ALL LINK-LIGHT AL100 User manual

LINK-LIGHT
Operating Guide AL100
05/22

Ref: FM/AL100/operating/29/04/21
6x Lane Controller (AL100)
Operating guide (page 1/2) www.allltd.uk.com
Button currently
not functional
OPERATING GUIDE
DIRECT CONTROL Buttons - override features
AUTO
Turn ON Run set programmes - ON position (button-GREEN)
FULL & OFF
ON/OFF All lights & ZONES
MANUAL
Press-1 Direct control SINGLE lighting ZONE (one ZONE at a time)
Press-2 Direct control ALL lighting ZONES
CATCH
CATCHING Low light level setting - easy to adjust Power & ZONES
PROGRAMMING Buttons (and programming) - Ensure AUTO button is ON (green)
CLOCK
Press/HOLD Button “flash - Adjust with UP/Down buttons - Press SET to save
PROG
Programming
Press-1 View Programmes “flash-WHITE - scroll programmes with button
Press/HOLD Programming mode “flash-GREEN
Programming sequence:
ZONES Press ZONE buttons directly GREEN active - RED inactive (off)
Time settings Set ON/OFF programme times Press SET
Power-Level Set the required light power-level Press SET
FADE Dusk-Dawn, options 10sec -to- 30mins Press SET
Up/Down Adjust: Clock, Programme Time, Power-Level, Fade, etc
SET
Save/Store Press to save that update & move to next step (when required)
Light sensor OPTIONAL EXTRA - see instructions (No function if not installed)
ZONES Buttons (lighting lanes)
ZONE (1- 6)
Light ZONE GREEN Active - RED Inactive, within the current/selected programme
Quick by-pass features
Power-Level You can adjust the Power whilst in the PROG-button “flash” WHITE -view programme mode
(light level) Press Up/Down-Buttons to adjust > Remember to press SET to save your amend
ZONES You can adjust ZONES whilst in the PROG-Button “flash” WHITE -view programme mode
(light lanes) Active (GREEN) / inactive (RED)> Remember to press SET to save your amend

Ref: FM/AL100/operating/29/04/21
Programme Run / View
Programme Setting Page 2/2
Run programmes AUTO - BUTTON
Ensure this button is turned ON (illuminate GREEN), must be ON to run programmes (& features)
View programmes PROG - BUTTON
Press “once”- button “flashes” WHITE (“flash” WHITE indicates view programmes mode)
View/Scroll, Press until you reach Prog’ number: 1,2,4,5,6,7,8,9,10 (remains “flash” WHITE)
Step 1 PROG –BUTTON (ensure AUTO button is ON - see above)
Programming Press/HOLD –PROG Button until “Flash” GREEN -indicating programming mode is activated
Step 2 ZONES - BUTTONS (select lighting lanes required)
Press ZONE buttons to activate the ZONE (lighting lane) required within this selected programme
ZONE - Button indicators: GREEN Active / RED Inactive (RED indicates not required, not active)
Note: Press the ZONE Buttons directly - do NOT press SET button, ZONES are set freely in this mode.
When ZONES are selected move to setting the programme times –PROG Button remains “flashing”
Step 3 PROGRAMMES TIMES (24hr clock) -Use Up/Down-Buttons to adjust the Programme Times
ON-Time: HOUR digits should “flash” “00”:00 > Press SET-Button to save (& move to next)
Repeat the process for ON-Time Min’s “00:”00 > Press SET-Button to save (& move to next)
OFF Time: Hour digits should “flash” “00”:00 > Press SET-Button to save (& move to next
Repeat the process for OFF-Time Min’s “00:”00”> Press SET-Button to save (& move to >> )
Step 4 POWER-LEVEL (Selected ZONE - lighting lanes, light levels)
The LCD screen large digits will “Flash” -POWER should be highlighted on the screen
Press the Up/Down-Buttons to select POWER-LEVEL > Press SET-button to save (& move to >>)
Step 5 FADE (dusk-to-dawn)
The LCD screen large digits will “Flash” -FADE should be highlighted on the screen
Press the Up/Down-Buttons to select FADE rate time > Press SET-button to save (& move on)
(Programme sequence completed)
Programme set
In the vent of error simply press AUTO button to escape & start again !!
***
More Prog’s Set more programmes - REPEAT above steps for each programme setting 1-10
CANCEL You can Cancel/Clear any programme
Programmes PROG-Button (view mode - button “flash” WHITE)- select the programme required >> then >>
Press both-together Up/Down-Buttons (at the same time) –this PROG will cancel/clear
Time-out Time out feature “30sec” - if you take too long the system will self-cancel (need to re-start)
Programme Programming priority - cascading from 10-to-1
(priorities) Example 1: Programme PROG-10 will override any other Programme number (all lower programmes)
Example 2: Programme set in PROG-5 will override any Programme below in 1,2,3,4 (not higher)
General info’
Screen view
Override’s
Power-Cut
Memory
AUTO only displays time & current programme/s running - Press PROG to view
After using override buttons, Press AUTO to return system run-programmes
System reverts to AUTO after a power-cut event (default setting)
Programme memory battery - Periodically change battery behind LCD screen