Alecto AQ30 User manual

ENVIRONMENT:
Do not dispose of spent batteries but return them to your local depot for
Small Chemical Waste (MSW). At the end of the product’s life cycle, do
not dispose of this product in normal household waste, but take it to a
collection point for the recycling of electrical and electronic equipment.
Manual
CO2 monitor
AQ30
Packaging content Product
AQ30 monitor Micro USB cable Adapter
Manual Plugs and
screws
Bracket
Wall mount
sticker
Front
Side
Air quality
indicator Display information
Options / Power
+ / menu scroll
- / menu scroll
Mute / back
Air intake
Micro USB input
Bracket
Specications
1. Power supply: AC adapter input: 100 ~ 240V
Output DC 5V/1A Micro-USB
2. Backup battery: Lithium battery
3. Backup battery duration: Up to 6 hours
4. CO2sensor type: Non-dispersive infrared sensor
5. CO2sensor lifeteime: 10 years maximum
6. Temperature range: -10°C to 40°C
7. Humidity range: 10 to 95%
8. CO2Range: 400 - 5000ppm
9. Pre-programmed CO2
concentration levels: Good: 0 - 600ppm
Average: 600 - 1200ppm
Bad: >1200ppm (Ventilate urgently)
10.CO2concentration alarm: Bad >1200ppm (Adjustable limit)
11. Measurements: 90 x 90 x 26mm
Tips
Carefully read the below instructions and warnings before use
1. Do not place the AQ30 in direct sunlight
2. During initial use, place the AQ30 in a well-ventilated room. This allows
the AQ30 to calibrate itself. Calibration can take up to 4 days.
3. Use only the supplied power adapter.
4. Charge the battery a full 24 hours before rst use.
5. Do not cover the device or air intake while the product is in use.
6. Do not submerge the device in water or other liquids.
7. Do not place any foreign objects in the air intake of the AQ30.
8. The internal Lithium battery is a backup battery only. It works for 6
hours. It may only be replaced or removed by a specialist .Always use
the included AC power cable and adapter to power the AQ30.
9. Do not use the AQ30 after the device has been dropped, punctured or
in any other way damaged. Do not use the AQ30 if the power cable or
power adaper have been damaged.
10.The AQ30 does not contain parts that can be changed / replaced by
the user.
Wall installation
1. If you mount the monitor on the wall, preferably at breahting height,
not in a ridge, corner of a room or on a ceiling. Place it 60 cm from
surrounding walls and ceilings.
2. Use the wall mount sticker to position the
drilling holes in the desired location.
3. Drill 2 holes with a Φ5mm drill bit.
4. Push the included pluggs in the holes.
5. Screw the included screws in the plugs until they stick out about 5mm.
6. Place the AQ30 in place by positioning the screws in slots on the
backside and gently pushing the AQ30 downwards to the xed position.
Standing installation
1. Place the bracket tips in the slots on the backside of the AQ30. Make
sure the bracket foot points down.
2. Press the bracket upwards with even force until the bracket pins click
into position.
Buttons & Functions
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, reduces the current value.
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, increases the current value.
1. Deactivate the alarm sound.
2. In setup mode, go back to previous menu, exit setup mode.
1. Turn the device on or off (press & hold 5 sec ).
2. Turn off the display (short press).
3. together with for 2 seconds to enter setup mode.
4. In setup mode, short press to save the settings.
Display icons
Carbon dioxide (CO2)
CO2Parts per million
Air temperature
Degrees Fahrenheit
Degrees Celsius
Relative humidity
Percent
Time and date
Mute
Battery power (green: >50%,
Display information
CO2& Time Temperature &
Humidity
Time & Date
Setup menu’s
1. Through the various setup menu’s the date, time, minimum and
maximum values can be set. Crossing the maximum CO2 value
will trigger the visual and an alarm will sound for 30 sec. When the
maximum value is exceeded the alarm will go off.
2. Press and hold both and buttons for 2 seconds. As soon as the
icon appears the device is in setup mode.
3. Switch through the different setup menus using and . Press
to modify the menu values.
CO2display setup
Temperature screen setup
1. Set MAX/MIN temperature value: if MAX is
ashing, press and to set the MAX
value. If MIN is ashing, press and to
set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Humidity screen setup
1. Set MAX/MIN humidity value: if MAX is ashing,
press and to set the MAX value. If MIN is
ashing, press and to set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Setting the time and date
1. Press to toggle between hour, minute, day
and month.
2. Use the and buttons to set the value.
3. Press 2x to conrm the date and time and
exit the setup mode.
Issue list
Fault Troubleshooting
No display
Check that the power supply is plugged
correctly in the socket and the AQ30
Charge the battery for 24 hours.
Slow response
Make sure the air intake is not blocked
and clean.
The AQ30 displays “Err. Contact the dealer
V1.2
Do not disturb mode (Silent alarm)
1. Press the key to toggle between the start
time and end time of the don’t disturb mode
2. Press and to set the time.
3.Press 2x to conrm the time and exit the
setup mode.
4.In case of an alarm, only a visual alarm wil be
given. There will be no sound.
AQ30 introduction
The stable indoor air quality monitor (AQ30) is used for measuring the
indoor air quality. Including CO2, temperature and humidity. The advanced
AQ30 sensor measures and detecs with high stability and accuracy. When
the preprogrammed (and programmable) maximum values are surpassed
the AQ30 will sound an alarm both audibel and visually. In which case it
is important to immediately ventilate and air the room. The AQ30 is only
applicable in indoor environments like residents, ofces, schools, meeting
rooms and other public places.
1. Set MAX/MIN CO2 value: if MAX is ashing,
press and to set the MAX value. If MIN
is ashing, press and to set the MIN
value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
Setup
maximum value
minimum value
End time
Air quality indicator
yellow: 25-50%, red: <25%)
green: air quality good
yellow: air quality moderate
red: air quality bad
400 5000
Min Max
vv

ENVIRONMENT:
Do not dispose of spent batteries but return them to your local depot for
Small Chemical Waste (MSW). At the end of the product’s life cycle, do
not dispose of this product in normal household waste, but take it to a
collection point for the recycling of electrical and electronic equipment.
Manual
CO2 monitor
AQ30
Packaging content Product
AQ30 monitor Micro USB cable Adapter
Manual Plugs and
screws
Bracket
Wall mount
sticker
Front
Side
Air quality
indicator Display information
Options / Power
+ / menu scroll
- / menu scroll
Mute / back
Air intake
Micro USB input
Bracket
Specications
1. Power supply: AC adapter input: 100 ~ 240V
Output DC 5V/1A Micro-USB
2. Backup battery: Lithium battery
3. Backup battery duration: Up to 6 hours
4. CO2sensor type: Non-dispersive infrared sensor
5. CO2sensor lifeteime: 10 years maximum
6. Temperature range: -10°C to 40°C
7. Humidity range: 10 to 95%
8. CO2Range: 400 - 5000ppm
9. Pre-programmed CO2
concentration levels: Good: 0 - 600ppm
Average: 600 - 1200ppm
Bad: >1200ppm (Ventilate urgently)
10.CO2concentration alarm: Bad >1200ppm (Adjustable limit)
11. Measurements: 90 x 90 x 26mm
Tips
Carefully read the below instructions and warnings before use
1. Do not place the AQ30 in direct sunlight
2. During initial use, place the AQ30 in a well-ventilated room. This allows
the AQ30 to calibrate itself. Calibration can take up to 4 days.
3. Use only the supplied power adapter.
4. Charge the battery a full 24 hours before rst use.
5. Do not cover the device or air intake while the product is in use.
6. Do not submerge the device in water or other liquids.
7. Do not place any foreign objects in the air intake of the AQ30.
8. The internal Lithium battery is a backup battery only. It works for 6
hours. It may only be replaced or removed by a specialist .Always use
the included AC power cable and adapter to power the AQ30.
9. Do not use the AQ30 after the device has been dropped, punctured or
in any other way damaged. Do not use the AQ30 if the power cable or
power adaper have been damaged.
10.The AQ30 does not contain parts that can be changed / replaced by
the user.
Wall installation
1. If you mount the monitor on the wall, preferably at breahting height,
not in a ridge, corner of a room or on a ceiling. Place it 60 cm from
surrounding walls and ceilings.
2. Use the wall mount sticker to position the
drilling holes in the desired location.
3. Drill 2 holes with a Φ5mm drill bit.
4. Push the included pluggs in the holes.
5. Screw the included screws in the plugs until they stick out about 5mm.
6. Place the AQ30 in place by positioning the screws in slots on the
backside and gently pushing the AQ30 downwards to the xed position.
Standing installation
1. Place the bracket tips in the slots on the backside of the AQ30. Make
sure the bracket foot points down.
2. Press the bracket upwards with even force until the bracket pins click
into position.
Buttons & Functions
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, reduces the current value.
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, increases the current value.
1. Deactivate the alarm sound.
2. In setup mode, go back to previous menu, exit setup mode.
1. Turn the device on or off (press & hold 5 sec ).
2. Turn off the display (short press).
3. together with for 2 seconds to enter setup mode.
4. In setup mode, short press to save the settings.
Display icons
Carbon dioxide (CO2)
CO2Parts per million
Air temperature
Degrees Fahrenheit
Degrees Celsius
Relative humidity
Percent
Time and date
Mute
Battery power (green: >50%,
Display information
CO2& Time Temperature &
Humidity
Time & Date
Setup menu’s
1. Through the various setup menu’s the date, time, minimum and
maximum values can be set. Crossing the maximum CO2 value
will trigger the visual and an alarm will sound for 30 sec. When the
maximum value is exceeded the alarm will go off.
2. Press and hold both and buttons for 2 seconds. As soon as the
icon appears the device is in setup mode.
3. Switch through the different setup menus using and . Press
to modify the menu values.
CO2display setup
Temperature screen setup
1. Set MAX/MIN temperature value: if MAX is
ashing, press and to set the MAX
value. If MIN is ashing, press and to
set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Humidity screen setup
1. Set MAX/MIN humidity value: if MAX is ashing,
press and to set the MAX value. If MIN is
ashing, press and to set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Setting the time and date
1. Press to toggle between hour, minute, day
and month.
2. Use the and buttons to set the value.
3. Press 2x to conrm the date and time and
exit the setup mode.
Issue list
Fault Troubleshooting
No display
Check that the power supply is plugged
correctly in the socket and the AQ30
Charge the battery for 24 hours.
Slow response
Make sure the air intake is not blocked
and clean.
The AQ30 displays “Err. Contact the dealer
V1.2
Do not disturb mode (Silent alarm)
1. Press the key to toggle between the start
time and end time of the don’t disturb mode
2. Press and to set the time.
3.Press 2x to conrm the time and exit the
setup mode.
4.In case of an alarm, only a visual alarm wil be
given. There will be no sound.
AQ30 introduction
The stable indoor air quality monitor (AQ30) is used for measuring the
indoor air quality. Including CO2, temperature and humidity. The advanced
AQ30 sensor measures and detecs with high stability and accuracy. When
the preprogrammed (and programmable) maximum values are surpassed
the AQ30 will sound an alarm both audibel and visually. In which case it
is important to immediately ventilate and air the room. The AQ30 is only
applicable in indoor environments like residents, ofces, schools, meeting
rooms and other public places.
1. Set MAX/MIN CO2 value: if MAX is ashing,
press and to set the MAX value. If MIN
is ashing, press and to set the MIN
value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
Setup
maximum value
minimum value
End time
Air quality indicator
yellow: 25-50%, red: <25%)
green: air quality good
yellow: air quality moderate
red: air quality bad
400 5000
Min Max
vv

ENVIRONMENT:
Do not dispose of spent batteries but return them to your local depot for
Small Chemical Waste (MSW). At the end of the product’s life cycle, do
not dispose of this product in normal household waste, but take it to a
collection point for the recycling of electrical and electronic equipment.
Manual
CO2 monitor
AQ30
Packaging content Product
AQ30 monitor Micro USB cable Adapter
Manual Plugs and
screws
Bracket
Wall mount
sticker
Front
Side
Air quality
indicator Display information
Options / Power
+ / menu scroll
- / menu scroll
Mute / back
Air intake
Micro USB input
Bracket
Specications
1. Power supply: AC adapter input: 100 ~ 240V
Output DC 5V/1A Micro-USB
2. Backup battery: Lithium battery
3. Backup battery duration: Up to 6 hours
4. CO2sensor type: Non-dispersive infrared sensor
5. CO2sensor lifeteime: 10 years maximum
6. Temperature range: -10°C to 40°C
7. Humidity range: 10 to 95%
8. CO2Range: 400 - 5000ppm
9. Pre-programmed CO2
concentration levels: Good: 0 - 600ppm
Average: 600 - 1200ppm
Bad: >1200ppm (Ventilate urgently)
10.CO2concentration alarm: Bad >1200ppm (Adjustable limit)
11. Measurements: 90 x 90 x 26mm
Tips
Carefully read the below instructions and warnings before use
1. Do not place the AQ30 in direct sunlight
2. During initial use, place the AQ30 in a well-ventilated room. This allows
the AQ30 to calibrate itself. Calibration can take up to 4 days.
3. Use only the supplied power adapter.
4. Charge the battery a full 24 hours before rst use.
5. Do not cover the device or air intake while the product is in use.
6. Do not submerge the device in water or other liquids.
7. Do not place any foreign objects in the air intake of the AQ30.
8. The internal Lithium battery is a backup battery only. It works for 6
hours. It may only be replaced or removed by a specialist .Always use
the included AC power cable and adapter to power the AQ30.
9. Do not use the AQ30 after the device has been dropped, punctured or
in any other way damaged. Do not use the AQ30 if the power cable or
power adaper have been damaged.
10.The AQ30 does not contain parts that can be changed / replaced by
the user.
Wall installation
1. If you mount the monitor on the wall, preferably at breahting height,
not in a ridge, corner of a room or on a ceiling. Place it 60 cm from
surrounding walls and ceilings.
2. Use the wall mount sticker to position the
drilling holes in the desired location.
3. Drill 2 holes with a Φ5mm drill bit.
4. Push the included pluggs in the holes.
5. Screw the included screws in the plugs until they stick out about 5mm.
6. Place the AQ30 in place by positioning the screws in slots on the
backside and gently pushing the AQ30 downwards to the xed position.
Standing installation
1. Place the bracket tips in the slots on the backside of the AQ30. Make
sure the bracket foot points down.
2. Press the bracket upwards with even force until the bracket pins click
into position.
Buttons & Functions
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, reduces the current value.
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, increases the current value.
1. Deactivate the alarm sound.
2. In setup mode, go back to previous menu, exit setup mode.
1. Turn the device on or off (press & hold 5 sec ).
2. Turn off the display (short press).
3. together with for 2 seconds to enter setup mode.
4. In setup mode, short press to save the settings.
Display icons
Carbon dioxide (CO2)
CO2Parts per million
Air temperature
Degrees Fahrenheit
Degrees Celsius
Relative humidity
Percent
Time and date
Mute
Battery power (green: >50%,
Display information
CO2& Time Temperature &
Humidity
Time & Date
Setup menu’s
1. Through the various setup menu’s the date, time, minimum and
maximum values can be set. Crossing the maximum CO2 value
will trigger the visual and an alarm will sound for 30 sec. When the
maximum value is exceeded the alarm will go off.
2. Press and hold both and buttons for 2 seconds. As soon as the
icon appears the device is in setup mode.
3. Switch through the different setup menus using and . Press
to modify the menu values.
CO2display setup
Temperature screen setup
1. Set MAX/MIN temperature value: if MAX is
ashing, press and to set the MAX
value. If MIN is ashing, press and to
set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Humidity screen setup
1. Set MAX/MIN humidity value: if MAX is ashing,
press and to set the MAX value. If MIN is
ashing, press and to set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Setting the time and date
1. Press to toggle between hour, minute, day
and month.
2. Use the and buttons to set the value.
3. Press 2x to conrm the date and time and
exit the setup mode.
Issue list
Fault Troubleshooting
No display
Check that the power supply is plugged
correctly in the socket and the AQ30
Charge the battery for 24 hours.
Slow response
Make sure the air intake is not blocked
and clean.
The AQ30 displays “Err. Contact the dealer
V1.2
Do not disturb mode (Silent alarm)
1. Press the key to toggle between the start
time and end time of the don’t disturb mode
2. Press and to set the time.
3.Press 2x to conrm the time and exit the
setup mode.
4.In case of an alarm, only a visual alarm wil be
given. There will be no sound.
AQ30 introduction
The stable indoor air quality monitor (AQ30) is used for measuring the
indoor air quality. Including CO2, temperature and humidity. The advanced
AQ30 sensor measures and detecs with high stability and accuracy. When
the preprogrammed (and programmable) maximum values are surpassed
the AQ30 will sound an alarm both audibel and visually. In which case it
is important to immediately ventilate and air the room. The AQ30 is only
applicable in indoor environments like residents, ofces, schools, meeting
rooms and other public places.
1. Set MAX/MIN CO2 value: if MAX is ashing,
press and to set the MAX value. If MIN
is ashing, press and to set the MIN
value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
Setup
maximum value
minimum value
End time
Air quality indicator
yellow: 25-50%, red: <25%)
green: air quality good
yellow: air quality moderate
red: air quality bad
400 5000
Min Max
vv

ENVIRONMENT:
Do not dispose of spent batteries but return them to your local depot for
Small Chemical Waste (MSW). At the end of the product’s life cycle, do
not dispose of this product in normal household waste, but take it to a
collection point for the recycling of electrical and electronic equipment.
Manual
CO2 monitor
AQ30
Packaging content Product
AQ30 monitor Micro USB cable Adapter
Manual Plugs and
screws
Bracket
Wall mount
sticker
Front
Side
Air quality
indicator Display information
Options / Power
+ / menu scroll
- / menu scroll
Mute / back
Air intake
Micro USB input
Bracket
Specications
1. Power supply: AC adapter input: 100 ~ 240V
Output DC 5V/1A Micro-USB
2. Backup battery: Lithium battery
3. Backup battery duration: Up to 6 hours
4. CO2sensor type: Non-dispersive infrared sensor
5. CO2sensor lifeteime: 10 years maximum
6. Temperature range: -10°C to 40°C
7. Humidity range: 10 to 95%
8. CO2Range: 400 - 5000ppm
9. Pre-programmed CO2
concentration levels: Good: 0 - 600ppm
Average: 600 - 1200ppm
Bad: >1200ppm (Ventilate urgently)
10.CO2concentration alarm: Bad >1200ppm (Adjustable limit)
11. Measurements: 90 x 90 x 26mm
Tips
Carefully read the below instructions and warnings before use
1. Do not place the AQ30 in direct sunlight
2. During initial use, place the AQ30 in a well-ventilated room. This allows
the AQ30 to calibrate itself. Calibration can take up to 4 days.
3. Use only the supplied power adapter.
4. Charge the battery a full 24 hours before rst use.
5. Do not cover the device or air intake while the product is in use.
6. Do not submerge the device in water or other liquids.
7. Do not place any foreign objects in the air intake of the AQ30.
8. The internal Lithium battery is a backup battery only. It works for 6
hours. It may only be replaced or removed by a specialist .Always use
the included AC power cable and adapter to power the AQ30.
9. Do not use the AQ30 after the device has been dropped, punctured or
in any other way damaged. Do not use the AQ30 if the power cable or
power adaper have been damaged.
10.The AQ30 does not contain parts that can be changed / replaced by
the user.
Wall installation
1. If you mount the monitor on the wall, preferably at breahting height,
not in a ridge, corner of a room or on a ceiling. Place it 60 cm from
surrounding walls and ceilings.
2. Use the wall mount sticker to position the
drilling holes in the desired location.
3. Drill 2 holes with a Φ5mm drill bit.
4. Push the included pluggs in the holes.
5. Screw the included screws in the plugs until they stick out about 5mm.
6. Place the AQ30 in place by positioning the screws in slots on the
backside and gently pushing the AQ30 downwards to the xed position.
Standing installation
1. Place the bracket tips in the slots on the backside of the AQ30. Make
sure the bracket foot points down.
2. Press the bracket upwards with even force until the bracket pins click
into position.
Buttons & Functions
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, reduces the current value.
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, increases the current value.
1. Deactivate the alarm sound.
2. In setup mode, go back to previous menu, exit setup mode.
1. Turn the device on or off (press & hold 5 sec ).
2. Turn off the display (short press).
3. together with for 2 seconds to enter setup mode.
4. In setup mode, short press to save the settings.
Display icons
Carbon dioxide (CO2)
CO2Parts per million
Air temperature
Degrees Fahrenheit
Degrees Celsius
Relative humidity
Percent
Time and date
Mute
Battery power (green: >50%,
Display information
CO2& Time Temperature &
Humidity
Time & Date
Setup menu’s
1. Through the various setup menu’s the date, time, minimum and
maximum values can be set. Crossing the maximum CO2 value
will trigger the visual and an alarm will sound for 30 sec. When the
maximum value is exceeded the alarm will go off.
2. Press and hold both and buttons for 2 seconds. As soon as the
icon appears the device is in setup mode.
3. Switch through the different setup menus using and . Press
to modify the menu values.
CO2display setup
Temperature screen setup
1. Set MAX/MIN temperature value: if MAX is
ashing, press and to set the MAX
value. If MIN is ashing, press and to
set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Humidity screen setup
1. Set MAX/MIN humidity value: if MAX is ashing,
press and to set the MAX value. If MIN is
ashing, press and to set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Setting the time and date
1. Press to toggle between hour, minute, day
and month.
2. Use the and buttons to set the value.
3. Press 2x to conrm the date and time and
exit the setup mode.
Issue list
Fault Troubleshooting
No display
Check that the power supply is plugged
correctly in the socket and the AQ30
Charge the battery for 24 hours.
Slow response
Make sure the air intake is not blocked
and clean.
The AQ30 displays “Err. Contact the dealer
V1.2
Do not disturb mode (Silent alarm)
1. Press the key to toggle between the start
time and end time of the don’t disturb mode
2. Press and to set the time.
3.Press 2x to conrm the time and exit the
setup mode.
4.In case of an alarm, only a visual alarm wil be
given. There will be no sound.
AQ30 introduction
The stable indoor air quality monitor (AQ30) is used for measuring the
indoor air quality. Including CO2, temperature and humidity. The advanced
AQ30 sensor measures and detecs with high stability and accuracy. When
the preprogrammed (and programmable) maximum values are surpassed
the AQ30 will sound an alarm both audibel and visually. In which case it
is important to immediately ventilate and air the room. The AQ30 is only
applicable in indoor environments like residents, ofces, schools, meeting
rooms and other public places.
1. Set MAX/MIN CO2 value: if MAX is ashing,
press and to set the MAX value. If MIN
is ashing, press and to set the MIN
value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
Setup
maximum value
minimum value
End time
Air quality indicator
yellow: 25-50%, red: <25%)
green: air quality good
yellow: air quality moderate
red: air quality bad
400 5000
Min Max
vv

ENVIRONMENT:
Do not dispose of spent batteries but return them to your local depot for
Small Chemical Waste (MSW). At the end of the product’s life cycle, do
not dispose of this product in normal household waste, but take it to a
collection point for the recycling of electrical and electronic equipment.
Manual
CO2 monitor
AQ30
Packaging content Product
AQ30 monitor Micro USB cable Adapter
Manual Plugs and
screws
Bracket
Wall mount
sticker
Front
Side
Air quality
indicator Display information
Options / Power
+ / menu scroll
- / menu scroll
Mute / back
Air intake
Micro USB input
Bracket
Specications
1. Power supply: AC adapter input: 100 ~ 240V
Output DC 5V/1A Micro-USB
2. Backup battery: Lithium battery
3. Backup battery duration: Up to 6 hours
4. CO2sensor type: Non-dispersive infrared sensor
5. CO2sensor lifeteime: 10 years maximum
6. Temperature range: -10°C to 40°C
7. Humidity range: 10 to 95%
8. CO2Range: 400 - 5000ppm
9. Pre-programmed CO2
concentration levels: Good: 0 - 600ppm
Average: 600 - 1200ppm
Bad: >1200ppm (Ventilate urgently)
10.CO2concentration alarm: Bad >1200ppm (Adjustable limit)
11. Measurements: 90 x 90 x 26mm
Tips
Carefully read the below instructions and warnings before use
1. Do not place the AQ30 in direct sunlight
2. During initial use, place the AQ30 in a well-ventilated room. This allows
the AQ30 to calibrate itself. Calibration can take up to 4 days.
3. Use only the supplied power adapter.
4. Charge the battery a full 24 hours before rst use.
5. Do not cover the device or air intake while the product is in use.
6. Do not submerge the device in water or other liquids.
7. Do not place any foreign objects in the air intake of the AQ30.
8. The internal Lithium battery is a backup battery only. It works for 6
hours. It may only be replaced or removed by a specialist .Always use
the included AC power cable and adapter to power the AQ30.
9. Do not use the AQ30 after the device has been dropped, punctured or
in any other way damaged. Do not use the AQ30 if the power cable or
power adaper have been damaged.
10.The AQ30 does not contain parts that can be changed / replaced by
the user.
Wall installation
1. If you mount the monitor on the wall, preferably at breahting height,
not in a ridge, corner of a room or on a ceiling. Place it 60 cm from
surrounding walls and ceilings.
2. Use the wall mount sticker to position the
drilling holes in the desired location.
3. Drill 2 holes with a Φ5mm drill bit.
4. Push the included pluggs in the holes.
5. Screw the included screws in the plugs until they stick out about 5mm.
6. Place the AQ30 in place by positioning the screws in slots on the
backside and gently pushing the AQ30 downwards to the xed position.
Standing installation
1. Place the bracket tips in the slots on the backside of the AQ30. Make
sure the bracket foot points down.
2. Press the bracket upwards with even force until the bracket pins click
into position.
Buttons & Functions
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, reduces the current value.
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, increases the current value.
1. Deactivate the alarm sound.
2. In setup mode, go back to previous menu, exit setup mode.
1. Turn the device on or off (press & hold 5 sec ).
2. Turn off the display (short press).
3. together with for 2 seconds to enter setup mode.
4. In setup mode, short press to save the settings.
Display icons
Carbon dioxide (CO2)
CO2Parts per million
Air temperature
Degrees Fahrenheit
Degrees Celsius
Relative humidity
Percent
Time and date
Mute
Battery power (green: >50%,
Display information
CO2& Time Temperature &
Humidity
Time & Date
Setup menu’s
1. Through the various setup menu’s the date, time, minimum and
maximum values can be set. Crossing the maximum CO2 value
will trigger the visual and an alarm will sound for 30 sec. When the
maximum value is exceeded the alarm will go off.
2. Press and hold both and buttons for 2 seconds. As soon as the
icon appears the device is in setup mode.
3. Switch through the different setup menus using and . Press
to modify the menu values.
CO2display setup
Temperature screen setup
1. Set MAX/MIN temperature value: if MAX is
ashing, press and to set the MAX
value. If MIN is ashing, press and to
set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Humidity screen setup
1. Set MAX/MIN humidity value: if MAX is ashing,
press and to set the MAX value. If MIN is
ashing, press and to set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Setting the time and date
1. Press to toggle between hour, minute, day
and month.
2. Use the and buttons to set the value.
3. Press 2x to conrm the date and time and
exit the setup mode.
Issue list
Fault Troubleshooting
No display
Check that the power supply is plugged
correctly in the socket and the AQ30
Charge the battery for 24 hours.
Slow response
Make sure the air intake is not blocked
and clean.
The AQ30 displays “Err. Contact the dealer
V1.2
Do not disturb mode (Silent alarm)
1. Press the key to toggle between the start
time and end time of the don’t disturb mode
2. Press and to set the time.
3.Press 2x to conrm the time and exit the
setup mode.
4.In case of an alarm, only a visual alarm wil be
given. There will be no sound.
AQ30 introduction
The stable indoor air quality monitor (AQ30) is used for measuring the
indoor air quality. Including CO2, temperature and humidity. The advanced
AQ30 sensor measures and detecs with high stability and accuracy. When
the preprogrammed (and programmable) maximum values are surpassed
the AQ30 will sound an alarm both audibel and visually. In which case it
is important to immediately ventilate and air the room. The AQ30 is only
applicable in indoor environments like residents, ofces, schools, meeting
rooms and other public places.
1. Set MAX/MIN CO2 value: if MAX is ashing,
press and to set the MAX value. If MIN
is ashing, press and to set the MIN
value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
Setup
maximum value
minimum value
End time
Air quality indicator
yellow: 25-50%, red: <25%)
green: air quality good
yellow: air quality moderate
red: air quality bad
400 5000
Min Max
vv

ENVIRONMENT:
Do not dispose of spent batteries but return them to your local depot for
Small Chemical Waste (MSW). At the end of the product’s life cycle, do
not dispose of this product in normal household waste, but take it to a
collection point for the recycling of electrical and electronic equipment.
Manual
CO2 monitor
AQ30
Packaging content Product
AQ30 monitor Micro USB cable Adapter
Manual Plugs and
screws
Bracket
Wall mount
sticker
Front
Side
Air quality
indicator Display information
Options / Power
+ / menu scroll
- / menu scroll
Mute / back
Air intake
Micro USB input
Bracket
Specications
1. Power supply: AC adapter input: 100 ~ 240V
Output DC 5V/1A Micro-USB
2. Backup battery: Lithium battery
3. Backup battery duration: Up to 6 hours
4. CO2sensor type: Non-dispersive infrared sensor
5. CO2sensor lifeteime: 10 years maximum
6. Temperature range: -10°C to 40°C
7. Humidity range: 10 to 95%
8. CO2Range: 400 - 5000ppm
9. Pre-programmed CO2
concentration levels: Good: 0 - 600ppm
Average: 600 - 1200ppm
Bad: >1200ppm (Ventilate urgently)
10.CO2concentration alarm: Bad >1200ppm (Adjustable limit)
11. Measurements: 90 x 90 x 26mm
Tips
Carefully read the below instructions and warnings before use
1. Do not place the AQ30 in direct sunlight
2. During initial use, place the AQ30 in a well-ventilated room. This allows
the AQ30 to calibrate itself. Calibration can take up to 4 days.
3. Use only the supplied power adapter.
4. Charge the battery a full 24 hours before rst use.
5. Do not cover the device or air intake while the product is in use.
6. Do not submerge the device in water or other liquids.
7. Do not place any foreign objects in the air intake of the AQ30.
8. The internal Lithium battery is a backup battery only. It works for 6
hours. It may only be replaced or removed by a specialist .Always use
the included AC power cable and adapter to power the AQ30.
9. Do not use the AQ30 after the device has been dropped, punctured or
in any other way damaged. Do not use the AQ30 if the power cable or
power adaper have been damaged.
10.The AQ30 does not contain parts that can be changed / replaced by
the user.
Wall installation
1. If you mount the monitor on the wall, preferably at breahting height,
not in a ridge, corner of a room or on a ceiling. Place it 60 cm from
surrounding walls and ceilings.
2. Use the wall mount sticker to position the
drilling holes in the desired location.
3. Drill 2 holes with a Φ5mm drill bit.
4. Push the included pluggs in the holes.
5. Screw the included screws in the plugs until they stick out about 5mm.
6. Place the AQ30 in place by positioning the screws in slots on the
backside and gently pushing the AQ30 downwards to the xed position.
Standing installation
1. Place the bracket tips in the slots on the backside of the AQ30. Make
sure the bracket foot points down.
2. Press the bracket upwards with even force until the bracket pins click
into position.
Buttons & Functions
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, reduces the current value.
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, increases the current value.
1. Deactivate the alarm sound.
2. In setup mode, go back to previous menu, exit setup mode.
1. Turn the device on or off (press & hold 5 sec ).
2. Turn off the display (short press).
3. together with for 2 seconds to enter setup mode.
4. In setup mode, short press to save the settings.
Display icons
Carbon dioxide (CO2)
CO2Parts per million
Air temperature
Degrees Fahrenheit
Degrees Celsius
Relative humidity
Percent
Time and date
Mute
Battery power (green: >50%,
Display information
CO2& Time Temperature &
Humidity
Time & Date
Setup menu’s
1. Through the various setup menu’s the date, time, minimum and
maximum values can be set. Crossing the maximum CO2 value
will trigger the visual and an alarm will sound for 30 sec. When the
maximum value is exceeded the alarm will go off.
2. Press and hold both and buttons for 2 seconds. As soon as the
icon appears the device is in setup mode.
3. Switch through the different setup menus using and . Press
to modify the menu values.
CO2display setup
Temperature screen setup
1. Set MAX/MIN temperature value: if MAX is
ashing, press and to set the MAX
value. If MIN is ashing, press and to
set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Humidity screen setup
1. Set MAX/MIN humidity value: if MAX is ashing,
press and to set the MAX value. If MIN is
ashing, press and to set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Setting the time and date
1. Press to toggle between hour, minute, day
and month.
2. Use the and buttons to set the value.
3. Press 2x to conrm the date and time and
exit the setup mode.
Issue list
Fault Troubleshooting
No display
Check that the power supply is plugged
correctly in the socket and the AQ30
Charge the battery for 24 hours.
Slow response
Make sure the air intake is not blocked
and clean.
The AQ30 displays “Err. Contact the dealer
V1.2
Do not disturb mode (Silent alarm)
1. Press the key to toggle between the start
time and end time of the don’t disturb mode
2. Press and to set the time.
3.Press 2x to conrm the time and exit the
setup mode.
4.In case of an alarm, only a visual alarm wil be
given. There will be no sound.
AQ30 introduction
The stable indoor air quality monitor (AQ30) is used for measuring the
indoor air quality. Including CO2, temperature and humidity. The advanced
AQ30 sensor measures and detecs with high stability and accuracy. When
the preprogrammed (and programmable) maximum values are surpassed
the AQ30 will sound an alarm both audibel and visually. In which case it
is important to immediately ventilate and air the room. The AQ30 is only
applicable in indoor environments like residents, ofces, schools, meeting
rooms and other public places.
1. Set MAX/MIN CO2 value: if MAX is ashing,
press and to set the MAX value. If MIN
is ashing, press and to set the MIN
value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
Setup
maximum value
minimum value
End time
Air quality indicator
yellow: 25-50%, red: <25%)
green: air quality good
yellow: air quality moderate
red: air quality bad
400 5000
Min Max
vv

ENVIRONMENT:
Do not dispose of spent batteries but return them to your local depot for
Small Chemical Waste (MSW). At the end of the product’s life cycle, do
not dispose of this product in normal household waste, but take it to a
collection point for the recycling of electrical and electronic equipment.
Manual
CO2 monitor
AQ30
Packaging content Product
AQ30 monitor Micro USB cable Adapter
Manual Plugs and
screws
Bracket
Wall mount
sticker
Front
Side
Air quality
indicator Display information
Options / Power
+ / menu scroll
- / menu scroll
Mute / back
Air intake
Micro USB input
Bracket
Specications
1. Power supply: AC adapter input: 100 ~ 240V
Output DC 5V/1A Micro-USB
2. Backup battery: Lithium battery
3. Backup battery duration: Up to 6 hours
4. CO2sensor type: Non-dispersive infrared sensor
5. CO2sensor lifeteime: 10 years maximum
6. Temperature range: -10°C to 40°C
7. Humidity range: 10 to 95%
8. CO2Range: 400 - 5000ppm
9. Pre-programmed CO2
concentration levels: Good: 0 - 600ppm
Average: 600 - 1200ppm
Bad: >1200ppm (Ventilate urgently)
10.CO2concentration alarm: Bad >1200ppm (Adjustable limit)
11. Measurements: 90 x 90 x 26mm
Tips
Carefully read the below instructions and warnings before use
1. Do not place the AQ30 in direct sunlight
2. During initial use, place the AQ30 in a well-ventilated room. This allows
the AQ30 to calibrate itself. Calibration can take up to 4 days.
3. Use only the supplied power adapter.
4. Charge the battery a full 24 hours before rst use.
5. Do not cover the device or air intake while the product is in use.
6. Do not submerge the device in water or other liquids.
7. Do not place any foreign objects in the air intake of the AQ30.
8. The internal Lithium battery is a backup battery only. It works for 6
hours. It may only be replaced or removed by a specialist .Always use
the included AC power cable and adapter to power the AQ30.
9. Do not use the AQ30 after the device has been dropped, punctured or
in any other way damaged. Do not use the AQ30 if the power cable or
power adaper have been damaged.
10.The AQ30 does not contain parts that can be changed / replaced by
the user.
Wall installation
1. If you mount the monitor on the wall, preferably at breahting height,
not in a ridge, corner of a room or on a ceiling. Place it 60 cm from
surrounding walls and ceilings.
2. Use the wall mount sticker to position the
drilling holes in the desired location.
3. Drill 2 holes with a Φ5mm drill bit.
4. Push the included pluggs in the holes.
5. Screw the included screws in the plugs until they stick out about 5mm.
6. Place the AQ30 in place by positioning the screws in slots on the
backside and gently pushing the AQ30 downwards to the xed position.
Standing installation
1. Place the bracket tips in the slots on the backside of the AQ30. Make
sure the bracket foot points down.
2. Press the bracket upwards with even force until the bracket pins click
into position.
Buttons & Functions
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, reduces the current value.
1. Toggle through the menus CO2, Temperature/Humidity and Time/
Date.
2. In setup mode, increases the current value.
1. Deactivate the alarm sound.
2. In setup mode, go back to previous menu, exit setup mode.
1. Turn the device on or off (press & hold 5 sec ).
2. Turn off the display (short press).
3. together with for 2 seconds to enter setup mode.
4. In setup mode, short press to save the settings.
Display icons
Carbon dioxide (CO2)
CO2Parts per million
Air temperature
Degrees Fahrenheit
Degrees Celsius
Relative humidity
Percent
Time and date
Mute
Battery power (green: >50%,
Display information
CO2& Time Temperature &
Humidity
Time & Date
Setup menu’s
1. Through the various setup menu’s the date, time, minimum and
maximum values can be set. Crossing the maximum CO2 value
will trigger the visual and an alarm will sound for 30 sec. When the
maximum value is exceeded the alarm will go off.
2. Press and hold both and buttons for 2 seconds. As soon as the
icon appears the device is in setup mode.
3. Switch through the different setup menus using and . Press
to modify the menu values.
CO2display setup
Temperature screen setup
1. Set MAX/MIN temperature value: if MAX is
ashing, press and to set the MAX
value. If MIN is ashing, press and to
set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Humidity screen setup
1. Set MAX/MIN humidity value: if MAX is ashing,
press and to set the MAX value. If MIN is
ashing, press and to set the MIN value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
4. In case of an alarm, only a visual alarm wil be
given. There will be no sound.
Setting the time and date
1. Press to toggle between hour, minute, day
and month.
2. Use the and buttons to set the value.
3. Press 2x to conrm the date and time and
exit the setup mode.
Issue list
Fault Troubleshooting
No display
Check that the power supply is plugged
correctly in the socket and the AQ30
Charge the battery for 24 hours.
Slow response
Make sure the air intake is not blocked
and clean.
The AQ30 displays “Err. Contact the dealer
V1.2
Do not disturb mode (Silent alarm)
1. Press the key to toggle between the start
time and end time of the don’t disturb mode
2. Press and to set the time.
3.Press 2x to conrm the time and exit the
setup mode.
4.In case of an alarm, only a visual alarm wil be
given. There will be no sound.
AQ30 introduction
The stable indoor air quality monitor (AQ30) is used for measuring the
indoor air quality. Including CO2, temperature and humidity. The advanced
AQ30 sensor measures and detecs with high stability and accuracy. When
the preprogrammed (and programmable) maximum values are surpassed
the AQ30 will sound an alarm both audibel and visually. In which case it
is important to immediately ventilate and air the room. The AQ30 is only
applicable in indoor environments like residents, ofces, schools, meeting
rooms and other public places.
1. Set MAX/MIN CO2 value: if MAX is ashing,
press and to set the MAX value. If MIN
is ashing, press and to set the MIN
value.
2. Press shortly to save the set values.
3. Press shortly to toggle between MAX and
MIN values. Press 2x to exit the setup mode.
Setup
maximum value
minimum value
End time
Air quality indicator
yellow: 25-50%, red: <25%)
green: air quality good
yellow: air quality moderate
red: air quality bad
400 5000
Min Max
vv