Alemlube 51008P User manual

Suitable for Measuring the transfer of petrol
Flow rate 20 L/min to 120 L/min
Maximum Pressure 3 bar (50psi)
Weight 2.0kg Accuracy-+1.0%
Inlet/Outlet connections 1” BSP (F)
Operating Instructions
1 Configure the meter in an orientation that suits your application i.e.: by
undoing screws at the base of the meter and reorientate the meter so that
the inlet and outlet of the meter suit your application.
2 Connect the meter inlet to the hose or fixed fitting that the product is being
delivered through.
3 Once threads connected and completely sealed with thread tape, open the
tanks on/off valve or start up the pump.
4 Petrol will now start to flow through to the mechanical flow meter turning
over the batch recording digits and totaliser recording digits
Important To Note:
The 51008 and 51008F fuel meters are pre-calibrated in factory to be used
with petrol fuel. As specific operating conditions (such as real flow rate,
the viscosity and temperature of the measured fluid) may affect the meter
accuracy, a recalibration should be carried out after the installation has
been completed. A new calibration is necessary each time the meter is
disassembled for maintenance operations or when it is used to measure
fluids that differ from petrol fuel.
Calibration Procedure
1 Unscrew the plug (Part No. 51008-4)
2 Purge the system (pump, pipelines, meter) of air by dispensing until the
flow of petrol is full and steady.
3 Stop the flow by shutting off the nozzle, but keep the pump running.
4 Reset the batch register by means of the reset know
(Part No. 51008-2).
5 Dispense at the flow rate which the best accuracy is required at, by using
a calibration container having a capacity not less than 20L. Do not reduce
the flow in order to reach the graduated zone of the calibration container.
The right way to do this is to start and stop the flow rate repeatedly until the
required filling is obtained.
6 Compare the indication of the calibration with the one of the meter. If the
indicated value is higher than the real value, loosen the screw
(Part No.51008-13) if the indicated value is lower than the real value,
tighten the screw (Part No. 51008-13).
Description
The 51008P mechanical petrol meter has an aluminium body incorporating an inlet and outlet flange and can meter petrol accurately
between 15 and 120 L/min. Featuring an oscillating plate, the meter incorporates bypasses which enable the meter to be used on
petrol of varying viscosity’s. The meter features rotational inlet/outlet for vertical or horizontal applications. The meter includes a set
of resetable digits that need to be reset to zero before the meter is to be used to record its next batch reading. The meter can be
supplied with a 1”BSP (f) filter, an optional extra (Part No. 51008F) or without the filter (Part No. 51008P.)
Specifications
7 Repeat the operations 4 to 6 until accuracy is satisfactory.
8 Tighten the plug (Part No. 51008-14) again. The O’Ring (Part No. 51008-11) which the calibration screw is
provided with has the function to avoid accidental loosening of the adjustment screw but does not facilitate
any sealing function.
Visit our website at www.alemlube.com.au Email - [email protected]
NSW
TEL: [phone]
FAX: [phone]
QLD/PNG
TEL: [phone]
FAX: [phone]
VIC/TAS
TEL: [phone]
FAX: [phone]
WA
TEL: [phone]
FAX: [phone]
SA/NT
TEL: [phone]
FAX: [phone]
NZ
TEL: [phone]
FAX: [phone]
Mechanical Petrol Meter 51008P
OWNER’S TECHNICAL MANUAL

ITEM NO PART NO DESCRIPTION ITEM NO PART NO DESCRIPTION
gniRO11-8001511etalpemaN1-800151
gniRO21-8001521bonkteseR2-800152
tsujdassapyB31-8001531revoclanretxE3-800153 ing screw
gulpssapyB41-8001541gulP4-800154
rebmahcgnirusaeM51-8001551wercS5-800155
gniRO61-8001561ylbmessareteM6-800156
gnirpSrednilyC71-8001571wercS7-800157
wercS81-8001581revocydoB8-800158
reveLgnivirD91-8001591ydobre
teM9-800159
etalPraeG02-8001502gniRO01-8001501
21 51008-21 Bevel Pinion shaft
22 51008-22 Cover Sealing Kit
23 51008-23 Bevel Pinion
PROBLEM REMEDY
Leak from the shaft gasket due to damaged gasket. Remove the gear assembly and replace the O Ring (Part No. 51008-22) and the bush.
Insufficient accuracy due to wrong calibration. Repeat calibration following the instructions on Page 1.
Insufficient accuracy due to soiled or blocked measuring chamber. Clean the measuring chamber with an appropriate cleaning agent.
acoL.diulfehtniriaoteudycaruccatneiciffusnIte and eliminate leaks in the inlet lines.
Reduced flow rate due to a clogged or blocked measuring chamber. Clean the measuring chamber with an appropriate cleaning agent.
ITEM NO PART NO DESCRIPTION ITEM NO PART NO DESCRIPTION
gniRO11-8001511etalpemaN1-800151
gniRO21-8001521bonkteseR2-800152
tsujdassapyB31-8001531revoclanretxE3-800153 ing screw
gulpssapyB41-8001541gulP4-800154
rebmahcgnirusaeM51-8001551wercS5-800155
gniRO61-8001561ylbmessareteM6-800156
gnirpSrednilyC71-8001571wercS7-800157
wercS81-8001581revocydoB8-800158
reveLgnivirD91-8001591ydobre
teM9-800159
etalPraeG02-8001502gniRO01-8001501
21 51008-21 Bevel Pinion shaft
22 51008-22 Cover Sealing Kit
23 51008-23 Bevel Pinion
PROBLEM REMEDY
Leak from the shaft gasket due to damaged gasket. Remove the gear assembly and replace the O Ring (Part No. 51008-22) and the bush.
Insufficient accuracy due to wrong calibration. Repeat calibration following the instructions on Page 1.
Insufficient accuracy due to soiled or blocked measuring chamber. Clean the measuring chamber with an appropriate cleaning agent.
acoL.diulfehtniriaoteudycaruccatneiciffusnIte and eliminate leaks in the inlet lines.
Reduced flow rate due to a clogged or blocked measuring chamber. Clean the measuring chamber with an appropriate cleaning agent.
ITEM NO PART NO DESCRIPTION ITEM NO PART NO DESCRIPTION
gniRO11-8001511etalpemaN1-800151
gniRO21-8001521bonkteseR2-800152
tsujdassapyB31-8001531revoclanretxE3-800153 ing screw
gulpssapyB41-8001541gulP4-800154
rebmahcgnirusaeM51-8001551wercS5-800155
gniRO61-8001561ylbmessareteM6-800156
gnirpSrednilyC71-8001571wercS7-800157
wercS81-8001581revocydoB8-800158
reveLgnivirD91-8001591ydobre
teM9-800159
etalPraeG02-8001502gniRO01-8001501
21 51008-21 Bevel Pinion shaft
22 51008-22 Cover Sealing Kit
23 51008-23 Bevel Pinion
PROBLEM REMEDY
Leak from the shaft gasket due to damaged gasket. Remove the gear assembly and replace the O Ring (Part No. 51008-22) and the bush.
Insufficient accuracy due to wrong calibration. Repeat calibration following the instructions on Page 1.
Insufficient accuracy due to soiled or blocked measuring chamber. Clean the measuring chamber with an appropriate cleaning agent.
acoL.diulfehtniriaoteudycaruccatneiciffusnIte and eliminate leaks in the inlet lines.
Reduced flow rate due to a clogged or blocked measuring chamber. Clean the measuring chamber with an appropriate cleaning agent.
Parts And Drawing Breakdown For The 51008
Ordering Spare Parts
Parts List – Part No. 51008/51008F
Trouble Shooting
2
Visit our website at www.alemlube.com.au Email - [email protected]
NSW
TEL: [phone]
FAX: [phone]
QLD/PNG
TEL: [phone]
FAX: [phone]
VIC/TAS
TEL: [phone]
FAX: [phone]
WA
TEL: [phone]
FAX: [phone]
SA/NT
TEL: [phone]
FAX: [phone]
NZ
TEL: [phone]
FAX: [phone]