PREPARATION FOR USE:
PAY ATTENTION
:
FILL THE HOPPERS ONLY WHEN THE MACHINE IS OFF
.
Open the door and locate extensions capacity on top of the hopper.
Unlock the latch A (white slide) of the cover and slide
the latter fully out towards the outside, until is positioned as
a pilot chute pour into the hopper the coins or tokens to be
dispensed as change.
Unlock again the latch A and slide the cover back
to “closed” position.
Close the tiltable front flap of the machine
.
The coin denomination preset for all the single-coin hoppers is € 2. When the machine is equipped with banknote
recycler, the two default denominations for the recyclable banknotes are € 50 and € 20. It is possible to modify
such default configuration through the setting menu see section 7.3.6.2.
Plug the power cable in, and turn the main switch on. The ON/OFF switch is located by the side of the mains
cable socket, on the back side of the machine.
The system shall start automatically self-check and the self-setting. At the end, a message will inform that the
machine is ready for operation, showing what coin(s) (tokens) value(s) will be paid in exchange for the notes and
the coins introduced.
The change machine will activate different procedures depending on whether it has been set up to operate by
the AUTOMATIC MODE (factory setting) or in MANUAL MODE.
When set to standard Automatic Mode, the machine will pay-out a balanced combination of the denominations
(pieces) contained in its hoppers, against paid-in cash. Else, the Operator can enable and program the Pay-out
Table in which, for each of 6 programmable pay-in levels, he will be able to program 1 combination of the
amounts paid out by each hopper, according to his convenience (see Section 7.3.6.3 A).
When set to standard Manual Mode, the User will be able to choose the desired denomination. Else, the
Operator can enable and program the Pay-out Table in which, for each of 9 programmable pay-in levels, he will
be able to program up to 3 pay-out combinations of the amounts paid out by each hopper, according to his
convenience the User will be able to choose among such 3 combinations (see Section 7.3.6.3 B).
To allow the User to buy Tokens by POS card, the POS Pay-out Table must be programmed in which, for each
of 10 programmable pay-in levels, 3 pay-out combinations of the amounts paid out by each hopper can be set,
according to the Operator’s convenience the User will be able to choose among such 3 combinations (see
Section 7.3.6.3 C). The POS works in this way whichever Mode (Manual or Automatic) the machine is set up to.
AUTOMATIC MODE MANUAL 2P MODE POS MODE
For each inserted amount out of 6
programmable levels (to be chosen
among 0,10 - 0,20 - 0,50 – 1 - 2 - 5 -
10 – 20 - 50 - 100 €), the User will
receive the relevant combination of
Tokens/Coins preset by the Operator.
If the note recycler is present, the User
will receive the preset combination of
Tokens/Coins and Banknotes.
For each inserted amount out of 9
programmable levels (to be chosen among.
0,10 - 0,20 - 0,50 – 1 - 2 - 5 - 10 – 20 - 50 -
100 €), the User will be able to choose among
3 combinations of Tokens/Coins preset by
the Operator.
If the note recycler is present, the User will be
able to choose among 3 preset combinations
of Tokens/Coins and Banknotes.
For each inserted amount
out of 0 programmable
levels (to be chosen
among. 0,10 - 0,20 - 0,50 –
1 - 2 - 5 - 10 – 20 - 50 -
100 €), the User will be
able to choose among 3
combinations of Tokens
preset by the Operator.
CHANGE
DISPENSING
2,00€
1,00€
0,50€
0,10€
INSERT
COINS / BANKNOTES
or
PRESS SEL FOR CARD
