC Leakage Current Check

Technical Specifications M O D L : PDP-5G0eH
5 0 ” P la s m a D is p la y
DAT FIRST ISSU D ISSU
1
RAIS D BY CH CK D BY NUMB R OF PAG S
9
R VISIONS
ISSU D DAT D SCRIPTION RAIS D BY :
SP CIFICATION AGR D : SIGNATUR DAT
R & D D PARTM NT
COMM RCIAL D PARTM NT
PRODUCTION D PARTM NT
Q/A D PARTM NT
CUSTOM R
SPECIFICATION APPROVED : SIGNATURE : DATE
NOTE : Only d ocu m en ts stam p ed “C ontrolled D o cu m e nt to b e u sed for m an ufactu re of production parts.

Technical Specifications PDP- 006H
CONTINUATION PAG
NUMB R 2 OF 9 PAG S
1. S ta n d ard T e s t C o n d itio n s
All tests shall e performed under the following conditions, unless otherwise specified.
1.1 Am ient light
1.2 Viewing distance
1.3 Warm up time
1.4 PDP Panel facing
1.5 Measuring Equipment
1.6 Magnetic field
1.7 Control settings
1.8 Power input
1.9 Am ient temperature
1.10 Display mode
1.11 Other conditions
150ux (When measuring IB, the am ient luminance
= 0.1Cd/m2)
50cm in front of PDP
30 minutes
no restricted
PC, Chroma 2225 signal generator (with Chroma digital
additional card) or equivalent, Minolta CA100 photometer
no restricted
Brightness, Contrast, Tint, Color set at Center(50)
100~240Vac
20°C ± 5°C (68°F ± 9°F)
31.5KHz/60Hz (Resolution 1366 x 768)
1.11.1 With image sticking protection of PDP module, the luminance will descend
y time on a same still screen and rapidly go down in 5 minutes. When
measuring the color tracking and luminance of a same still screen, e sure t
o accomplish the measurement in one minute to ensure its accuracy.
1.11.2 Due to the structure of PDP, the extra-high- right same screen should not
hold over 5 minutes for fear of randing on the panel.

Technical Specifications PDP- 006H
CONTINUATION PAG
NUMB R 3 OF 9 PAG S
L C T R IC A L C H A R A C T R IS T IC S
2. P o w e r In p u t
2.1 Voltage
2.2 Input Current
2.3 Maximum Inrush Current
Test condition
2.4 Frequency
2.5 Power Consumption
Test condition
2.6 Power Factor
2.7 Withstanding voltage
3. D is p la y
3.1 Screen Size
3.2 Aspect Ratio
3.3 Pixel Resolution
3.4 Peak Brightness
3.5 Contrast Ratio (Dark room)
3.6 Viewing Angle
3.7 OSD language
4. S ig n a l
4.1 AV & Graphic input
4.1.1 Composite signal
4.1.2 Y,C Signal
4.1.3 Component signal
4.1.4 Graphic I/P
4.1.5EDID compati ility
4.1.6 I/P frequency
100 ~ 240VAC
5.0 /2.5A
<30 A (FOR AC110V ONLY)
Measured when switched off for at least 20 mins
50Hz to 60Hz(±3Hz)
< 480W
full white display with maximum rightness and
contrast
Meets I EC 1000-3-2
1.5kVac or 2.2kVdc for 1 sec
50” Plasma display
16:9
1366x768
1000 cd/m2 (Panel module without filter)
5000:1 (Panel module without filter)
Over 160°
English
CVBS
S-Video
Y, P /C , Pr/Cr, HDTV compati le
Analog: D-su 15pin detacha le ca le
Digital: DVI
DDC 1.3
fH 31.5kHz to 60kHz/fV: 56.25Hz to 75Hz (1024X768
recommended)

Technical Specifications PDP- 006H
CONTINUATION PAG
NUMB R 4 OF 9 PAG S
4.2 Audio input
Audio I/P(L/Rx5)
4.3 AV output
Audio&Video O/P(RCAx3)
4.4 Other function :
5. n v iro n m e n t
5.1 Operating environment
5.1.1 Temperature :
5.1.2 Relative humidity:
5.2 Storage and Transport
5.2.1 Temperature :
5.2.2 Relative humidity:
6. P a n e l C h arac te ris tic s
6.1 Type
6.2 Size
6.3 Aspect ratio
6.4 Viewing angle
6.5 Resolution
6.6 Weight
6.7 Color
6.8 Contrast
6.9 Peak rightness :
6.10 Color Coordinate Uniformity :
Test Pattern :
1 for DVI / D-Su
1 for Y/ P /Pr
1 for Y/ C /Cr
1 for CVBS
1 for S-Video
: Monitor out(Video & Audio L/R)
PIP/POP/PBP, Picture size, Picture Still, Sound mode,Last
memory, Timer, MTS
5° to 33°C
20% to 85%(non-condensing)
-20°C to 60°C(-4° to 140°F)
5% to 95%
S50HW-XD03
50”, 1190mm(width)x7005mm(height)x59mm(depth)±1
mm)
16:9
Over 160°
1366X768
22.0kg ±0.5 kg (Net)
1024(R)X1024(G)X1024(B) COLORS
Average 60:1 (In a right room with 150Lux at center)
Typical 5000:1 (In a dark room 1/100 White Window
pattern at center).
Typical 1000cd/m2 (1/25 White Window)
Contrast; Brightness and Color control at norma
setting
Full white pattern
Average of point A,B,C,D and E +/- 0.01

Technical Specifications PDP- 006H
CONTINUATION PAG
NUMB R 5 OF 9 PAG S
6.11 Color temperature Contrast at center (50); Brightness center (50);
Color temperature set at Natural
x=0.285±0.02
y=0.290±0.02
6.12 Cell Defect Specifications
Su ject to Panel supplier specification as appends.
7. F ro nt P a n e l C o ntro l B utto n
7.1 Sele Up / Down Button
Volume Up/ Down Button
Menu Button
Source Select Button
7.2 Stand y Button
7.3 Main Power Switch
8. O S D F u n c tio n
Push the key to select Item up or down.
When selecting the item on OSD menu.
Push the key to increase the volume up or down.
When selecting the adjusting item on OSD menu
increase or decrease the data- ar.
Enter to the OSD menu.
Push the key to select the input signals source.
Switch on main power, or switch off to enter power
Saving modes.
Turn on or off the unit.
8.1 Picture : State (Normal,Dark,Bright,User); Display (Bright,contrast,Color,Hue)
Temp (warm,Cool,Normal,User);
Position (H-posit,V-posit,Phase,H-size,Auto Adjust)
8.2 Sound : Setup (Mode,AVC,Volume,Balance);
Equalizer (120HZ,500HZ,1.5KHZ,5KHZ,10KHZ)
BBE Setup (Gain,Tre le,Bass)
8.3 OSD : Size (Panorama,16:9,Normal,Anamorphic,Letter Box,TV Mode)
OSD Set (Language,OSD Position,Time Out)
Option (Burn Protect, Version)
V-Chip , C/C
8.4 Layout : Layout (Full Screen,PIP,Split Screen,Grid,POP 3,POP 12)
PIP Set (Su Win Source,Su Win Size,PIP Size.PIP Position)
8.5 Time : Sleep (30Min,60Min,90Min,120Min,180Min)
Wake Up (Time Edit,Volume,TV Mode,Channel)
Time Set

Technical Specifications PDP- 006H
CONTINUATION PAG
NUMB R 6 OF 9 PAG S
9. A g e n c y A p p ro va ls
Safety UL60950
Emissions FCC class B
10. R e lia b ility
11.1 MTBF
11. A c c e s so rie s
20,000 hours(Use moving picture signal at 25°C am ient)
User manual x1, Remote control x1, Stand x1, Power cord x1,
Battery x 2, Accessories ox x 1 ,Speaker x 2,Speaker wire x2

CONTINUATION PAG
Technical Specifications PDP- 006H NUMB R 7 OF 9 PAG S
12. Support the Signal Mode
A. D-Su Mode (VGA or DVI)
NO. Resolution Horizontal
Frequency
(KHz)
Vertical
Frequency
(Hz)
Dot Clock
Frequency
(MHz)
1 640 x 400 31.47 70.08 25.17
2640 x 480 31.50 60.00 25.18
3640 x 480 35.00 67.00 30.24
4640 x 480 37.50 75.00 31.50
5640 x 480 37.86 72.81 31.50
6720 x 400 31.47 70.08 28.32
7800 x 600 35.16 56.25 36.00
8800 x 600 37.90 60.32 40.00
9800 x 600 46.90 75.00 49.50
10 800 x 600 48.08 72.19 50.00
11 832 x 624 49.00 74.00 57.27
12 1024x 768 48.40 60.00 65.00
13 1024x 768 56.50 70.00 75.00
14 1024x 768 60.00 75.00 78.75
15 1152x 864 54.53 61.13 80.37
16 1152x 864 63.86 70.02 94.51
17 1152x 864 67.52 75.02 108.03
18 1280x 960 60.02 60.02 108.04
19 1280x 1024 64.00 60.01 108.00
B. DTV Mode
NO. Resolution Horizontal
Frequency
(KHz)
Vertical
Frequency
(Hz)
Dot Clock
Frequency
(MHz)
1 480 i 15.734 59.94 13.50
2576 i 15.625 50.00 13.50
3480p(720x480) 31.468 59.94 27.00
4576p(720x576) 31.25 50.00 27.00
5720p(1280x720) 45.00 60.00 74.25
6720p(1280x720) 37.50 50.00 74.25
71080i(1920x1080) 28.125 50.00 74.25
81080i(1920x1080) 33.75 60.00 74.25
- When the signal received y the Display exceeds the allowed range, a warning message "Out Of Range”
shall appear on the screen.
- You can confirm the input signal format from the "OSD Menu”.

CONTINUATION PAG
Technical Specifications PDP- 006H NUMB R 8 OF 9 PAG S
4 .4 R e m o te C o n tro l
0 Power ( 6 ): Press to turn on and off.
2 Mute ( ^
): Press to mute the sound. Press
again or press ◄ or ► to restore the sound.
3 P.STILL: Press to freeze the picture. Press
again to restore the picture.
4 P.SIZE: Press to cycles through the picture
size: Normal, Fill Screen, Anamorphic,
Letter Box, TV Mode or Panorama.
5 P. MODE: Press to cycles through the picture
mode: NORMAL, BRIGHT, DARK, USER.
© S.SELE: Press to cycles through the sound
select: Main window sound or Su window
sound.
0 PIP: Press to turns on PIP (picture-in-
picture) feature. Such as Full Screen, PIP or
Split Screen.
8 SWAP: Press to switches the Main window
or Su window pictures.
9 C/C: Press to select the Closed Caption
mode.
10 V-Chip: Press to select the child protect
mode.
11 TIME: Press to display the current time.
12 SLEEP: Press repeatedly until it displays
the time in minutes (30 Min, 60 Min, 90 Min,
120 Min, 180 Min or Off ) that you want the
PDP to remain on efore shutting off. To
cancel Sleep Time, press SLEEP repeatedly
until Sleep Off appears. And you can press
◄ or ► to select sleep time shut down.
13 Num er uttons: Use these uttons to
enter password.
(Note: The 100 button is inactive in this model.)
14 PIP Source: Press to select the signal for Su Window.(Only for PIP.)
15 F.WHITE: Press to show a full white picture.
16 INFO: Press to display on-screen information.
17 SOUND: Press to select different sound system, such as Normal, Flat, News, Cinema,
User or BBE Digital.
18 PICTURE: Press to select “BRIGHT”, “COLOR”, “CONTRAST”, ”HUE” or “SHARP”, and
you can use^ or ► to adjust.
19 EXIT: Press to return or exit OSD menu.
1
3
4
7PIP SWAP C/C V-CHIP r
□ C D
-GD C l>
P.STILL P.SIZE P.MODE/S.SEIE
t f j f c l d T C D r
TIME SLEEP
© © ©
© © ©
© © ©'
©
PIP Source F.WHITE INFO 1 100
-E D ED CD CD
SOUND PICTURE EXIT SOURCE
-ED ED ED ED-
2
5
12 ( ontinued on next page)

CONTINUATION PAG
Technical Specifications PDP- 006H NUMB R 9 OF 9 PAG S
21 SOUND: Press to select different sound system, such as Normal, Flat, News, Cinema,
User or BBE Digital.
22 PICTURE: Press to select “BRIGHTNESS”, “COLOR”, “CONTRAST”, ”HUE” or
“SHARPNESS”, and you can use A or ► to adjust.
23 EXIT: Press to return or exit OSD menu.
24 SOURCE: Press to select the signal sources directly. Such as TV, AV1, S-VIDEO,
YC Cr, YP Pr, Analog RGB or Digital RGB.
23 MENU: Press to display the OSD Menu.
23 OK: Press to enter or confirm.
21 ▲ / ▼ : They are used as ▲ / ▼ uttons in the OSD Menu screen and they can e
used for the selection of the program when the OSD Menu is not shown on the screen.
23-4 / ► : They are used as -4 / ► uttons in the OSD Menu screen and they can e
used for the adjustment of volume when the OSD Menu is not shown on the screen.
P H Y S IC A L C H A R A C T R IS T IC S
14. P o w e r C o rd
Length : 1.8m nominal
Type : optional
15. C a b in e t
15.1 Color : silver colour as defined y colour plaque reference num er
15.2 Weight
Net weight :
Gross weight : 51.8kg 74kg
15.3 Dimensions (with stand&speak)
Width :
Height :
Depth :
1227.8mm
739.8mm
120.6mm

Block Diagram Product Specification of PDP Module
LVDS Input
Control Signal —
(Serial Interface)
APL Data
Input
Interface
Controller
Memory
Controller
Driver
Timing
Controller
Display data, Driver timing
>
•c
Q
G
cd
O
GO
Color Plasma Display Panel
13 X 7 8 pixels
Address Driver
<u
>
•G
T3
cö
3
c
O
o
o
Vs(180V~190V)
Va(55V~65V)
Vcc(+5V)
Applied Voltage level is specified at the time when Full-White pattern is displayed on the panel.

Block Diagram MAIN/AUDIO BOARD

Circuit Diagram
- Power supply board of Audio Amplifier,
- Main (Video) board
- Sub (Audio) board
- Keypad board
- Remote control receiver board
- Remote control board

MPT012A

1

DbhM4812V12 Vtek BOM.sch-3 - Wed Oct 06 23:58:10 2004
TTTyTTTTTT
[3 ] MAX_TX[? ------[.
[3 ] MAX_RX[)------|_
j _ um
v c c ADO.PD.D
AD1.P0.1
EA.VP AD 2.P 0.2
AD3.P0.3
RESET AD 4.P 0.4
AD5.P0.5
P1.0.T2 AD6.PÛ.6
P1.1.T2EX AD 7.P0.7
P1.2
P1.3.PWM0
P1.4.PWM1 AB .P2.0
P1.5.PWM2 A9.P2.1
P1.6.PWM3 A10.P2.2
P1.7.PWM4 A11.P2.3
A12.P2.4
P3.0.RXD A13.P2.5
P3.1.TXD (B)A14,P2.B
P3.2.IN T0 (B)A15 ,P2.7
P3.3.INT1
P3 .4 .T0 ALE.P
P3.5.T1 PSEN
WR.P3.6
XI RD.P3.7
X2 P4.0
P4.1
INT3.P4.2
GND (B )IN T2,P4,3
I ----- X SB_SC L [3 ]
1 ----- < SB_SDA [3 ]
CE20Q D201
W - D200
W -
H h
I— Öl- X1 VCC
X? sn i
SI)A
INI A
SOW GND
1 SB_SCL [3]
SB_SDA [3]
Project:
D u h e M a in
Rev:
1 .2
Title:
M ic o m B l o c k
Date: Sheet:
S E P .1 0 ' 2 0 0 4 0 3 o f 13

DbhM4812V12 Vtek BOM.sch-4 - Wed Oct 06 23:58:11 2004
. DF04 1 b DnF04,
» DF 05 ? 7 R DF ilfi
„ DFOfi 3 ■'S/VS/ b o n rn fi,
» DF 07 4 5 D n m z
„ DFOB 1
I
A2 52 B DDFOfl.
» UFOS 7 7 DnFns,
„ DF10 3 6 DDF10,
» DF11 4 /w v 5 RDF11 ,
„ DF17 1
'S/VS/
A2 53 B DDF17/
» DF1.1 7 /y v v 7 RDFI.T.
. DF14 3 6 DDF14/
» DF15 4 /w v 5 DHF15,
„ DF1fi 1 FA254 R DDF16.
. DF17 2 7 DDF17,
v DF18 3 / y v v R DDF18.
„ n n q 4 5 DDF19,
„ DF 70 1
I
FA 255 fi DDF20.
„ DF71 7 — : 7 DDF21,
v D F22 3 R D DF2Z
, DF23 4 5 DDF23,
1
p s i
DDF[00 :23]
~m ------
11 DDF07/
10 n o m a .
9DDFOL
-| 17 DDF07,
11 IÎD F0.1
in DDF04,
RDF05,
I 17 DDF14/
RDF15,
in DDFOR.
R0F09,
I 17 DDF10/
IÎDF11 ,
in I50F17/
DDF13,
i 1? DDF22,
11 DDF23,
10 DDF16,
DDF17,
l 1? DDF18,
11 DDF19,
10 DDF20,
9DDF21,
11 nn sn7 .
10 n n s o a
n n s m .
I 17 DDS07,
n n s n .\
10 ODSfH,
9IÎDS05.
I 17 n n s u ,
DDS15/
10 nnsna,
nn sns,
I 17 D0S10/
IÎDR11 ,
10 D0S17/
IÎDR1.T,
I 17 DDS2Z
DDS23.
10 DDS16,
DDS17,
-|1? DDS18.
11 DDS19,
10 DDS20.
9DDS21,
[4 TD1 +
[4 A 2 -
[4 f A 2 +
[4 Î B 2 -
[4 T B 2 +
. DDF01 52
. DDF02 54
. DDF03 55
. DDF04 56
. DDF05 3
. DDF08 50
. DDF07 2
. DDF08 4
. DDF09 6
. DDF10 7
. DDF11 11
. DDF12 12
. DDF13 14
. DDF14 B
. DDF15 10
. DDF16 15
. DDF17 19
. DDF1B 20
. DDF19 22
. DDF20 23
. DDF21 24
. DDF22 16
. DDF23 1B
FOR DUAL THINE FORMAT
>CL KIN PVCC
TA0(R2,RD)
TA1(R3,R1) LVDSVCC
TA 2(R4,R 2)
TA3lR 5,R 3)
TA 4(R6,R 4) VCC1
TA 5(R7,R 5) VCC2
TD0(R0,R6) RS(VCC)
TD1(R1,R7)
TA6ÎG 2.G0 ) TXOUTG—
TB0(G3,G1) TXOUTO+
TB1(G4,G2)
TB2(G5,G3) TXOUT1-
TB3 G6.G4) TXOUT14
TB4 G 7.G5)
TD2 G0,G6) TXO UT2 -
TD3(G1,B7) TXOUT2+
TX CLK-
TB5(B2,B 0) TXCLK+
TB6(B3,B1)
TC 0(B4,B2) TX OUT3-
TC1(B5,B3) TXOUT3+
TC 2(B 6,B4)
TC3 B 7.B 5) GND1
TD4 B 0.B6 ) GND2
TD5(B1,B7) GND3
GND4
GND5
TC4(HS)
TC5 VS) 0GND1
TC61EN) OGND2
TD6(RES) OGND3
R FB (THINE,NS) Pg n D1
PWRDN# PGND2
-R
. DDSOB1 4
TA1+ [4 ] . DDS091 6
. DDS101 /
TB1- [4 ] . DDS11 1 11
TB1+ [4 ] . DDS121 17
. DDS131 14
TC1- [4 ] . DDS141 K
TC1+ [4 ] . DDS151 1U
TCLK1—[4 ]
TCLK1-K4]
1
. DDS161 15
. DDS171 19
TD1- [4 ] . DDS181 70
TD1+ [ 4 ] . DDS191 22
>CLKIN PVCC
TA0(R2,R 0)
TA1(R3,R1) LVDSVCC
TA2(R 4,R2)
TA3(R 5,R3)
TA4 R6,R4) VCC1
TA5 R 7.R 5) VCC2
TD0(R0,R6) RS(VCC)
TD1(R1,R7)
TA6(G2,G0) TXOUTO—
TB0(G3,G1) TXOUTO+
TB1(G4,G2)
TB2(G5,G3) TX 0UT1-
TB3(G6,G4) TX0UT1+
TB4(G7,G5)
TD2(G D,G6) T X 0 U T 2 -
TD3(G1,G7) TX0 UT2+
TX CLK-
TB5(B 2,B0) TXCLK+
TB 6fB 3,Bl)
TCD(B4,B2) T X 0U T 3 -
TC1(B5,B3) TX0UT3+
TC 2(B 6,B 4)
TC 3(B 7,B 5) GND1
TD4(BD,B6) GND2
TD5(B1,B7) GND3
GND4
GND5
TC4(HS)
TC5 VS ) 0GND1
TC6ÎEN) 0GND2
TD6(RES) 0GND3
R FB (THINE,N S) p GND1
PWRDNjf PGND2
-R
St -R
T A 2 - [4 ]
TA 2+ [4 ]
T B 2 - [ 4 ]
TB2+ [ 4 ]
T C 2 - [4 ]
TC2 + [4 ]
TCLK2 - [4 ]
TCL K2+ [4 ]
T D 2 - [4 ]
TD2+ [4 ]
Project:
D u h e M a in
Rev:
1 .2
Title:
T T L & L V D S O u t p u t
Date: Sheet:
S E P .1 0 ' 2 0 0 4 0 4 o f 1 3