Alfa Network SHD69A User manual

1

User Guide

2

TABLEOFCONTENTS
INTRODUCTION...............................................................................................................3
HARDWARE DESCRIPTION.....................................................................................3
HARDWARE INSTALLATION.....................................................................................4
INITIAL CONFIGURATION.................................................................................................6
CONNECTING TO THE LOGIN PAGE.........................................................................6
STATUS PAGE................................................................................................................7
EASY SETUP...................................................................................................................7
OPERATION MODE -ROUTER................................................................................8
SETTINGS – PPPoE(ADSL).........................................................................8
SETTINGS –STATIC (FIXED IP).....................................................................9
SETTINGS –CABLE/DYNAMIC IP (DHCP)..................................................10
OPERATION MODE -BRIDGE...............................................................................11
OPERATION MODE -WISP..................................................................................12
SETTINGS –STATIC (FIXED IP)...................................................................12
SETTINGS –DHCP (AUTO CONFIG)...........................................................14
SETTINGS –PPPOE(ADSL).......................................................................15
SETTINGS –PPTP.......................................................................................17
SETTINGS –L2TP........................................................................................18
ADVANCED SETUP.......................................................................................................20
MANAGEMENT..............................................................................................21
ADVANCED SETTINGS..................................................................................22
OPERATION MODE.......................................................................................23
FIREWALL CONFIGURATION.................................................................................23
MAC/IP/PORT FILTERING...........................................................................23
VIRTUAL SERVER SETTINGS........................................................................25
DMZ.............................................................................................................26
FIREWALL.....................................................................................................27
CONTENT FILTERING....................................................................................28
NETWORK SETTINGS...........................................................................................29
WAN............................................................................................................29
LAN..............................................................................................................31
ADVANCED ROUTING...................................................................................32
WIRELESS SETTINGS...........................................................................................33
BASIC...........................................................................................................33
SECURITY.....................................................................................................34


3

INTRODUCTION
The SHD69A is a 2x2 MIMO IEEE which support high
through-put up to 300Mbps. It is rain and splash proof when install in upright
position. SHD69A also integrated 11dBi patch antenna and passive PoE for simplify
installation.
HARDWARE DESCRIPTION
Below are SHD69A hardware descriptions
①②
③
① PoE LAN
②
PoE WAN (in Rouer mode )
PoE LAN (in Bridge Mode)
③ Reset
L‐Mount(Option)PoleMountHolders
WallMountHole
WallMountHoleLEDIndicator
Surveillance transmission system

4

HARDWARE INSTALLATION
◆ How to open the sliding door 
Unlatchtheweatherproof
slidingdoorfromtherearof
thebasetoopen.
Slidetheweatherproofsliding
doordownwardsbygriping
ontotheindentedsurfaceof
theweatherproofslidingdoor
andtherear.
Alignthebasewiththe
weatherproofslidingdoor.
Slidetheweatherproof
slidingdoorupwardsuntilit
clicksintoplace.
◆ How to close the sliding door 
◆ How to tie the strap on the pole 

5

◆ Mounting and Radio forward Diagram

StandardPoleMount
*OptionAdjustAntennaL‐Mount
*OptionWallMount

6

INITIAL CONFIGURATION
The SHD69A, 5GHz AP/CPE offers a user-friendly web-based management
interface for the configuration of all the unit’s features. Any
PC directly attached to the unit can access the management interface using a web
browser, such as Internet Explorer (version 6.0 or above).
CONNECTING TO THE LOGIN PAGE
It is recommended to make initial configuration changes by connecting a PC directly
to the SHD69A’s LAN port. The N5 has a default IP address of 192.168.2.1 and a subnet
mask of 255.255.255.0. You must set your PC IP address to be on the same subnet
as the SHD69A (that is, the PC and SHD69A addresses must both start 192.168.2.x). To access
the SHD69A’s management GUI interface, follow these steps:
1. Use your web browser to connect to the management interface using the default
IP address of 192.168.2.1.
2. Log into the interface by entering the default username “admin” and password
“admin,” then click OK.


7

STATUS PAGE
After logging in to the web interface, the Status page displays. The Home page
top-menu-bar shows the Status, Easy Setup, Advanced and Language.



EASY SETUP
The Easy Setup is designed to help you configure the basic settings required to get
the SHD69A up and running. There are only a few basic steps you need to set up the
SHE69A to get the connection.
Click on Easy Setup to bring up the wizard

8

OPERATION MODE -ROUTER
In Router mode, the POE port of the SHD69A will turn into the WAN port. The wireless
interface will become the LAN side. It will turn SHD69A into a wireless router. Since the
Ethernet interface becomes WAN; if your PC is connected to the POE port, the
management IP will change to the WAN IP (192.168.2.1). The remote
management will be automatically turned on to allow you managing the device from
the PoE WAN port..


SETTINGS – PPPoE(ADSL)
1) Select PPPoE to be assigned automatically from an Internet service provider (ISP)
through a DSL modem using Point-to-Point Protocol over Ethernet (PPPoE).



2)

◆ User Name — Sets the PPPoE user name for the WAN port.
(Default: pppoe_user; Range: 1~32 characters)
◆ Password — Sets a PPPoE password for the WAN port.
(Default: pppoe_password; Range: 1~32 characters)

9

◆ Verify Password — Prompts you to re-enter your chosen password.
◆ Operation Mode — Enables and configures the keep alive time and configures the
on-demand idle time.
3)
Security Setup
SSID Choice—ThesamenameofSSID(ServiceSetIdentification)mustbeassignedto
allwirelessdevicesinyournetwork.Consideringyourwirelessnetworksecurity.
Security Mode — Select the security method and then configure the required
parameters. (Options: Disabled, WEP-AUTO, WPA-PSK, WPA2-PSK, WPA-Auto-PSK,
WPA, WPA2, WPA-Auto, 802.1X; Default: Disabled)
SETTINGS –STATIC (FIXED IP)
1) Select Static(Fixed IP), if your Internet service provider (ISP) to be permanent
address on the Internet. A Static IP address is a number (in the form of a dotted
quad)
2)
◆ IP Address — Sets the static IP address.
◆ Subnet Mask — Sets the static IP subnet mask. (Default: 255.255.255.0)

10

◆ Default Gateway — The IP address of a router that is used when the requested
destination IP address is not on the local subnet.
◆ Primary DNS Server — The IP address of the Primary Domain Name Server. A DNS
maps numerical IP addresses to domain names and can be used to identify network
hosts by familiar names instead of the IP addresses. To specify a DNS server, type
the IP addresses in the text field provided. Otherwise, leave the text field blank.
◆ Secondary DNS Server — The IP address of the Secondary Domain Name Server.
3)
Security Setup
SSID Choice—ThesamenameofSSID(ServiceSetIdentification)mustbeassignedto
allwirelessdevicesinyournetwork.Consideringyourwirelessnetworksecurity.
Security Mode — Select the security method and then configure the required
parameters. (Options: Disabled, WEP-AUTO, WPA-PSK, WPA2-PSK, WPA-Auto-PSK,
WPA, WPA2, WPA-Auto, 802.1X; Default: Disabled)
SETTINGS –CABLE/DYNAMIC IP (DHCP)
1) Select Cable/Dynamic IP (DHCP), if your Internet service provider (ISP) use a
DHCP service to assign your Router an IP address when connecting to the
Internet.
2)
The host name that you selected from the DDNS service provider.