ALL SPORTS Yamaha Drive Rear Flip Seat Kit User manual

Yamaha Drive Rear Flip Seat Kit
instruction manual
1-866-291-5244

Installation
1. Unbolt supports.
4
Parts not shown in proportion.
Remove bolts connecting roof supports
to roof.
Remove bolts connecting gutters to
roof supports.
Installation
2. Remove gutters and roof supports.
4
Parts not shown in proportion.
Remove bolts connecting roof supports
to bag holder.
Save for re-use.
Raise roof and remove gutters by
sliding upwards.
Installation
3. Remove seat cushion and access panel.
4
Parts not shown in proportion.
Remove rivets connecting access panel
to body.
Remove bolts connecting seat cushion
to bag holder.
Save for re-use.
Installation
4. Remove Bag holder.
6
Parts not shown in proportion.
Remove bolts connecting bag holder to
horizontal frame bars located underneath the body.
3
Installation
1. Unbolt Supports. 2. Remove gutters and roof supports.
3. Remove seat cushion and access panel. 4. Remove bag holder.
Parts not shown in proportion.

Installation
5. Install frame supports and access panel.
7
Parts not shown in proportion.
Remove existing bolts in bagwell.
Drill holes to 3/8”. Bolt rear frame support
to bagwell using 5/16”x 2” bolts,
washers, and nuts.
Bolt front supports to front horizontal frame
bar using factory hardware.
re-install access panel
using factory hardware.
Installation
6. Install flip seat frame.
7
Parts not shown in proportion.
Bolt rear supports to underside of
ip seat frame with 5/16”x 1” bolts,
at washers, and nuts.
Bolt front supports to outer side of
ip seat frame with 5/16”x 1” bolts,
at washers, and nuts.
Installation
7. Install Side Frames.
8
Parts not shown in proportion.
Bolt side frames to rear of ip seat frame
with 5/16” x 1 1/2” bolts, at washers,
and acorn nuts.
Bolt side frames to front of ip seat frame
with 5/16” x 1 1/2” bolts, at washers,
and nyloc nuts.
Installation
8. Install back frame.
9
Parts not shown in proportion.
Bolt back frame to side frames with
5/16” x 2 1/2” bolts, at washers,
and nyloc nuts.
Bolt back frame to front supports with
5/16” x 1 1/2” bolts, at washers,
and nyloc nuts.
Installation
5. Install frame supports and access panel. 6. Install flip seat frame.
7. Install side rails. 8. Install back frame.
Parts not shown in proportion. 4

Installation
9. Install step plate.
10
Parts not shown in proportion.
Bolt step plate supports loosely
to step plate with 5/16”x 2”bolts(2),
at washers(2), and nuts(2).
Bolt step plate to side frames
with 5/16” x 2 1/2” bolts(2),
at washers(2), and nuts(2).
connect step plate supports to rear
supports with 5/16” x 1” bolts,
at washers, and nuts.
Installation
10. Install roof supports and seat cushion.
12
Parts not shown in proportion.
Bolt roof supports to front frame supports
using 1/4” x 2 1/2” bolts, at washers,
and nyloc nuts.
Bolt Seat cushion to front frame supports
using factory hardware.
Installation
11. Install Gutters.
12
Parts not shown in proportion.
Slide gutter in place and bolt to roof
supports using factory hardware.
Bolt roof supports to roof using
factory hardware.
Installation
12. install rear seat pad.
12
Parts not shown in proportion.
Bolt rear seat supports to back of
rear seat back pad with 1/4”x 1” bolts
and at washers.
BBolt rear seat back pad to underside of
back frame with 1/4” x 1 3/4” bolts,
at washers, and nuts.
Installation
9. Install step plate. 10. Re-install roof supports and seat cushion.
11. Re-install gutters. 12. Install rear seat back cushion.
Parts not shown in proportion. 5

Installation
13. install flip-seat pad.
6
Parts not shown in proportion.
Attach ip seat pad to underside of cargo
panel with allen bolts(8). Secure seat pull
in between pad and panel.