Akron STYLE 3600 User manual
STYLE 3600 WIRELESS REMOTE CONTROL
INSTALLATION AND OPERATING INSTRUCTIONS
The following is intended to provide the basic instructions for installation and operation of the Wireless Remote Control
(WRC), and to assist in attaining the best possible performance from the unit. Read and understand these operating
instructions before use.
TOOLS REQUIRED
•MediumPhillipsscrewdriver •Smallatscrewdriver
PRODUCT WARNINGS
WARNING: Forreghtinguseonlybytrainedreghters.
WARNING: Although the enclosures for the controller and receiver are water-resistant, it is important to keep water
out of the enclosure. Prolonged exposure to water will cause damage. When the cover of the enclosure
is removed, make sure the O-ring under the cover is intact and free of dirt and debris.
WARNING: Do not use the WRC when the override cranks are being used or are in position for use.
WARNING: Replacetheidenticationtagsiftheyshouldbecomewornordamaged.
WARNING: Donotstowthemonitorwhenowingwater
PRODUCT SPECIFICATIONS
Handheld Controller
•Inputpower Two–1.5vLithiumAAbatteries*
•Batterylife 20continuoushours
•Outputpower MeetsFCCpart15requirementforlicensefreeoperation
•Controllerdimensions 61⁄4”x31⁄2”x13⁄4”
•Controllerweight 3⁄4lb
•Operatingtemperaturerange -40°Fto140°F(-40°Cto60°C)
•Controllerpower 1mW
•OperatingFrequency 2.4GHzor900MHz(seelabelforfrequency)
•FCCID OUR-XBEE
•Range 500ft
NOTE: Enclosing the receiver in a compartment or behind the pump panel will reduce the effective range.
Receiver
•Inputpower 12or24VDC
•Receiverdimensions 41⁄2”x31⁄2”x2”
•Receiverweight 1⁄2lb
•Operatingtemperaturerange -40°Fto140°F(-40°Cto60°C)
•Receiverpower 100mW
•OperatingFrequency 2.4GHz900MHz(seelabelforfrequency)
•FCCID OUR-XBEE
•SecurityCode 64bitcodefromserialnumberofmodule
*EarlymodelsusedoneCR123orequivalentLithiumBattery
120315
!
!
!
!
!
MECHANICAL ATTACHMENT OF RECEIVER
Belowarethemountingholedimensionsforthereceiver.Mountthereceivertoallowenoughcableforproper
installationtotheLogicBox(SeeElectricalLayout).Thereceiverwillcomewitha10ft.cable.
ELECTRICAL INSTALLATION OF RECEIVER
The following is the wiring chart for the Receiver to the Logic Box. These color-coded wires should be wired into the
inputsideoftheLogicBox(TB1).The+V(power)and-V(ground)canbewiredintoTB2.
*TheAuxbuttoncanbeusedforStow,DeployorOscillationifavailableonthemonitor.Wirethewhite/redwireintothe
correspondingterminalrequestedbycustomerfortheappropriatefunction.Seemonitoroperatinginstructions(orLogic
BoxLid)forwiringdiagramandterminallocation.**RunjumperwirefromTB3#7toTB3#3tohavetheAuxLEDonthe
handheld controller indicate if the monitor is stowed or deployed.
•AuxLEDON-Deployed
•AuxLEDOFF-Stowed
SYNCHRONIZE HANDHELD CONTROLLER WITH RECEIVER
•Beforeinitialoperationcanoccur,theHandheldControllermustbesynchronizedwiththeReceiver.
This allows proper communication between the two and ensures that the handheld Controller will only
controltheoperationofoneReceiver.Synchronizationisperformedonlyoncewhenthesystemisput
intooperationforthersttimeorifitbecomesdesirabletosynchronizetheHandheldControllerwitha
differentReceiver.AnunsynchronizedHandheldwillashallLED’sinunisonwhenitisturnedon.This
willcontinueforapproximately20secondsatwhichtimetheunitwillpowerdown.NewHandheld
controllersareshippedunsynchronized.
RECEIVER WIRE COLORS TERMINAL POSITION IN LOGIC BOX
WHITE +V12/24VPOWER TB1#10
WHITE/BLACK -VGROUND TB3#15
GRAY LED TB3#8**
WHITE/RED AUX *
BLACK RIGHT TB1#6
RED LEFT TB1#5
BLUE DOWN TB1#4
GREEN UP TB1#3
YELLOW STREAM TB1#2
BROWN FOG TB1#1
ORANGE STOW(USEDONLYFORSIT) TB1#21
PURPLE DEPLOY(USEDONLYFORSIT) TB1#22
FOGLEFTLOWER
RAISERIGHT
STOW
DEPLOY
SS
WARNING
FOGLEFTLOWER
RAISERIGHT
STOW
DEPLOY
SS
WARNING
1.33"
3.89"
10ft.
Cable
Logic
Box
Receiver
ELECTRICAL LAYOUT
2
1. MakesureonlytheintendedReceivermoduleispoweredon.IfmultipleReceiversarepowered,the
HandheldunitwillsynchronizewiththeReceiverwhichreturnsthestrongestsignal.Normallythisisthe
ReceiverandanyshieldingorreectivematerialmayoccasionallycausenearbyReceivertoreturna
weak signal.
2. StartingasynchronizeprocedurecanonlybedoneatpowerupwiththeHandheldunit.TheHandheld
unitcannotbemadetorequestasynchronizationonceithasstarteditsnormaloperation.
3. Inanattempttopreventunwantedsynchronizing,thekeystrokesrequiredtoinitiatesynchronizinghave
a time limit. Once the time limit has passed, the Handheld unit must be powered off before a new
synchronizationcanbestarted.
4. TosynchronizeaHandheldunitwithaReceiver,followthestepsbelow:
5. HoldtheAUXbuttondownwhilepoweringuptheHandheldunit.TheHandheldunitispoweredupby
brieypushingandreleasingthePowerON/OFFbutton.ReleasetheAUXbuttonanytimeafterthe
greenOn/Off/TransmitLEDcomeson.
6. Withinthenext3secondspushandreleasetheAUXbuttonagain.AfterashortdelaytheHandheld
unitwillstartsendingrequeststotheReceiverforaserialnumber.Upto6requestswillbemadewhile
theHandheldlistensforanyReceiversinthevicinity.TheHandheldwillthenashallLED’soncefor
each Receiver which responded to the Handheld. The Handheld will then select the Receiver with the
strongest signal.
7. IfanewHandheldunitcontinuestoashallLED’sinunisonafteranattemptismadeto synchronizeit
toaReceiver,thesynchronizationattemptwasunsuccessful.Thisisusuallyduetoimproperly
implementingthesynchronizationsequenceofbuttonpushes.SimplyturntheHandheldoffandtryagain.
8. IfaHandheldunitisnotnewandhasbeenpreviouslysynchronizedtoaReceiver,itcanbe
synchronizedtoadifferentReceiverifdesired.InthiscasethesynchronizationtotheoldReceiveris
lostwhenthesynchronizationtothenewReceiverisestablished.Ifsynchronizationfails,thehandheld
unitwillreturntoblinkingallLED’sinunison.
OPERATING INSTRUCTIONS
A. HANDHELD CONTROLLER OPERATION
TheHandheldcontrollerisusedtocontrolthemonitorandnozzle.
1.Tochangethehorizontalmonitorpositiontowardtherightorleft:
Presstheproperbutton“RIGHT”or“LEFT”respectively,aslabeledonthecontroller,untilthedesiredpositionis
reached.
2.Tochangetheverticalmonitornozzlepositionupwardordownward:
Presstheproperbutton“RAISE”or“LOWER”respectively,aslabeledonthecontroller,untilthedesiredpositionis
reached.
3.Tochangethenozzlepatterntowardthestraightstreamorfogposition:
Presstheproperbutton“STRAIGHT”or“FOG”respectively,aslabeledonthecontroller,untilthedesirednozzleposition
is reached.
4.TheAUXbuttoncanbeusedforanStow,DeployorOscillationdependingontheelectricalinstallationoftheAUXwire
inthelogicbox.(SeeElectricalInstallationofReceiver)
5.TheAUXLEDisastatusLEDreportingthestateofthesignalatTB1#9intheLogicBox.Itisupdatedwhenthe
HandheldunitispoweredupbutthereafteronlywhentheHandheldismovingthemonitorornozzle.TheAUXLEDis
alsoupdatedfor20secondsaftertheAUXbuttonisreleased.ThegreenOn/Off/TransmitLEDwillcontinuetoashdur-
ingthe20secondsthattheHandheldisupdatingtheAUXLED.
B. POWER DOWN
Thecontrollerwillautomaticallypowerdownafter5minutesofnon-activitytoconservebatterylife.
C. LOW BATTERY
TheON/OFFtransmitLEDontheHandheldwillturnredwithapproximately2hoursofcontinuoustransmissiontime
remaining before the battery(s) are completely discharged. There is a transition period in which the LED will alternate
between red and green as the battery voltage slowly falls.
D.BATTERYREPLACEMENT
Forunitswithtwo1.5VAALithiumbatteries,removethebatterycoverontherearofthecontrollerandremovetheold
batteries. Replace with new batteries and replace the battery cover. Be sure to observe the polarity markings in the
batterycompartment.Inanemergency,normal1.5VAAalkalinebatteriescanbeusedtopowerthecontrollerforseveral
hours of continuous use.
3
ISO 9001 REGISTERED COMPANY
PHONE: 330.264.5678 or 800.228.1161 I FAX: 330.264.2944 or 800.531.7335 I www.akronbrass.com
WARRANTY AND DISCLAIMER: We warrant Akron Brass products for a period of ve (5) years after purchase against defects in materials or workmanship. Akron Brass will repair or replace
product which fails to satisfy this warranty. Repair or replacement shall be at the discretion of Akron Brass. Products must be promptly returned to Akron Brass for warranty service.
We will not be responsible for: wear and tear; any improper installation, use, maintenance or storage; negligence of the owner or user; repair or modication after delivery; damage; failure to
follow our instructions or recommendations; or anything else beyond our control. WE MAKE NO WARRANTIES, EXPRESS OR IMPLIED, OTHER THAN THOSE INCLUDED IN THIS WARRANTY
STATEMENT, AND WE DISCLAIM ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Further, we will not be responsible for any consequential,
incidental or indirect damages (including, but not limited to, any loss of prots) from any cause whatsoever. No person has authority to change this warranty.
© Premier Farnell Corporation. 2000 All rights reserved. No portion of this can be
reproduced without the express written consent of Premier Farnell Corporation.
revised: 6/10
For single battery Handheld units, remove the four screws on the back of the Handheld and carefully remove the back
cover. It maybe necessary to use a small screw driver to remove the battery from its holder. Be careful to not damage
any components on the circuit board during battery replacement.
E. BACKLIGHT
The controller is equipped with a backlight to illuminate the buttons when visibility is limited. The backlight will turn off
after 30 seconds of non-activity. Press any button to turn the backlight back on.
Table of contents
