Russound SaphIR 858 User manual

LIMITED WARRANTY
The Russound 858 IR Receiver is fully guaranteed for two (2) years from the date of pur-
chase against all defects in materials and workmanship. For this warranty to apply, the unit
must be installed and used according to its written instructions. During this period,
Russound will replace any defective parts and correct any defect in workmanship without
charge for either parts or labor. Accidental damage and shipping damage are not consid-
ered defects under the terms of this warranty. Russound assumes no responsibility for
defects resulting from abuse or servicing performed by an agency or person not specifical-
ly authorized in writing by Russound. If service is necessary, it must be performed by
Russound. Damage to or destruction of components due to excessive power voids the
warranty. In these cases, the repair will be made at the owner’s expense. To return for
repairs, the unit must be shipped to Russound at the owner’s expense, along with a note
explaining the nature of the service required. Be sure to pack in a corrugated container
with at least 3 inches of resilient material to protect the unit from damage in transit.
Before returning a unit for repair, call Russound at [phone] for a Return
Authorization number. Write the RA number on the shipping label and ship to: Russound,
ATTN: Service, 5 Forbes Road, Newmarket NH 03857
Russound sells product only through authorized Dealers and Distributors to ensure that
customers obtain proper support and service. Any Russound product purchased from an
unauthorized dealer or other source, including retailers, mail order sellers and online sellers
will not be honored or serviced under existing Russound warranty policy. Any sale of prod-
ucts by an unauthorized source or other manner not authorized by Russound shall void
the warranty on the applicable product.
5 Forbes Rd. Newmarket, NH 03857, USA
☎ 603.659.5170 • Fax [phone]
e-mail: [email protected]
Come visit us at:
OTHER RUSSOUND PRODUCTS
IR RECEIVER
Decora®Style In-Wall
Infrared Receiver
858
Instruction Manual
Decora®is a trademark of Leviton Corporation
Patented
EMITTER PORTS
857
CONNECTING
BLOCK
123456
IR R ECEIVER I N
IR C OMMON I N
IR C
ONFIRM
+ 12VDC
GND
STATUS
SIGNAL
EMITTERS
S TATUS
+12VDC
P OWER
+12VDC
DESIGNED IN USA MADE IN KOREA
857 INFRARED
CONNECTING BLOCK

PRODUCT OVERVIEW
The 858 IR Receiver receives IR signals from a handheld IR remote control
and relays this to the audio/video equipment for operation from another
room. Mounts to a single gang J-Box using a Decora®cover plate.
FEATURES
•Stylish Decora®design. Available in white or almond colors
•Dual color LED. Green for system status and blue for talk back.
•Ultra thin design. Mounts easily in any J-box or P-ring.
•Wide band IR. Receives IR from many types of remotes.
INSTALLATION
Connect the 858 to the 857 (or equivalent) connecting block using 2 twisted
pair wire. Use one pair to connect GND (GROUND) and IR (SIGNAL). Use the
other pair to connect ST (STATUS) and V+ (+12VDC). If the wire has a shield,
connect it to the ground at both ends. See Figure 1 for detail of these
connections.
STATUS INDICATOR
To use the status indicator on the 858 connect the 12 Volt 100mA or higher
power supply to the STATUS line of the 857 connecting block as shown in
Figure 2. Plug the power supply into the switched outlet on the stereo
receiver. When the receiver is on, the power supply will turn on the system
status line and illuminate the LED Green of the 858.
EMITTER PORTS
857
CONNECTING
BLOCK
123456
IR R ECEIVER I N
IR C OMMON I N
IR C
ONFIRM
+ 12VDC
GND
STATUS
SIGNAL
EMITTERS
S TATUS
+12VDC
P OWER
+12VDC
DESIGNED IN USA MADE IN KOREA
857 I
NFRARED
C
ONNECTING
B
LOCK
CONNECT TO
846C POWER
SUPPLY
ST IR GND V+
2-TWISTED
PAIR WIRE
SHIELD WIRED
TO GROUND
12 VDC
Figure 1
Figure 3
EMITTER PORTS
857
CONNECTING
BLOCK
123456
IR R ECEIVER I N
IR C OMMON I N
IR C
ONFIRM
+ 12VDC
GND
STATUS
SIGNAL
EMITTERS
S TATUS
+12VDC
P OWER
+12VDC
DESIGNED IN USA MADE IN KOREA
857 I
NFRARED
C
ONNECTING
B
LOCK
12 VDC
Figure 2
The status line can be turned on or off by setting the jumper on back of the
858 as shown in Figure 3.
MOUNTING
Mount the 858 to the J-Box using the screws that are supplied. Mount the
cover plate (not included) to the IR receiver. See Figure 4.
SPECIFICATIONS
Receive Frequency: 36kHz to 58kHz
Transmit Frequency: 40kHz and 56kHz
Range: On Axis – 55ft to 80ft
30º Off Axis – 30ft to 55ft
Power: 12VDC 31mA max.
Status Power: 12VDC 3mA max.
Wire requirements: 2 twisted pair, with or without shield
Dimensions: 1 3/4”W x 4 5/16”H x 3
/8”D
Weight: 1/2oz
ST IR GND V+ ST IR GND V+
STATUS ON STATUS OFF
Figure 4