Akerstroms SESAM 800 L99 Series User manual

942858-000 EN -C1
OPERATING MANUAL
SESAM 800
L99
RX, RXD and RX DIN

2 (28)
Table of Contents
1 Introduction ______________________________________________ 3
2 Scope ___________________________________________________ 3
3 Service __________________________________________________ 3
4 Maintenance ______________________________________________ 3
5 TechnicalSpecications ____________________________________ 4
6 Description of the System __________________________________ 5
6.1 Receivers _________________________________________________ 5
6.2 Transmitter ________________________________________________ 6
7 Description of the Receivers_________________________________ 6
8 Installation of the Receiver __________________________________ 9
8.1 Placement of the Receiver ____________________________________ 9
8.2 Antenna Placement ________________________________________ 10
8.3 Connections on the Receiver (all models) _______________________ 10
9 Indicators on the Receivers ________________________________ 11
9.1 Sesam 800 RX ___________________________________________ 11
9.2 Sesam 800 RXD __________________________________________ 11
9.3 Sesam 800 RX DIN ________________________________________ 12
10 CongurationoftheReceiver_______________________________ 12
10.1 Sesam 800 RX ___________________________________________ 12
10.2 Sesam 800 RX DIN ________________________________________ 13
10.3 Sesam 800 RXD __________________________________________ 13
10.4 High Security Transmission Mode _____________________________ 17
10.5 Memory Card (only Sesam 800 RXD) __________________________ 17
11 Description of the Sesam 800 L99 ___________________________ 19
11.1 Indications on the Transmitter ________________________________ 20
12 UsingtheSystem _________________________________________ 20
13 CongurationoftheTransmitter ____________________________ 21
13.1 Group ID_________________________________________________ 21
13.2 Display Window Illumination__________________________________ 22
14 Installation of Holder ______________________________________ 23
14.1 Mounting and Attach Holder ________________________ 23
14.2 Installation of Power Supply to the Holder __________________ 24
14.3 The Holder Antenna Placement ________________________ 24
14.4 Make the holder powerless __________________________________ 24
15 ReplacingBatteriesintheTransmitter _______________________ 25
16 Error Codes _____________________________________________ 26
17 Receiver Drill Measure for RX and RXD_______________________ 27
17.1 Measure for RX DIN________________________________________ 27

Introduction 3 (28)
Sesam 800 L99 RX/RXD/RX DIN (original instructions) Document-ID: 942858-000 EN
Version: C1 Author: SH
1 Introduction
This manual only covers the installation of the Sesam radio remote door
opening system. The Sesam System is not a complete door opening system:
it provides only the set of outputs that are driven according to the actions
performed by the operator of the transmitter. The way the set of outputs is used
for controlling the doors depends on the specic installation and is outside the
scope of the Sesam.
The approvals that the Sesam radio remote control system is only valid for the
system itself.
The complete remote control system, where the controlled object is one part,
has to be tested and approved according to the standards/norms that are ap-
plicable and specic to the controlled object, it is not the responsibility of
Åkerströms Björbo.
2 Scope
The following guide must be used when installing Åkerströms Sesam door
opening system to ensure secure, safe operation. The installation must be car-
ried out by a certied electrician.
3 Service
Contact your Åkerströms Björbo AB dealer for service or support. Warranty
work must be performed by Åkerströms or authorized service center.
4 Maintenance
For cleaning use a dry cleaning cloth, if necessary use a wet cleaning cloth and
a soap solution. Never use an alcohol-based product for cleaning; it can seri-
ously damage the plastic. Do not use pressure washer on the product!

Technical Specications 4 (28)
Sesam 800 L99 RX/RXD/RX DIN (original instructions) Document-ID: 942858-000 EN
Version: C1 Author: SH
5 TechnicalSpecications
Table 1. Technical Specications, Sesam 800 L99 RX RXD
SystemSpecications
Operating frequency: 869,8 MHz
Channel separation: 25 kHz
Power output: < 5 mW
Functional sensitivity: <= -107 dBm BER 10-4
Transmission principle: GMSK, TDMA,
Operating Temperature: -25°C - +55°C
Storage Temperature: -40°C - +85°C
RX&RXDspecications
IP- class: IP65
Power Supply, 12-24 V DC versions: 12-24 V DC/AC 150 mA (SELV), 4AT fuse.
Power Supply, 230 V AC versions: 230 V AC 50 Hz 15 mA, 4AT fuse.
Max switching capacity of relays: 2A/250VACwithcosφ=1
Total load on all relays: 4A/250 V AC (not exceeding 2A on any
single relay)
Relay- type SPDT
Fuse on current loop: 2,5AT/250 V AC (IEC 60127-2/V)
Dimensions:
(for more detail see chap. 17)
135 x120 x 50 mm
Weight: 450g
Screw Size: TX20
DINspecications
Power Supply 12-24 V AC/DC
Max switching capacity of relays: 2A/250VACwithcosφ=1
Fuse on current loop: 2,5AT/250 V AC (IEC 60127-2/V)
Dimensions: 92 x72,5 x 30 mm
Weight: 84g

Description of the System 5 (28)
Sesam 800 L99 RX/RXD/RX DIN (original instructions) Document-ID: 942858-000 EN
Version: C1 Author: SH
L99Specications
IP- class: IP67
Dimensions: 120x75x30
Weight: 200g
Battery type: 2*AA Alkaline
Screw Size: PH2
6 Description of the System
6.1 Receivers
This document covers three receiver models; RX, RXD and RX DIN.
RX and RXD can be ordered as 230 VAC or 12-24 VAC/DC.
RX DIN can be ordered only as 12-24 VAC/DC.
Sesam 800 RX:
1
• 3 Single Pole Double Throw relays.
• Memory capacity: up to 100 transmitters.
Sesam 800 RXD:
• 3 Single Pole Double Throw relays.
1
• Integrated display and conguration buttons.
• Memory capacity: up to 500 transmitters.
• The receiver can be equipped with a detachable memory
card containing a backup of all conguration param-
eters.
Sesam 800 RX DIN: 1
• 3 Single Pole Double Throw relays.
• Memory capacity: up to 100 transmitters.
• Designed for DIN rail
1Type label position

Description of the Receivers 6 (28)
Sesam 800 L99 RX/RXD/RX DIN (original instructions) Document-ID: 942858-000 EN
Version: C1 Author: SH
6.2 Transmitter
This document covers the Sesam 800 L99 transmitter.
1
Important features are:
• A transmitter suitable for controlling
up to 1000 dierent doors.
• Integrated back lighted display
• Optional cassette with external power
and antenna connectors
1Type label position
7 Description of the Receivers
12 3
4 5 67 8 9
R1 R2 R3
4
5
6
7
1
2
3
8
9
14
10 11 12 13
Figure 1. Sesam 800 RX 230 VAC
model indicators, connections and jumper.
1. LED 1 Relay 1 status
2. LED 2 Relay 2 status
3. LED 3 Relay 3 status
4. LED 4 Power LED
5. LED 5 Squelch
6. LED 6 Status
7. LED 7 Learn
8. Power connection 230 VAC
9. Jumper J1 High Security
Transmission Mode setting
10. Learn/Erase button
11. Connection to relay 1, ARROW UP
12. Connection to relay 2, STOP
13. Connection to relay 3, ARROW DOWN
14. Antenna connector

Description of the Receivers 7 (28)
Sesam 800 L99 RX/RXD/RX DIN (original instructions) Document-ID: 942858-000 EN
Version: C1 Author: SH
12 3
4 5 67 8 9
R1 R2 R3
4
5
6
7
1
2
3
8
9
14
10 11 12 13
Figure 2. Sesam 800 RX 12-24 V DC
model indicators, connections and
jumper.
1. LED 1 Relay 1 status
2. LED 2 Relay 2 status
3. LED 3 Relay 3 status
4. LED 4 Power LED
5. LED 5 Squelch
6. LED 6 Status
7. LED 7 Learn
8. Power connection 12-24 V AC/DC
9. Jumper J1 High Security
Transmission Mode setting
10. Learn/Erase button
11. Connection to relay 1, ARROW UP
12. Connection to relay 2, STOP
13. Connection to relay 3, ARROW
DOWN
14. Antenna connector
1234
5

Figure 3. Sesam 800 RXD 12-24 V DC/
AC model connections
1. Power connection
2. Connection to relay 1, ARROW UP
3. Connection to relay 2, STOP
4. Connection to relay 3, ARROW DOWN
5. Antenna connector

Description of the Receivers 8 (28)
Sesam 800 L99 RX/RXD/RX DIN (original instructions) Document-ID: 942858-000 EN
Version: C1 Author: SH
1234
5

Figure 4. Sesam 800 RXD 230 V AC
model connections
1. Power connection,
2. Connection to relay 1, ARROW UP
3. Connection to relay 2, STOP
4. Connection to relay 3, ARROW DOWN
5. Antenna connector
12
3
4
5
Figure 5. Sesam 800 RXD model dis-
play and buttons
1. Learn/Erase button
2. Enter button
3. Memory position up button
4. Memory position down button
5. Display
Figure 6. Sesam 800 RX DIN model
connections and buttons
1. Learn/Erase button
2. Power connection,
3. Connection to relay 1
4. Connection to relay 2
5. Connection to relay 3
6. LED 5 Squelch
LED 6 Status
LED 7 Learn

Installation of the Receiver 9 (28)
Sesam 800 L99 RX/RXD/RX DIN (original instructions) Document-ID: 942858-000 EN
Version: C1 Author: SH
8 Installation of the Receiver
The permanent installation of the receiver must include fuses that protect the
equipment and wiring from overcurrent and short-circuit. In detail the power
supply of the receiver and all relay contacts must be fused.
All fuses are used as disconnecting devices. The fuses shall be easily accessible,
must submit a contact gap of at least 3.0 mm and have to be placed in the line
pole. Note that the fuse must be compatible with IEC 60127-2/V.
After the installation of the equipment, the installed cables must be bound
together (i.e. by using a cable binder) very close to the terminal blocks.
Note that there might be hazardous voltage in the receiver; therefore only certied
electricians are allowed to open the lid.
8.1 Placement of the Receiver
Select a location that is within the environmental limitations of the receiver and
where it is dicult for unauthorized persons to obtain access to the receiver. If
possible, mount the receiver with the cable glands facing downwards.
For the drilling measure of SESAM RX and RXD see chapter 17.
These receivers are preferably screwed with 4 mm screws
suitable for the surface. Think of the antenna’s size and inu-
ence of any metal objects when choosing placement.
SESAME RX DIN is to be mounted on a DIN rail. On the
back there is a recess that the rail ts in (see 1 in g. 7).
When the recess is pressed against the rail the snap t
(see 2 in g. 7) will lock the receiver to the rail automatically.
Make sure that is snap. To remove, withdraw the snap t and
lift the receiver o the rail.
Figure 7. DIN receiver, the lock for the rail.

Installation of the Receiver 10 (28)
Sesam 800 L99 RX/RXD/RX DIN (original instructions) Document-ID: 942858-000 EN
Version: C1 Author: SH
8.2 Antenna Placement
Attach the supplied antenna to the antenna connector on the receiver. Note that
the antenna must not be placed near metal objects such as wiring, tin roof, etc.
If an antenna cable is needed, contact Åkerströms Björbo AB.
8.3 Connections on the Receiver (all models)
The receiver is equipped with connections for relays; power and an external
antenna (see g. 1, g. 2, g. 3, g. 4 and g. 6).
The connections for power connection are, from left to right:
• Line (L)
• Neutral (N)
The connections for each relay are, from left to right:
• Common terminal
• Normally opened (NO)
• Normally closed (NC)
LN
1 2 3 4 5 6 7 8 9
(C) (NO) (NC) (C) (NO) (NC) (C) (NO) (NC)
R1 R2 R3
Figure 8. Power connection and Relay connection
Connection example:
• R1 = UP
• R2 = STOP
• R3= DOWN