Alberici Hira 2 Mini User manual

1
Progettazione e produzione di sistemi di pagamento e accessori per macchine Gaming, Vending e Car-Wash
Designand manufacture ofpayment systems and accessories forthe Industries ofGaming,Vendingand CarWash
Hira 2 Mini, Midi,Maxi
Operator’s Manual
Rev. 2.00 EN
HIRA 2
Operator’s Manual

2

3
CONTENTS
1. Package content:......................................................................................................................4
2. Components description ..........................................................................................................4
3. Product description..................................................................................................................5
4. Warning ..................................................................................................................................5
5. Installation ..............................................................................................................................6
6. Operation ................................................................................................................................9
7. System configuration...............................................................................................................9
8. Messages...............................................................................................................................17
9. Cleaning of the Note Validator..............................................................................................22
11. Disposal of the product ..........................................................................................................24
12. Terms of Guarantee ...............................................................................................................24
13. Customer Service...................................................................................................................24
STORICO REVISIONI
Revisione n°
Data
Modifica
Note
Creazione 1.00
30.12.14
Creazione
FW v. 1.14 (scheda CMS Full)
Rev. 1.01
18.02.15
Funzioni abilitazione/disabilitazione e erogazione via GSM.
FW v. 1.16
Rev. 1.02
10.03.15
Aumentato timeout visualizzazione valore svuotato. Inserito 1’
Timeout di uscita in menu svuotamento
FW v. 1.18
Rev. 1.03
27.06.15
Abbassato timeout cancellazione automatica credito residuo
FW v. 1.19
Rev. 1.04
29.04.16
Inserito lettore ACS
FW v. 1.23
Rev. 2.00
07.03.19
Uniformato manuale con edizione italiana
FW v. 1.26

4
Please read carefully this handbook, to obtain the most from your machine.
Dear Customer,
we would like to thank you and congratulate for your choice. We trust that you will appreciate the
quality and performace of the HIRA ONE automatic Change Machine.
This machine operates by cctalk protocol, the well-established serial communication mode that
provides security and precision.
1. Package content
The package contains:
1. the Alberici HIRA 2 / Hira 2 Maxi Change machine
2. 1 pair of keys
3. the power cable (see inside of money box)
4. the instruction manual (this manual)
This product has been packed with the utmost care. In the case that you receive it damaged or
incomplete, please notify immediately your findings to the Carrier.
2. Components description
E
A
D I
C
L
G
M
F
H B
POS.
COD.
DESCRIZIONE
A
A-CM0249
Power Switching box RD-125
B
SH-1A21
ChangeOne CMS board
C
S-020933-000
3 blue-led bar
D
K-02C-020070
2 x HopperOne S11 ccTalk STD
E
AA-0309
AA-0315
AA-0333
SECTOR 100 capacity extension (HIRA 2 Mini)
SECTOR 300 capacity extension (HIRA 2 Midi)
SECTOR 100 capacity extension (HIRA 2 Maxi)
F
LB-LU01-0004
or else:
LB-MU02-0004
BillyOne ccTalk note validator
or else:
OryOne ccTalk (stackered) note validator
G
PL-MK21-ET6H
Halo quick-fix square 21 RGB pushbutton
H
AM-1509
Flat key lock L=21mm keyed different
I
AM-1305, else
HR1-011A-P00
Plastic “A” coinbox, or else
Metal coin box
L
GE-66SC
AL66S coin acceptor
M
IM-N000-0L10
PP coin entry slot

5
3. Product description
3.1 General data
Technical specs:
HIRA 2
Size:
Weight:
Voltage:
Nominal power:
Operation temperature:
Installation:
Coin capacity:
Components:
Power supply unit
Control board
Note validator
Pay-out Hopper
Coin acceptor (optional)
Remote audit (optional)
See page 6
Mini: 30 Kg (50 with floorstand) - Midi: 39 Kg (59 Kg with floorstand) –Maxi:35 Kg
(55 with floorstand)
230 Vac - 50 Hz
340 W max
0°C ÷ +50°C
Desktop or on floorstand or wall-mount, indoor
Mini: 4000 - Midi: 5600 - Maxi: 7200
Power switching 340W
CHANGEONE CMS with DISPLAY LCD 2x16
BILLYONE, or else: ORYONE (stackered)
2 x HopperOne S11 or AH4 (also together)
AL66S cctalk
Alberici GSM-GPRS or GPS/GSM/GPRS (*)
Notice: Euro is the preset currency. If you require a different currency, please request your
currency before placing your order.
(*) The system requires a SIM card enabled for data traffic, and the subscription to the Portal ARGO if you want to
control the machine via the Internet, or a SIM card enabled voice traffic / messages and data traffic if you only want to
use SMS messaging. It is recommended to check carefully that the SIM card functions properly in the area.
3.2 Available functions
- Change of notes and coins into 1 denomination coins, or 2 denominations at User’s choice
- Change of notes and coins into 1 denomination tokens, or 2 denominations at User’s choice
- Control of accounts via display (by on-board keys)
- Programmable via menu (by on-board keys)
- Change of display language by external “SEL” pushbutton, at User’s choice.
4. Warning
- Comply with the instructions in this manual
- Switch power off before any maintenance operation
- Use only within the recommended temperature/humidity range
- Do not expose the machine (and especially the mote acceptor front plate) to direct
sun light or to incandescent light (> 3000 Lux)
- When in precence of car exhaust gas or smoke, clean and check the components (the note acceptor
in particular) regularly and frequently.
- Do not favour contact with dusts or chemical moisture or sprays, water or other liquids
- Instal indoor
- Wipe clean by a dry piece of cloth (or slightly wet withalcohol)
- Do not use thinners or organic solvents
- The note acceptor could reject (or get jammed by) stained notes, or worn out, wet, wrinkled, torn,
dog-eared, oil-smeared, with sticking tape or similarly affected.
- Clean monthly the sensors of the note acceptor. Remove paper dust that has accumulated on the
drive wheels, by a clean piece of cloth or a cotton swab. Do not use alcohol nor solvents or scrapers.
!

6
Maxi
Midi
5. Installation
PAY ATTENTION: IT IS ESSENTIAL TO FASTEN THE MACHINE TO A
SOLID WALL BY USING RELIABLE EXPANSION BOLTS.
IT IS RECOMMENDED THAT YOU MAKE USE OF THE WALL-MOUNT
SLAB (ref. HRP-021A-V06 for HIRA 2 Mini, HRM-AM15-V06 for HIRA 2
Midi, HRS-015A-V06 for HIRA 2 Maxi) .
All measures in mm
Put the Change Machine in place and fasten it
to the wall by expansion bolts through the “x”
holes in the rear side of the cabinet. Keep the
on-off switch accessible. In addition, the
machine can be secured to the floor: the large
holes at the foot allow to secure the machine
by a binding chain.
The fastening slab allows to easily secure the
machine to the wall.Once fixed the slab to the
wall, the machine can be either fastenedto it
by screws (“Z” holes), or just hung upon the
slab’s hooks,so as to remove it at ease.
!
Mini

7
WALL-MOUNT SLABS:
HRS-015A-V06 for HIRA 2 Maxi
430
Preparethetunnelforthe
power cable in the wall
(corresponding to “Y”
Holeintheslab).
Fasten the slab to the
wall by sturdy expansion
bolts, through the 6
“X” (12 mm) holes.
Connectthecabletoitssocketbehindthe
machine,andhangthelatteronthe4“W”
supportinghooks.
FixthemachinetotheslabbyM8screws
throughthethree“Z” threadedholes,ifyou
donotplantooftenremoveandre−hang
themachine uptoits”y” hooks.
HRM-AM15-V06 FOR HIRA 2 MIDI
430
Preparethetunnelforthe
power cable in the wall
(corresponding to “Y”
Holeintheslab).
Fasten the slab to the
wall by sturdy expansion
bolts, through the 6
“X” (12 mm) holes.
Connect the cable to its
socketbehindthemachine,
andhangthelatteronthe4
“W” supportinghooks.
FixthemachinetotheslabbyM8screws
throughthetwo“Z” threadedholes,ifyou
donotplantooftenremoveandre−hang
themachine uptoits”y” hooks.
250
40
40
Y
Y
X
X
Y
W
Z
40
135
215
12
Z
X
X
340
135
135
X
X
Z
80
80
140
250
40
40
X
X
Y
W
Z
40
135
215
12
X
X
340
135
135
X
X
Z
80
80
140
135
135
45
430
430
45
45
45
40
40
45
45
70
70
70
220
250
220
250
70
625
760

8
HRP-021A-V06 FOR HIRA 2 MINI
430
Preparethetunnelforthe
power cable in the wall
(corresponding to “Y”
Holeintheslab).
Fasten the slab to the
wall by sturdy expansion
bolts, through the 6
“X” (12 mm) holes.
Connectthecabletoitssocketbehindthe
machine,andhangthelatteronthe4“W”
supportinghooks.
FixthemachinetotheslabbyM8screws
throughthetwo“Z” threadedholes,ifyou
donotplantooftenremoveandre−hang
themachine uptoits”y” hooks.
PREPARATION FOR USE:
PAY ATTENTION: FILL THE HOPPERS ONLY WHEN THE MACHINE IS OFF
Open the door and locate extensions capacity on top of the hopper.
Unlock the latch A (white slide) of the cover and slide
the latter fully out towards the outside, until is positioned
as a pilot chute: pour into the hopper the coins or tokens to
be dispensed as change.
Unlock again the latch A and slide the cover back
to “closed” position.
Close the tiltable front flap of the machine.
Plug the power cable in, and turn the main switch on.
Component check and self-setting shall start automatically. At the end, a message will inform that
the machine is ready for operation, showing what coin(s) (tokens) value(s) will be paid in exchange
for notes and coins introduced, as well as a welcome wording.
This message takes shifts with:
As soon as the control board enables the note acceptor, the latter’s front slot flashes once in blue
colour for each enabled note, or once in red for each disabled note. For instance, if the 5, 10, 20
Euro notes are enabled, and the 50 and 100 Euro notes are disabled, the front slot will flash 3 times
in blue colour and 2 (twice) in red.
The machine is now ready to operate.
A
250
40
45
X
X
Y
W
Z
350
40
X
12
X
270
X
X
Z
80
140
EROGA MONETE
DA
1,00 € - 2,00 €
CHANGEON
E
Promo
120
50
45
40
60
45
70
180
470

9
6. Operation
Three buttons are available: “1” and “2” allow the User to choose the coin (or token) denomination
he wants back as change; third button allows the user to choose the language he wants on the
display (English, French, German, Italian and Dutch are available. Ask before placing order for
other languages options). This type of operation varies depending on whether the operation mode is
set to AUTOMATIC or to MANUAL.
6.1 AUTOMATIC MODE -when a note or coin is inserted, the credited amount is displayed, and
the control board starts the pay-out by the hopper(s). The machine combines the coins contained in
the hoppers. If the machine is set to Tokens+Change, all the tokens that can be bought by the
inserted sum will be dispensed, with the back change in addition. At the end of the payout cycle,
the display will show both the inserted amount as well as the amount paid out.
6.1.A PAY-OUT ENABLED AND PROGRAMMED: whenever a note or coin is inserted, the display
shows the credited amount, and the the pay-out shall take place according to the combination that
the Operator has pre-programmed for the amount inserted (see section 7.3.6.3 A).
6.2 MANUAL MODE - when a note or coin is inserted (or when the value of one token is reached),
the button(s) will lit up green . Press the button corresponding to the change (token) desired. If the
machine is set to Tokens+Change, it will be possible to choose the desired number of tokens.
If the machine is set to Tokens or to Tokens+Change, and the Bonus has been set, introduce money
until the searched amount is reached, then press the OK button.
WARNING: If there are not enough coins in the hopper to fulfil the whole exchange request, the remaining credit shall
be displayed and retained in memory. Switch off the machine, fill the hoppers, and switch on again: the remaining
credit shall be paid out.
An option is to set the Menu (see section 7.3.14) so as to cancel the remaining credit - and at the same time
record it in the Accounts menu - by switching the machine off and on again.
7. System configuration
7.1 Default configuration
The HIRA 2 Maxi is preset by default as follows (unless requested for different setup):
Control Board Parametres Pay-out mode = AUTOMATIC
Bonus = DISABLED
Level sensors = DISABLED
Hopper S11 Parameters Hopper nr. 1 (*) = € 2.00 = ENABLED
Hopper nr. 2 (*) = € 2.00 = ENABLED
Hopper AH4 discriminator [ccTalk] Preset by default to 0,50 –1,00 –2,00 €
BILLYONE Validator [ccTalk] Parameters € 5.00 - …. - € 100.00 = ENABLED
AL66 S [ccTalk]coin acceptor Parameters € 0.05 - € 0.10 - € 0.20 = DISABLED
€ 0.50 - € 1.00 - € 2.00 = ENABLED
7.2 Restore default configuration
If any variation is made, it will be possible to restore the default configuration as follows:
enter the initial menu, scroll by UP and DOWN keys and choose RESTORE DEFAULT CONFIGURATION
then press OK; the message DEFAULT CONFIG. RESTORED will be displayed.
NOTICE: the RESTORE DEFAULT CONFIGURATION command resets the default PIN code (0000) .
(*) The Hopper 1 (primary) is placed at the left side (watching the
machine from the front); Hopper 2 (secondary) is placed at the right side.
Set Dip-switches in HP1 to address 3 (all DS to OFF)
Set Dip-switches in HP2 in HP2 to 4 (no. 1=ON, nos. 2= 3=OFF).

10
7.3 Menu functions
7.3.1 Surf the Menu:
To enter the menu and navigate it, make use of the 3 keys located on the board rear side.
CMS board
Rear view
Get access to the menu by holding the three buttons pressed at the same time for 5 seconds.
OK confirm selection
+ - navigate menu UP and DOWN; modify figures andletters
REG adjust display brightness
PWR IN POWER IN
24 12 GND
CC12
PWR OUT
CCT 24
RGB1
RGB2
RGB3
COIN ACCEPTOR AL66
NOTE ACCEPTOR
HOPPERONE S11
ILLUMINATED PUSHBUTTONS: RGB1 = SELECT RGB2 = CONFIRM RGB3 = LANGUAGE
24 12 GND
REG
P4/7 RGB3 RGB2 RGB1 SP1 CC12
PWR
IN
PWR
OUT
CCT
24
TST
PT
STP
OK
-
-
+
+
PROG

11
BONUS
7.3.2 MENU MAIN STRUCTURE
(*)
(*) only available with HopperOne,
and only if preset for:
DISPENSING MODE = TOKENS
MANUAL REFILL
SETUP
EMPTY OUT
HOPPER
SHOW
ACCOUNTS
CHANGEONE
Promo
SHOW
PERIPHERAL
UNITS
EXIT
MENU
PERIPHERAL
UNITS SET UP
EXIT
MEN
U
ENABLE./DISABLE
REMAINING
CREDIT
LANGUAGE
SETUP
MODIFY PIN
PROMO
RESTORE DEFAULT
CONFIGURATION
RESET
ACCOUNTS
Notice: PIN is requested
to access some sub-menu
settings.

12
All Totals
cancelled
Enter
PIN
0
7.3.3 Show peripheral units
This menu allows to check the state of the PERIPHERAL UNITS, for instance:
7.3.4 Show accounts
This menu allows to check the total and the partial values of cashed and paid amounts.
(*) Reset of the remaining credit: see section 7.3.14
- Press OK: the display will show the total amounts introduced (TOTAL IN). Press UP, and OKif
you want to exit the ACCOUNTS menu.
- Or else, press DOWN to check the total amounts dispensed (TOTALOUT).
- Press DOWN to go on browsing the submenu.
Notice: whenever the Partial Amounts record get cancelled (see section 7.3.5), the previous value recorded in “Last
Partials cancelled” gets replaced by the amount that has just been reset.
LAST AMOUNT DISPENSED: when the board is in stand-by condition, it is possible to check the last amount
dispensed, by holding the SELECT pushbutton for full 4”.
7.3.5 Reset accounts
To use this sub-menu it is necessary to digit the PIN code. This function allows to cancel the
account records (both paid out and cashed in) of the machine.
For each of the 4 digits of
thePIN, use UP and DOWN to
highlight the figure wanted, then
confirm by OK. At the end, the
display will show:
Once entered the PIN,
the display will show:
(*) Whenever the Partial Amounts records get cancelled (see
section 5.4), the previous value recorded in “Last Partials
cancelled” gets replaced by the amount that has just been reset.
(*)
Reset
Partial Amounts
Exi
t
COIN ACCEPTOR
DISCONNECTED
HOPPER 1
EMPTY
NOTE VALIDATOR
CONNECTED
SHOW
ACCOUNTS
RESET
ACCOUNTS
RESET
ACCOUNTS
(*)
Remained Credit
Paid 00,00 €
00,00 €
00,00 €
IN:
OUT:
All Partials
cancelled
Exi
t
Reset
Total
Amounts
Exit
Cashless Total
00,00 €
Last partials
cancelled
Partials out
00,00 €
Partials in
00,00 €
Total out
00,00 €
Total in
00,00 €

13
Set up Hopper 1 :
1,00 €
7.3.6 SETTING THE PERIPHERAL UNITS
This menu allows to set up the denominations accepted by the note validator and by the coin
acceptor, as well as the value of the coins/tokens dispensed. It also permits to set the change mode
as either automatic or manual, and to enable/disable the full/void sensors of the hoppers.
(*)
(*) Press Down or Up
to modify amounts in
discreet steps of 0,05
€ each
7.3.6.1 NOTE VALIDATOR SETUP
See section 7.3.6.3a for the next steps in setting up
the Pay-Out Table special function
The board automatically detects the presence of the note acceptor during initial check. All the
programmed note values (5-to-100 Euro) get automatically enabled. To modify this default
condition, press OK to get to the first option (ex. 5 €) and highlight it, then press UP or DOWN to
reverse its state. Press OK to shift to the next option (ex. 10 €).
5 10 < 20 > 50 100
OK OK OK OK OK
5 < 10 > 20 50 100
OK OK OK OK OK
PERIPHERAL
UNITS
SETUP
EMPTY OUT
HOPPERS
Set up
Cashless
Set up
Dispense mode
Set up
COINS
Set up
TOKENS
Set up
TOKEN + CHANGE
Set up TKN/CH?
Disable
Set up
Tok/Change
Enable
<LEV1 HP1 HP2>
0,00€ 0 0
Set up
Note validator
< 5 > 10 20 50 100
NO OK OK OK OK
< 5 > 10 20 50 100
OK OK OK OK OK
0,50
OK
OK OK
< 2,00 > 1,00
OK
NO
1,00 < 0,50 >
2,00
OK
Level sensors
disabled
Dispensing mode
AUTOMATIC
Dispensing mode
MANUAL
Level sensors
enabled
Set up Hopper 2 :
0,50 €
2,00 < 1,00> 0,50
NO OK OK
< 2,00 > 1,00 0,50
NO OK OK
Set up
Coin
acceptor
Set up
GSM / GPRS
2,00 < 1,00 > 0,50
OK OK OK
< 5 > 10 20 50 100
NO OK OK OK OK
5 < 10 > 20 50 100
NO OK OK OK OK
< 5 > 10 20 50 100
OK OK OK OK OK
Set up
Note
validator
Exi
t
5 10 < 20 > 50 100
OK OK OK OK OK
5 < 10 > 20 50 100
OK OK OK OK OK

14
Set up
TOKENS+CHANGE
Exit
<LEV1 HP1 HP2>
0,00€ 0 0
Set up TKN/CH?
Disable
Level sensors
disabled
Set up Hopper 1:
1,00 €
7.3.6.2 COIN SELECTOR SETUP
The board automatically detects the presence of the coin selector during initial check. Among the
accepted coins (0.05-to-2 €), the following ones get enabled by default: 0.50 € - 1.00 € - 2.00 €.
To modify this condition, press OK to get to the first option (ex. 2 €) and highlight it, then press UP
or DOWN to reverse its state. Press OK to shift to the next option (ex. 1 €).
7.3.6.3 DISPENSING MODE SETUP
Allows to choose whether to dispense COINS or TOKENS or TOKENS+CHANGE, and whether the
DISPENSING MODE will be AUTOMATIC or MANUAL.
It also permits to monitor the level of the coins in the hopper(s) by the electronic sensors.
(*) Use keys Down and Up to modify
values. Max. value for tokens: 12,70 €.
(*)
7.3.6.3.A PAY-OUT TABLE
When the Pay-out Table is enabled, the Operator can configure 8 different combinations of change,
each of them related to the amount introduced by the User.
The LEVEL box can be set to a determined amount (typically, the accepted coin and note
denominations), while the relevant HP1 and HP2 values can be set to:
- number of pieces so that their calculation sums up to the amount set in the LEVEL box, if change
in cash is handled;
- any desired value, if Tokens only will be handled -this will allow for awarding bonus as well;
- any consistent combination, if Tokens and return change will be handled.
When choosing to enable the Pay-Out Table, the display will prompt you to set the payout
combination for the first level available (LEV1). To set it up, highlight LEV1 by “OK” and set its
value by the “+”button, then confirm by “OK”. The cursor will shift to the HP1 box: confirm by
“OK”, and set its value by the “+” button (modify by “-“), then confirm by “OK”, and do the same
for HP2. When confirming the value in HP2, the chosen combination for LEV1 will be shown.
Step from LEV1 up to LEV2 by “+”, highlight LEV2 by “OK”, and repeat above process.
Set up
Coin
acceptor
2,00 1,00 < 0,50 >
OK NO OK
OK
OK
< 1,00 > 0,50
2,00
OK
0,50
OK
< 2,00 > 1,00
OK OK
Level sensors
enabled
0,50
OK
< 2,00 > 1,00
NO OK
Set up
TOKENS
(**)
Set up Tok/Change?
Enable
(*)
Set up Hopper 2:
0,10 €
Dispense mode
MANUAL
Dispense mode
AUTOMATIC
Set up
COINS
SET UP
DISPENSING MODE
(*)
Token
or Coin?

15
<LEV1 HP1 HP2>
0,20€ 0 2
OPERATION AFTER SETTING THE PAY-OUT TABLE:
when the User will insert money corresponding to any of the programmed levels, the machine shall pay out the
combination of pieces that the Operator has pre-programmed for the amount inserted by the User (see section 6.1.A).
SETTING THE PAY-OUT TABLE:
Let us assume that HP1 has been set to 1 €, and that HP2 has been set at 0,10€.
Press OK when prompted by the message “Set up Tok/Change?Enable” to
confirm that you want to set the Pay-out Table. Level 1 will be shown:
LEVEL 1: Press “OK”, then by the “+” key set LEV1 to the first denomination that you want to accept, for instance
0,20€. Confirm by “OK”; the display will automatically set HP2 = 2, i.e. two 0,10€ coins would be paid against 0,20€.
Confirm until Take care: “<LEV 1 HP1 HP2>”, not “<LEV1> HP1 HP2” !
you get: PRESS “+” FOR LEVEL 2 (or PRESS REPEATEDLY “+” TO EXIT).
LEVEL 2: By “OK”, confirm LEV2. By “+”, set LEV2 to 0,50€ and confirm. HP2 will automatically set to 5 pieces.
Confirm until “ <LEV 2 HP1 HP2>” (not “<LEV2> HP1 HP2” !) shows again.
PRESS “+” FOR LEVEL 3 (or PRESS REPEATEDLY “+” TO EXIT).
LEVEL 3: By “OK”, confirm LEV3.
By “+”, set Level 3 to 1,00€ and confirm. HP1 will automatically set to 1 piece (1€).
By the “-” button, change HP1 to 0 and press OK; by the “+” button, set HP2 to 10 (10x0,10€)
Confirm until <LEV 3 HP1 HP2> shows again. PRESS “+” FOR LEVEL 4 (PRESS REPEATEDLY “+” TO EXIT).
LEVEL 4: By “OK”, confirm LEV5.
By “+”, set Level 4 to 2,00€ and confirm. HP1 will automatically set to 2 pieces (2 x 1€).
You can set the pay-out table so as dispense any of the following combinations: (A) 2x1€ coins, or (B) 1x1€ + 10x0,10€
coins, or else (C) 20x0,10€ coins.
Suppose choosing the combination (C): by the “-” button, change HP1 to 1 (1x1€ coins) and press OK.
By the “+” button, set HP2 to 10 (10x0,10€)
Confirm until <LEV 4 HP1 HP2> shows again. PRESS “+” FOR LEVEL 5 (PRESS REPEATEDLY “+” TO EXIT).
LEVEL 5: By “OK”, confirm LEV4.
By “+”, set Level 5 to 5,00€ and confirm. HP1 will automatically set to 5 pieces (5 x 1€).
You can set the pay-out table so as dispense any of the following combinations: (A) 5x1€ coins, or (B) 1x1€ + 40x0,10€
coins, or (C) 2x1€ + 30x0,10€ coins, or (E) 3x1 + 20x0,10€ coins, or (F) 4x1 + 10x0,10€ coins, or else (G) 50x0,10€.
Suppose choosing the combination (F): by the “-” button, change HP1 to 4 and press OK; by the “+” button, set HP2 to
10 (10x0,10€)
Confirm until <LEV 5 HP1 HP2> shows again. PRESS “+” FOR LEVEL 6 (PRESS REPEATEDLY “+” TO EXIT).
LEVEL 6: By “OK”, confirm LEV6.
By “+”, set Level 6 to 10,00€ and confirm. HP1 will automatically set to 10 pieces (10 x 1€).
You can set the pay-out table so as dispense any of the following combinations: (A) 10x1€ coins, or (B) 9x1€ +
10x0,10€ coins, or (C) 8x1€ + 20x0,10€ coins, or ….. (N) 5x1 + 50x0,10€ coins, and so on.
Suppose choosing the combination (B): by the “-” button, change HP1 to 9 and press OK; by the “+” button, set HP2 to
10 (10x0,10€).
Confirm until <LEV 6 HP1 HP2> shows again. PRESS “+” FOR LEVEL 7 (PRESS REPEATEDLY “+” TO EXIT).
LEVEL 7: By “OK”, confirm LEV7.
By “+”, set Level 7 to 20,00€ and confirm.
You can set the pay-out table so as dispense any of the following combinations: (A) 20x1€ coins, or (B) 19x1€ +
10x0,10€ coins, or (C) 18x1€ + 20x0,10€ coins, or … (M) 16x1€ + 40x0,10€, or ... (N) 5x1 + 50x0,10€, and so on.
Suppose choosing the combination (M): by the “-” button, change HP1 to 16 and press OK; by the “+” button, set HP2
to 40 (40x0,10€).
Confirm until <LEV 7 HP1 HP2> shows again. PRESS “+” FOR LEVEL 8, OR PRESS OK UNTIL EXITING.
NOTICE: monitoring of level sensors is disabled by default. This means that the board does not know when the hopper
is empty, so it will send the pay-out command even if there are no coins available. When the hopper runs out of coins
during dispensing or at the end of payment, no warning will be displayed. If the empty state is detected when powering
the unit, this one shall not accept any money.
If instead the monitoring has been enabled, and there are not enough coins in the hopper, the display will warn that the
hopper is empty. There will usually remain 20 coins approximately, so as to complete the change payout.
PLEASE PAY ATTENTION: if the machine must be re-configured from token (or token+backchange)
dispenser to coin changer, always do reset to DEFAULT CONFIGURATION and RESET ACCOUNTS. Else, the bonus
setting could produce Accounts inconsistency.
<LEV1> HP1 HP2
0,00€ 0 0

16
DISPLAY
A CCOUNTS
(*)
DISPLAY LAST
EVENT
(*)
DATE AND TIME
CASH
WITHDRAWAL
KEYS
WITHDRAWAL
Master key only
RESTRICTED MENU
Key
initialized!
Antenna
initialized!
Enter PIN
0
7.3.6.4 SET UP CASHLESS (only if the ACS reader is built-in)
If the unit is equipped with the ACS reader, it is possible to get access to useful functions:
Operation
Master Key (black)
for the owner
Service Key (white)
for the manager
Operator Key
(yellow)
1. Inizialize Service and Operator keys
YES
YES (only Operator’s)
NO
2. Enable white key to collect money
YES (from Menu)
NO
NO
3. Check Accounts (totals and partials)
YES
YES (partials only)
NO
4. Print Accounts
YES
NO
NO
5. Reset Accounts Data (all)
YES
YES (partials only)
NO
6. Reset of paid residual credit
YES
YES
NO
7. Access to (optional) manual Refill
YES
YES
NO
8. Access to automatic Refill and accounts
YES
YES
YES
9. Collect money if key is enabled and loaded
YES (max 500€)
YES (max. 200 €)
NO
The Master key allows to initialize the Service and the Operator Key from the ACS reader.
Whenever the Master Key or the Service Key gets access to the Accounts menu, the shown data get
automatically downloaded in the key. Each key can contain up to 10 downloaded sets. These data
sets can be read and stored in the PC via the ACR Programming Station (K-P4N-000007) and software.
When entering this menu, the display will request to initialize the key reader (antenna). Work out
one 6 digits PIN code, write it down and keep it in a safe place.
Insert the Master key and press the OK button: you will be prompted
for entering the PIN code. Insert the 6 digits PIN. To enter each of the
6 digits, make use of the UP and DOWN buttons. When the desired
character is displayed, confirm it by the OK button.
After entering the 6th character, the display will prompt for confirming the PIN code. Enter it again:
initialization of the key reader and of the Master Key will start.
When finished, the confirmation message appears (see beside):
Insert now the Service key: the machine 4-digit pin code (see section 9.3.13 Change PIN) will be
requested; enter it to get the Service key initialized.
Once the process is complete, the confirmation message appears:
To initialize the Operator key, exit the menu, put the Master key or the Service key in the reader,
and navigate the menu by “+” until finding RESTRICTED MENU: press OK, and navigate again until
INITIALIZE KEYS, then press OK. Insert the Operator key and follow the instructions appearing:
Insert Operator Key
(yellow)
Wait…… Remove the
initialized key
7.3.6.4 b Restricted menu (reserved to owners of Master Key and of Service key)
When inserting the Master or the Service key in the reader, the pushbuttons SEL and OK light up
green. By touching SEL, it is possible to navigate the following options: Accounts, Restricted
Menu, Exit.
By SEL, navigate to: and press OK. The following functions will be available:
INITIALIZE
(**)
(***)
ENABLE CASH
(*) Reserved to
(**) Master can create Service and Operator
Keys; Service can create Operator Keys
(***) Reserved to Master only,
enabling Service Key only
Key
initialized!
Do not remove the
key
Init. Operator
Key

17
Please wait
…….
Test GSM / GPRS
Module
(*)
Insert User Code:
A
Insert User Code:
UC123CUH45
Set
User Code
GSM / GPRS Module
Test in progress
GSM / GPRS Module
In service
Please wait
…….
7.3.6.5 SET UP GSM/GPRS
When the GSM/GPRS kit is installed, it gets detected during self-configuration, and its parameters
must be set up for operation.
(*)By buttons “+” and “+” , locate the letter/digit, and OK button to confirm your choice; the cursor will automatically move to the
next character. There are 16 characters in the machine name, and 10 for the User Code (the latter is needed only for the Argo Web
Portal). After confirming the last character, the name you have typed gets automatically saved.
(**) By buttons “+” and “+” , locate the number you want to write, and press OK to confirm it; the cursor will automatically move
to the next character. Once having confirmed the last digit, confirm as well the whole number entered: you will be prompted to enter
the second number, and finally the third.
(*)
Insert Name:
A
Set
Name of Machine
(***)
Enable/Disable
Service status
(***)
Enable/Disable
Remote payment
(****
Set
Security level
Security level
High?
Remote payment
Disabled
Service status
Disabled
Security level
Low?
Remote payment
Enabled
Service status
Enabled
(**
Cellphone Nr [1]:
>_<
Insert name:
LUCKY HALL
Please wait …….
Please wait… saving
Set up
GSM/GPRS
Exit
Cellphone Nr [2]:
>_<
Cellphone Nr [4]:
>_<
Cellphone Nr [1]:
>+39347nnnnnnn<
Set enabled
Cellphone Nrs.

18
total
nnn,nn €
total
nnn,nn €
Exi
t
EMPTY
HOPPER 2
EMPTY
HOPPER 1
EMPTY OUT
HOPPERS
LEV EURO PCS
2 10€ 11
LEV EURO PCS
1 2..3..10 €1
(***) When the Service Status Remote Enable function is active, the machine can be put out of service by sending an SMS (text is
“CMD=OFF”) from any of the 3 enabled cellular phones. To restore service, send text “CMD=ON”.
(****)When the Remote Payment function is active, and the Security Level has been set to Low, it is possible to command the
machine to dispense an amount (in €) or a number of tokens (pieces) by sending the following sms text from any of the 3 enabled
cellular phones:“OUT=n°” (n° = any value between 0 and 250).
When the Remote Payment function is active, and the Security Level has been set to High, it is possible to command the machine to
dispense an amount (in €) or a number of tokens (pieces) by sending the following sms text from any of the 3 enabled cellular
phones:“OUT=n°:1234” (n° = any value between 0 and 250; 1234 = any combination of figures except 0). ). In this case, the
display will prompt for the password: the User will then put the Refill key in the Refill lock (or the RFID key in its reader), and then
enter the password by using the buttons SEL (select each number) and OK (confirm each number).
7.3.7 Empty out the Hoppers
Use this function to make the selected hopper pay out all the contained coins / tokens. Once emptied
the first hopper, total dispensed amount shall be displayed. Press OK to go on with second hopper.
7.3.8 Restore default configuration
To use this sub-menu it is necessary to digit the PIN code.
WARNING: in case of reset, the system sets back to default configuration. The PIN code will be
reset to the default 0000 setting. Account records shall not be cancelled.
7.3.9 Bonus Set Up
This function will operate only if at least the hopper nr. 1 is preset for paying tokens. Take care to
set up all hoppers parameters. Bonus function is disabled by default.
(*)Use Up key to modify
values
(*)
NOTICE: in case of any
mistake, do confirm the
wrong programmed data,
then re-program correctly.
PLEASSE WAIT
……….
Enter PIN
0…
RESTORE DEFAULT
CONFIGURATION
BONUS
Bonus
ENABLE?
LEV EURO PCS
0 1€ 1
LEV EURO PCS
1 1€ 1
(*)
LEV EURO PCS
1 10€ 11
LEV EURO PCS
1 11..12.. €1
LEV EURO PCS
2 10€ 11
LEV EURO PCS
1 10€ 1
Bonus
DISABLE?
Bonus settings
stored

19
7.3.10 Language setup
7.3.11 Promo
It is possible to preset an advertisment on the display. Press OK:
Press again OK, the pointer will highlight the first digit: by UP or DOWN, choose the character that
you want to insert, then confirm by OK. The pointer will highlight the following digit.
Once digit nr. 16 has been confirmed, the message gets stored.
7.3.12 Modify PIN
The PIN code allows to get access to the discretional menus of the system.
The PIN code is made up by 4 figures (each of them from 0 to 9: 10,000 combinations available).
If the entered PIN is not correct, the User is given another 4 tries before the board gets blocked-up
by its security interlock. The system can be started again by switching it off and on again.
ATTENTION: the default PIN code is 0000
The settings in the following menus can be modified by using the PIN code:
MODIFY PIN - RESET ACCOUNTS - RESTORE DEFAULT CONFIGURATION
To modify the existing PIN, press OK, and digit the old PIN code: to digit each code figure, first
use keys UP and DOWN to set each figure, then confirm it by OK. Once the 4th figure has been
confirmed, confirm by OK the whole old PIN:
To enter the new PIN code, use first the UP and DOWN keys to set each figure, then confirm it by
OK. Once the 4th figure has been confirmed, confirm by OK the whole new PIN.
As every single figure gets confirmed, an asterisk takes its place, so preserving secrecy.
NOTICE: when DEFAULT CONFIGURATION is restored, the PIN code gets reset to 0000.
LANGUAGE
SETUP
Seleziona lingua
ITALIANO
Choose language
ENGLISH
Waehlen Ihre Sprache
DEUTSCH
Digit text
-----------------------
-
New PIN
0
Enter
PIN
0
MODIFY PIN

20
+ / -
+ / -
Totale importo
Caricato: 2500€
Warn at 1
Euro available
+ / -
+ / -
Warn at 200
€ / Pcs available
Warn at 100
Euro available
MANUAL
REFILL
Confirm?....
MANUAL
REFILL
Confirm?....
E
M
P
T
Y
H
O
P
P
E
R
S
MANUAL REFILL
SET UP
MANUAL REFILL
SET UP
Reset of R
TURN OFF / ON
DELAYED
DISABLED
ENABLE / DISABLE
REM. CR. RESET
7.3.13 Manual Refill Set Up
Refill can take place when unit is empty or not. Allows to record the amount put in.
(*) Shows “€” when set
for coins
Shows “Pieces” when
set for tokens
7.3.14 Enable / Disable remaining Credit
Amount of remaining (i.e. unpaid) credit can be reset when machine is switched off. Such amount
gets automatically recorded in the Accounts (sez. 7.3.4).
emaining Cr. + / -
(*)
Reset of Remaining Cr.
Reset of Remaining Cr.
(*) When enabling this option, the remaining credit shall be cancelled within 15 seconds from end of transaction.
7.3.13 Exit Menu
Press OK to go back to stand-by condition:
Totale
available:
€ / Pcs
1800€
Warn at 50
€ / Pcs available
EXIT MENU
Exit Menu
in progress…
CHANGEONE
Promo
Enter filled
Amount: 1€
Total
available:
(*)
€ / Pcs
1€
H
O
P
P
E
R
S
N
O
T
E
M
P
T
Y