Alarm Lock PG21 SERIES User manual

MAGNETIC
ACTUATOR
INSTALLATION TEMPLATE--PG21 SERIES
USE RIGHT SIDE OF PAGE
FOR OUTSWINGING DOORS
AS SHOWN IN THE "TOP
VIEW" BELOW (NOTE
LOCATION OF HINGE).
PG21
DOOR
MAGNETIC ACTUATOR
HINGE
PG21 SERIES
FOLD UP ALONG THIS LINE & PLACE AGAINST EDGE OF DOOR
FOLD UP ALONG THIS LINE & PLACE AGAINST EDGE OF DOOR
3/8"
© ALARM LOCK 2003
ALARM LOCK
345 Bayview Avenue, Amityville, New York 11701
WI1210A 9/03
USE LEFT SIDE OF PAGE
FOR OUTSWINGING DOORS
AS SHOWN IN THE "TOP
VIEW" BELOW (NOTE
LOCATION OF HINGE).
MAGNETIC ACTUATOR
PG21
DOOR
HINGE
3/8"
(OPTIONAL--DO NOT DRILL
THIS HOLE EXCEPT FOR
EXTERNAL WIRING)
(OPTIONAL--DO NOT DRILL
THIS HOLE EXCEPT WHEN
INSTALLING A RIM CYLINDER)
!Holes for Baseplate
mounting screws.
Use 1/8" bit (0.125").
Drill 1" deep.
!Holes for Baseplate
mounting screws.
Use 1/8" bit (0.125").
Drill 1" deep.
Magnetic Actuator location is shown for reference purposes only. For correct Magnet Actuator location, use either (1) the location references printed on the red stickers on the side of the PG21 cover, (2) Mag- net Alignment Mode or (3) place the Magnetic Actua- tor 1½ " from the bottom edge of the Baseplate. For mounting hole sizes and depths, see reverse.
NOTE: The Baseplate must be
mounted far enough away from
the edge of the door to prevent
unit from striking the door jam.
MAGNETIC
ACTUATOR
JAM JAM
Magnetic Actuator location is shown for reference purposes only. For correct Magnet Actuator location, use either (1) the location references printed on the red stickers on the side of the PG21 cover, (2) Mag- net Alignment Mode or (3) place the Magnetic Actua- tor 1½ " from the bottom edge of the Baseplate. For mounting hole sizes and depths, see reverse.

MAGNETIC
ACTUATOR
MAGNETIC
ACTUATOR
INSTALLATION TEMPLATE--PG21 SERIES
© ALARM LOCK 2003
ALARM LOCK
345 Bayview Avenue, Amityville, New York 11701
WI1210A 9/03
USE LEFT SIDE OF PAGE
FOR DOORS SHOWN IN THE
"TOP VIEWS" BELOW
USE RIGHT SIDE OF PAGE
FOR DOORS SHOWN IN THE
"TOP VIEWS" BELOW
!Holes for Baseplate
mounting screws.
Use 1/8" bit (0.125").
Drill 1" deep.
PG21 SERIES
3/8"
3/8"
(OPTIONAL--DO NOT DRILL
THIS HOLE EXCEPT FOR
EXTERNAL WIRING)
(OPTIONAL--DO NOT DRILL
THIS HOLE EXCEPT WHEN
INSTALLING A RIM CYLINDER)
FOLD UP ALONG THIS LINE. PLACE ON DOOR AND DOOR JAM
FOLD UP ALONG THIS LINE. PLACE ON DOOR AND DOOR JAM
!Holes for Baseplate
mounting screws.
Use 1/8" bit (0.125").
Drill 1" deep.
Use 1/8" bit
(0.125").
Drill 1" deep.
Use 1/8" bit
(0.125").
Drill 1" deep.
Use 1/8" bit
(0.125").
Drill 1" deep.
Use 1/8" bit
(0.125").
Drill 1" deep.
(Double Doors)
(Double Doors)
(Double Doors)
(Double Doors)
NOTE: Both the Baseplate and
Magnetic actuator can be
mounted close to the edge of the
door and door jam.