Alico GSDM002LP User manual

INSTALLATION MANUAL
[email protected]
75x75/100x100 32"
MAX
1 8kg
(2. 2~17. 6lbs )
R AT E D
~
GSDM002LP
10’’~15.6’’
MAX
4.5kg
(9.9lbs)
Laptop
1 8kg
(2. 2~17. 6lbs )
R AT E D
~
1~8kg
(2.2~17.6lbs)
Monitor
Dual Monitor Desk Mount

2

Supplied Parts List
3
Arm
A(x2)
Pole
H(x1)
VESA Plate
B(x2)
C-Clamp
G(x1)
Décor Cover
F(x1)
Pole Screw
K(x3)
Top Screw
J(x2)
Tool Holder
I(x1)
Allen Key 3mm
P(x1)
Bottom Grommet Plate
L(x1)
Top Grommet Plate
O(1)
Décor Cover
N(x1)
Screw
M(x4)
Laptop Tray holder
C(x1)
Arm
D(x2)
Cover
E(x2)
Allen Key 6mm
Q(x1)
X 2
M4x12 Bolt
M-A(x4)
M4x16 Bolt
M-B(x4)
M5x12 Bolt
M-C(x4)
M5x16 Bolt
M-D(x4)
D5 Washer
M-E(x4)
Spacer
M-F(x4)

1. Loosen the screws using Allen Key 6mm to adjust the preferred height range option and tighten the screws back.
2. Fix the Décor Cover onto C-Clamp .
4
Step 1
Step 2
Q
FG
C-clamp: Up to 3.1”
Grommet: Up to 1.6”
Option A Clamp Installation
or
1.4"-3.1"
0.4"-1.8"
G
G
F
Q

3. Place the Pole onto the top of C-Clamp , connect Pole and C-Clamp from the bottom using
Pole Screw and tighten with Allen Key 3mm .
5
Step 2
Option A
Clamp Installation
H
G
HG H G
K P
K
P

2. Guide Décor Cover through Pole , place the Pole onto Top Grommet Plate and connect them from the
bottom using Pole Screw and tighten with Allen Key 3mm .
1. Loosen the screws on C-Clamp using Allen Key 6mm firstly, then loosen the screw to release the
hand knob using Screwdriver as shown in second image.(Screwdriver needed but not included)
Q
G
Hand knob
GQ
6
Step 2
Option B
Grommet Base Installation
F H HO
K P
P
O
K
F
H

Grommet Base Installation
Put the Tool Holder and Arm through the Pole , adjust the preferred height and tighten using Allen Key 6mm .
Mark the position of the hole on your mounting surface.
Drill a 3/8"(10mm) diameter hole at the marked position
through the mounting surface. Place the assembled Pole
onto the desk hole, guide the Bottom Gremmet Plate I
through the hand knob. Rotate the knob clockwise to
fasten for stability.
If the existing grommet hole comes with a plastic protector,
remove it to ensure a flat surface before installing the desk
mount. Place the assembled Pole onto the desk hole,
guide the Bottom Grommet Plate I through the hand
knob. Rotate the knob clockwise to fasten for stability.
L
L
3a Existing Grommet Hole Installation
Max 1.6”
H
Hand knob
7
Step 2
Step 3
A
A
I
H
Q
Option B
L
3b Self-drilled Grommet Hole Installation
ø 10mm
(ø ")3/8
I A H Q
L
Max 1.6”
Hand knob
H
Grommet Base Installation
Grommet Base InstallationGrommet Base Installation

intoand Spacer
Grommet Base Installation
3b Self-drilled Grommet Hole Installation
Grommet Base Installation
Grommet Base Installation
8
Step 4
Step 4.3a Step 4.3b
Select M4x12 Bolt M-A or M5x12 Bolt M-C
according to your TV/Monitor, connect VESA Plate B
together with D5 Washer M-E into the mounting
holes on the back of TV/Monitor, tighten with
screwdriver.(Screwdriver needed but not included)
Select M4x16 Bolt M-B or M5x16 Bolt M-D
according to your TV/Monitor, connect VESA Plate B
together with D5 Washer M-E M-F
the mounting holes on the back of TV/Monitor,
tighten with screwdriver.(Screwdriver needed but not
included)
Step 4.1
Select TV Screws
Step 4.2
Select Spacers ( if needed )
B
M-E
M-E
M-C
M-A
Hand thread screws
into the threade d
inserts on the back of
your TV to deter mine
which screw diameter
(M4 or M 5) to use.
M4 M5
M-E
M-F
M-B
M-D
B

1. Attach the Cover E to the Arm D to fix the Arm d on the Laptop Tray Holder c . Please make sure all 4 locks on
each Cover E are engaged with the square holes on the Arm d .
Option A
Monitor mount with a laptop tray holder
9
Step 5
C
D
I
E
D
D
D
D
C
C
B
J
M
2. Put the assembled TV/Monitor onto the Arm A and ensure the stability, tighten the VESA plate using Top Screw G .
AJ
Attach the assembled Loptop Tray Holder C to the VESA plate B and tighten using Screws .
M
B
E
E
C

Option B
Dual Monitor Mount
Step 6
10
Guide the cable through the cable slot and slide the cover back to arm.
Pull the bottom cable slot cover to the VESA direction to detach it off the arm.
A
J
B
Put the assembled TV/Monitor onto the Arm d and ensure the stability, tighten the VESA Plate B using
Top Screw J .
AB
J

Step 8
11
Step 7
For Heavier Monitors
For Lighter Monitors
Manually swivel, tilt or rotate the angle for the best operating environment.
Press the Arm A on horizontal level as image shown, adjust gas spring tension to your personal preference using Allen Key 6mm ,
adjust the tilt tension using Allen Key 6mm P .
±135°
±180°
±90°
±180°
Q
A
Q
Q
Q

1-844-SATTLER (18447288537) [email protected]
If you have any questions,please contact us.
We support the technology that brings your home to life.
We offer high quality products, professional customer service,
and extensive technical support.