Alera ALE-SS600 User manual

ASSEMBLY INSTRUCTIONS
Read these instructions before starting; follow assembly
procedures carefully.
1. Base base 1right-side up on a flat surface or workbench.
Insert support column 2into groove at base. Bumper
stops must be towards rear of sit stand. Align the holes in
support column with holes in base. Insert bolts (4.4) from
outside and fasten down from inside with fiber hex nuts
(4.5) to secure base. Slide shrouds down column to cover
top of base. Shroud should be positioned over hex nuts.
2. lace base on the floor. Slide seat assembly 3onto
support column. ush down front of seat to lock seat
position.
3. Mount handle (4.3) to back of seat assembly. Align holes
in handle with holes in back of seat assembly. Secure
handle with two screws (4.6).
4. Grooves in top of right and left sleeves (4.1) should be
aligned with tabs of handle cover (4.2). Be sure the seat is
facing the correct direction befo e inserting the handle and
handle cover.
WARNING: It is important the tabs in handle engage in
column to ensure that handle locks in place.
Insert handle, handle cover and sleeves (4.2) onto top of
support column. Tap handle into place.
Sit/Stand Se ies
Adjustable height stool
ALE-SS600
PARTS LIST
1 C. 1 C.
1 C. arts bag components
4.1
4.2
4.3
4.4
4.5
4.6
1
4
2
3
ASSEMBLY
STE 1 STE 2
STE 3 STE 4
Slide shrouds down to cover
hex nuts and top of base.
Stool assembled

GENERAL SAFETY INSTRUCTIONS
1. DO NOT STAND ON THIS STOOL. DO NOT USE
STOOL AS A STE LADDER.
2. Use this product only for seating one person at a time.
3. Do not use this stool unless all screws are firmly secured.
4. At least every 4 months, check all screws are firmly
secured.
5. If parts are missing, damaged, broken or worn, stop use of
this product until repairs are made using factory authorized
parts.
6. This stool is designed and intended for users up to 300 lbs.
Use by users above 300 lbs. is not recommended since it
could weaken the stool construction and potentially cause
injury.
7. FAILURE TO FOLLOW THESE WARNINGS COULD
RESULT IN SERIOUS INJURY.
8. Warranty may be void is stool is used while damaged.
Immediately call 1-800-733-4000 and report any problems.
ERGONOMIC FEATURES
To maximize the ergonomic benefits of the Sit/Stand, it is
essential to understand how adjustments effect your
posture.
CAUTION: Make sure you grasp seat handle before lifting
front of seat and adjusting seat height to prevent pinching
of your fingers.
1. Lift seat from under front center of seat to unlock it. Seat
assembly can now slide freely up and down the support
column. Seat assembly is adjustable in height from 223⁄4″
to 323⁄4″. osition seat assembly at a comfortable height in
relation to your body size and the height of the work
surface. Seat should be high enough for you to rest your
weight on while maintaining a slight bend in the knees.
Grasp seat handle to maintain desired seat height. ush
front of seat down completely to lock seat height.
2. Raise handle under right side of seat to tilt seat into
position. Always tilt seat forward to accommodate a
leaning posture. Lower handle to lock seat at desired
angle.
3. added seat is ergonomically contoured and textured for
breathability. osition your weight on center of the seat.
Allow seat to swivel with your body when reaching from
side to side.
MAINTENANCE
Clean polyurethane seat with soap and water. To repair
small cuts in polyurethane, apply a few drops of quick
drying glue in the cut and press sides together until glue
sets. eriodically check faasteners for tightness. Replace
pads if worn.
Raise handle under right
side of seat and tilt seat to
desired angle.
Lower handle to lock seat at
desired angle.
Grasp front of seat with one
hand and handle at back of
seat with other hand. Lift
seat from under front center
of seat to unlock it. osition
seat assembly at desired
height.
Grasp seat handle to main-
tain desired seat height.
ush front of seat down
completely to lock seat
height.