EXMAX EX-200N User manual

EXMAX EX-200N Wireless Tour Guide Voice Transmission System
[e-mail] www.iexmax.com EXMAX® Team All Rights Reserved 1/ 4
EXMAX EX-200N Wireless Tour Guide System User Manual
Transmitter:EX-200NT Microphone
1、On-off operation：
●Turn on：Keep pressing the“M" button for 1 second to turn on.
●Turn off：Keep pressing the “M” button for 1 second to turn off.
2、The operation of mute function for transmitter:
When the transmitter is working ,click the “ ”button to mute（the antenna icon "
" on the display screen will change to mute icon “ ” ）,and click again the
“ ”button to restore the speaking function.（the mute icon “ ” will change to
antenna icon " " ）
3、Click one button to turn off all the receivers
Under the working condition, keep pressing the“ ” button for about 5 seconds until the
screen is flashing and the word “OFF” appears, and all the receivers will be forcibly turned
off。（ Note: Now you can click any button of the transmitter to quit or keep pressing the
“M”button to turn off.

EXMAX EX-200N Wireless Tour Guide Voice Transmission System
[e-mail] www.iexmax.com EXMAX® Team All Rights Reserved 2/ 4
4、Who in charge of the devices needs to know how to set the channel ID:
(1) Why and when need to set the channel:
1, When there are two or more groups using the devices at the same location, to avoid
the interference between the groups, you need to set different channels for the
devices (including both transmitters and receivers) of different groups.
2, When you need to add more receivers to a group, and the channel of these added
receivers is not the same as that of the devices of the group, you need to set the
channel of these added receivers to be the same as that of the group.(The channel of
the transmitter and the receivers in a group must be the same，or the receivers can
not receive the signal from the transmitter)
(2) The ways of channel setting:
We have two ways to do this: Wireless channel setting and manual channel
setting.(We will use wireless channel setting if we have to set the channel for many
receivers; And we will use manual channel setting if we have to set the channel for
only a few receivers.)
1、Wireless channel setting:
In the working condition, keep pressing both “ ”button and the“ ” button at
the same time until the channel number on the screen is flashing, then release
both “ ”button and the“ ” button, now the transmitter has entered the
channel setting mode, then you can click the " " or " " button to change
the channel number：The channel number can be changed from 001 to
200,after you have chosen the desired channel number, keep pressing “M"
button for about 3 seconds until the flashing antenna icon " " appears,
then release the “M" button, now the transmitter has entered the wireless
channel matching status, then you can put the receivers(the receivers have
been turned on) closed to the transmitter(within 2 meters),and the receivers’
channel will match the transmitter’s channel(within 5 seconds) and become
the same, now the channel matching is finished. Then you can click the
transmitter’s “M" button to quit the channel matching mode, now if the
transmitter speaks, the receivers can hear it.

EXMAX EX-200N Wireless Tour Guide Voice Transmission System
[e-mail] www.iexmax.com EXMAX® Team All Rights Reserved 3/ 4
2、Manual channel setting:
● Transmitter: Turn on the transmitter, keep pressing the " " button and the "
" button at the same time and don’t release them until the channel number is
flashing, and then you can click the " " button or the " " button to choose
the channel number you want. Then click the “M” button to confirm it.
● Receiver: Turn off the receiver, keep pressing the " + " button and the " "
button at the same time to turn on and don’t release them until the channel number is
flashing, and then you can click the " + " button or the " - " button to choose the
channel number you want. Then click the “ ”button to confirm it.
Receiver:：EX-200NR Earphone
1、On-off operation：
●Turn on：Keep pressing the“ " button for 1 second until the display screen lights up
to turn on.
After it turns on,1、if there’s a transmitter with the same channel speaking nearby
（within about 100 meters),it will hear what the transmitter says; 2、if there’s a
transmitter at the status of channel matching nearby (within about 2 meters),its
channel will match the transmitter’s channel automatically and become the same.
●Turn off：Keep pressing the “ ” button for 1 second to turn off(The display screen
turns off too).You can also use the transmitter’s function “ Click one button to turn off all
the receivers” to turn off the receiver.

EXMAX EX-200N Wireless Tour Guide Voice Transmission System
[e-mail] www.iexmax.com EXMAX® Team All Rights Reserved 4/ 4
2、Volume adjustment:
When the receiver is working, you can click or keep pressing the “+” or“-”button to adjust
the volume.
Attention:
When the transmitters and receivers are not used for a long time, please charge
them every 3 months to keep active, so that the batteries can be protected.
(There is lithium battery inside the device, if it was not used or charged for a
long time, the battery would be damaged.)
User Instruction for Charging Case
1、Power supply：AC 90V--250V
2、When it is going to be charging, take the foam out, and keep the cover
open .
3、When it is charging, the battery level on the display screen of the
transmitters or receivers shows going up, and it stops when the battery
level is full.
4、Normally it takes about 4-5 hours to charge the transmitters or
receivers full.
If you still have any concern, please feel free to contact us, we will reply you immediately.
We provide lifetime quality guarantee for our products.
All the above is trying to make you feel satisfied completely with the purchase, we
could resolve any problem for you. Your understanding would be highly appreciated☺
Have a good day!
Kind Regards
EXMAX
www.iexmax.com
[e-mail]

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment
The devices has been evaluated to meet general RF exposure requirement，the device can be
used in portable exposure condition without estriction