dixell XWA11V User manual

dIXEL&
Operating Instructions XWA11V
1598003200
Weiss Instruments, Inc. 905 Waverly Ave. Holtsville, NY 11742 631-207-1200 www.weissinstruments.com
1
XWA11V
Walk-In Temp / Door /Alarm / Light Module
1. GENERAL DESCRIPTION
Model XWA11V, 100x64 mm format, is a microprocessor-based controller, suitable for temperature
monitoring and alarming in a walk-in cooler or freezer. It is provided with two (2) Dry Contacts to control lights
and an external alarms. It is provided with one (1) NTC probe input for temperature measurement. The unit
has 2 Digital Inputs, one for a Door Switch and the 2nd as an optional Panic Switch. See the catalog for
optional accessories. One 5Pin Input allows the user to program the parameter list with a “Hot Key” (see
section 9)
Note: The default settings are listed in the back of this manual. They are set for Coolers (Medium
Temp). For Freezers (Low Temp) you MUST Change the ALL and ALU settings. See Section 4.0
2. GENERAL WARNINGS
2.1 PLEASE READ BEFORE USING THIS MANUAL
•This manual is part of the product and should be kept close to the instrument for easy and quick
reference.
•The instrument shall not be used for purposes different from those described hereunder. It cannot be used
as a safety device.
•Check the application limits before proceeding.

dIXEL&
Operating Instructions XWA11V
1598003200
Weiss Instruments, Inc. 905 Waverly Ave. Holtsville, NY 11742 631-207-1200 www.weissinstruments.com
2
2.2 SAFETY PRECAUTIONS
•Check if the supply voltage is correct before connecting the instrument.
•Do not expose the back of the instrument to water or moisture: use the controller only within the operating limits
avoiding sudden temperature changes with high atmospheric humidity to prevent the formation of condensation.
•Warning: disconnect all electrical connections before performing any maintenance operation.
•Fit the probe where it is not damaged by the end-user. The instrument must not be opened.
•In case of failure or faulty operation send the instrument back to the distributor (see address) with a detailed
description of the fault.
•Consider the maximum current that can be applied to each relay (see Technical Data).
•Ensure that the wires for probes, loads and the power supply are separated and far enough from each other, without
crossing or intertwining.
3. INTERFACE
LOW HIGH
KEY FRONT PANEL OPERATION
In Programming Mode press to select a parameter or to confirm an operation.
Press and hold this key for more than 5 s to turn the controller OFF.
Press and hold this key for more than 1 s to turn the controller back ON.
HIGH
Press to see the HIGH Temp ALARM (ALU parameter)
LOW
Press to see the LOW Temp ALARM (ALL parameter)
In Programming Mode press to browse parameter codes.
Press to increase the displayed value.
Press to mute the buzzer (+ relay) when an ALARM is happening.
Hot key programming: with the instrument on, insert the hot key and then press
the UP button.
In Programming Mode press to browse parameter codes.
Press to decreases the displayed value.
Switch ON and OFF the light of the cold room
KEY COMBINATIONS: PRESS SIMULTANEOUSLY
+
To lock and unlock the Keyboard.
+
To enter the Programming Mode.

dIXEL&
Operating Instructions XWA11V
1598003200
Weiss Instruments, Inc. 905 Waverly Ave. Holtsville, NY 11742 631-207-1200 www.weissinstruments.com
3
+
To exit the Programming Mode.
+
HIGH
To enter a new value for the HIGH Temp ALARM (ALU).
+
LOW
To enter a new value for the LOW Temp ALARM (ALL).
3.1 USE OF LEDS
Each LED function is described in the following table:
LED
MODE
Function
ON
ALARM signaling
ON
The light is on
°C
ON
Celsius degrees operation
°F
ON
Fahrenheit degrees operation
4. TEMP ALARMS SETTING
4.1 HOW TO SET THE MIN TEMPERATURE ALARM
•To modify the minimum (LOW) Temp ALARM: hold the +
LO W
keys pressed for 3 s until the
minimum Temp alarm is displayed.
•Change the value using the UP and DOWN keys.
•Press the SET key to confirm the new value and exit.
4.2 HOW TO SET THE MAX TEMPERATURE ALARM
•To modify the max (HIGH) Temp ALARM: hold the +
HIGH
keys pressed for 3 s until the max Temp
alarm is displayed.
•Change the value using the UP and DOWN keys.
•Press the SET key to confirm the new value and exit.
5. PROGRAMMING
5.1 HOW TO CHANGE A PARAMETER VALUE MAIN MENU
1. Enter the Programming Mode by pressing the SET and DOWN key for 3s ( and will start blinking).
2. Select the required parameter. By using the UP or DOWN KEY
3. Press the “SET” key to display its value (now only the LED is blinking).
4. Use “UP” or “DOWN” to change its value.
Press “SET” to store the new value and move to the following parameter.
To exit: Press SET + UP or wait 15 s without pressing a key.
NOTE: the set value is stored even when the procedure is exited, by waiting the time-out to expire.
5.2 THE HIDDEN MENU (PR2)
The hidden menu includes all the parameters of the instrument.
5.2.1 HOW TO ENTER THE HIDDEN MENU (PR2)
1. Enter the Programming Mode by pressing the Set + down key for 3s ( and starts blinking).
2. When a parameter is displayed, release and re-press the SET + down for more than 7s.
3. The Pr2 label will be displayed immediately followed from the HY parameter. NOW YOU ARE IN THE
HIDDEN MENU.
4. Select the required parameter as above
5. Press the “SET” key to display its value (Now only the LED is blinking).
6. Use “UP” or “down” to change its value.
7. Press “SET” to store the new value and move to the following parameter.
To exit: Press SET + up or wait 15s without pressing a key.
NOTE: the set value is stored even when the procedure is exited by waiting the time-out to expire.

dIXEL&
Operating Instructions XWA11V
1598003200
Weiss Instruments, Inc. 905 Waverly Ave. Holtsville, NY 11742 631-207-1200 www.weissinstruments.com
4
5.2.2 HOW TO MOVE A PARAMETER FROM THE HIDDEN MENU TO THE FIRST LEVEL AND
VICEVERSA
Each parameter present in the HIDDEN MENU can be removed or put into “THE FIRST LEVEL” (user level)
by pressing “SET + down”.
In HIDDEN MENU when a parameter is present in First Level the decimal point LED is on.
5.3 HOW TO LOCK THE KEYBOARD
1. Keep pressed for more than 3s the UP and DOWN keys.
2. The “POF” message will be displayed and the keyboard will be locked. At this point it will be possible
only to see the Set Point or the MAX o MIN Temp stored
3. If a key is pressed more than 3s the “POF” message will be displayed.
5.4 TO UNLOCK THE KEYBOARD
Keep pressed together for more than 3s the UP and DOWN keys. The “PON” message is displayed
6. LIGHT MANAGEMENT
6.1 TIMED REGULATION: I1L = Y
With i1L = y the light remains on at least for the LHt parameter.
The LHt timer is re-initialized every time the light button is pushed.
With LHt=0 the light remains on until the light button is pushed again.
The light is switched on every time one of the following conditions happens:
•the door is open (i1F = dor)
•the presence sensor is activated (i2F = LHt)
•the light button is pushed
The light is switched off when all the following conditions happen:
•the LHt timer is exhausted
•the door is closed (i1F = dor)
•the presence sensor is de-activated (i2F = LHt)
•Light button regulation: i1L = n
The light button has a higher priority than digital inputs therefore:
- if the light was switched on by button the digital input can not modify its status.
- if the light was switched on by digital input, the light button can modify its status.
7. INSTALLATION AND MOUNTING
7.1 MOUNTING OF XWA11V – PR10000
The XWA11V must be mounted on vertical
panel, in a J-Box or wall mount using the
VS-BOX2
The Ambient Temp range for correct
operation is 32 – 140°F. Avoid installation in
places subject to strong vibrations, corrosive
gases, excessive dirt or humidity. The same
recommendations apply to probes.
8. ELECTRICAL CONNECTIONS
The instrument is provided with screw terminal blocks to connect cables with a cross section up to 2,5 mm2
for the digital and analog inputs. Relays and power supply have a Fast-on connection (6,3mm). Heat-
resistant cables have to be used. Before connecting cables make sure the power supply complies with the

dIXEL&
Operating Instructions XWA11V
1598003200
Weiss Instruments, Inc. 905 Waverly Ave. Holtsville, NY 11742 631-207-1200 www.weissinstruments.com
5
instrument requirements. Separate the probe cables from the power supply cables, from the outputs and the
power connections. Do not exceed the maximum current allowed on each relay and in case of heavier loads
use a suitable external relay.
N.B. Maximum current allowed for all the loads is 15A.
8.1 PROBE CONNECTIONS
The probe shall be mounted with the bulb upwards to prevent damages due to casual liquid infiltration. It is
recommended to place the thermostat probe away from air streams to correctly measure the average room
temperature. The probe can be extended up to 300 ft. Check calibration when running long lengths over
100ft.
9. USE OF THE PROGRAMMING “HOT KEY “
9.1 HOW TO PROGRAM A HOT KEY FROM THE INSTRUMENT (UPLOAD)
1. Program one controller with the front keypad.
2. When the controller is ON, insert the “Hot key” and push UP key; the "uPL" message appears followed a
by flashing “End”
3. Push “SET” key and the End will stop flashing.
4. Turn OFF the instrument remove the “Hot Key”, then turn it ON again.
NOTE: the “Err” message is displayed for failed programming. In this case push again okey if you want to restart
the upload again or remove the “Hot key” to abort the operation.
9.2 HOW TO PROGRAM AN INSTRUMENT USING A HOT KEY (DOWNLOAD)
1. Turn OFF the instrument.
2. Insert a programmed “Hot Key” into the 5 PIN receptacle and then turn the Controller ON.
3. Automatically the parameter list of the “Hot Key” is downloaded into the Controller memory, the “doL”
message is blinking followed a by flashing “End”.
4. After 10 seconds the instrument will restart working with the new parameters.
5. Remove the “Hot Key”..
NOTE the message “Err” is displayed for failed programming. In this case turn the unit off and then on if you want
to restart the download again or remove the “Hot key” to abort the operation.
10. ALARM SIGNALS
Message
Mode
Cause
Outputs
“P1”
Flashing
Probe failure
Alarm output ON
“PoF”
Flashing (3s)
Keyboard locked
Not changed
“Pon”
Flashing (3s)
Keyboard un-locked
Not changed
“HA”
Alternated with temp
Maximum T° alarm
Alarm output ON;
“LA”
Alternated with temp
Minimum T° alarm
Alarm output ON;
“dA”
Alternated with temp
Door switch alarm
Alarm output ON;
“EA”
Alternated with temp
External alarm
Alarm output ON;
“PAn”
Alternated with temp
Serious external alarm
Alarm output ON;
dEF
Alternated with temp
Defrost is running
Not changed
The alarm message is displayed until the alarm condition is reset.
Silencing buzzer
Once the alarm signal is detected the buzzer can be silenced by pressing the UP key.
10.1 ALARM RECOVERY
Probe alarms : “P1” (probe1 faulty), “P2” ; they automatically stop 10s after the probe restarts normal
operation. Check connections before replacing the probe.
T°alarms “HA” and “LA” automatically stop as soon as the thermostat T° returns to normal values or when
the defrost starts.
Door switch alarm “dA” stops as soon as the door is closed.
External alarms “EAL”, “BAL” stops as soon as the external digital input is disabled.

dIXEL&
Operating Instructions XWA11V
1598003200
Weiss Instruments, Inc. 905 Waverly Ave. Holtsville, NY 11742 631-207-1200 www.weissinstruments.com
6
11. TECHNICAL DATA
Housing: self extinguishing ABS
Case: face 100x64 mm; depth 45.5mm
Mounting: J-box or wall-mount option
Frontal protection: IP65
Connections: ¼” fast-on for power, 1/8” fast-on for probes and Digital Inputs
Power supply: 120Vac ±10%, optional 230Vac ±10%
Power absorption: 4VA max.
Display: 3 digits, red LED, 14,2 mm high.
Inputs: 1 NTC probe
Digital inputs: 2 free voltages
Relay outputs: Dry Contacts
Light: relay SPST 16A, 120Vac;
Alarm: relay SPST 8A, 120Vac
Other output: alarm buzzer
Data storing: on the non-volatile memory (EEPROM).
Measuring and regulation range:
NTC probe: -40÷110°C (-58÷230°F)
Resolution: 1 °F
Accuracy : ±1 °F
12. CONNECTIONS
Power supply: 120Vac +/- 10% 15A MAX current
Full P/N Ambient Temp / %RH
Date Code

dIXEL&
Operating Instructions XWA11V
1598003200
Weiss Instruments, Inc. 905 Waverly Ave. Holtsville, NY 11742 631-207-1200 www.weissinstruments.com
7
13. PARAMETER MAP
LABEL
DESCRIPTION
COOLER
VALUES
DEFAULT
**
FREEZER
VALUES
LEVEL
RANGE
ot
Thermostat probe calibration
0
0
Pr2
[-12,0°C <> 12,0°C] [-
21°F <> 21°F]
CF
Temp measurement unit
F
F
Pr2
°C - °F
rES
Resolution (only °C)
in
in
Pr2
dE - in
UT
Display update
60
60
Pr2
0 <> 255 (sec)
OnF
Off function enabling
Y
Y
Pr2
N - Y
ALU
High Temp alarm setting **
50
30
Pr1
°C[ ALL <> 150,0°]
°F[ ALL <> 302°]
ALL
Low Temp alarm setting **
25
-20
Pr1
°C[ -50.0° <> ALU]
°F[-58 <> ALU]
AFH
Temp alarm differential
2
2
Pr2
[0,1°C <>25,5°C]
[1°F <> 45°F]
ALd
Temp alarm delay
30
30
Pr1
0 <> 255 (min.)
dAo
Delay of Temp alarm at start-up
1.5
1.5
Pr2
0 <> 24.0 (Hrs / 10 min.)
EdA
Alarm delay at the end of defrost
30
30
Pr2
0 <> 255 (min.)
dot
Delay of Temp alarm after closing
the door
15
15
Pr2
0 <> 255 (min.)
LHt
Light timer
15
15
Pr1
0 <> 255 (min.)
doA
Open door alarm delay
15
15
Pr1
0 <> 255 (min.)
OA1
First relay configuration
Alr
ALr
Pr2
ALr - LHt - OnF
oA2
Second relay configuration
LHt
LHt
Pr2
ALr - LHt - OnF
AOP
Alarm relay polarity
CL
CL
Pr2
OP - CL
i1P
Digital input 1 polarity
op
oP
Pr2
OP - CL
i1L
Door switch to turn light ON
y
y
Pr2
n - Y
i1F
Digital input 1 operating mode
dor
dor
Pr2
EAL - dor- dFr - LHt
i2P
Digital input 2 polarity
CL
cL
Pr2
OP - CL
i2F
Digital input 2 operating mode
Pan
PAn
Pr2
EAL - Pan - dFr - LHt
did
Time interval/delay for digital
input alarm
0
0
Pr2
0 <> 255 (min.)
tbA
Alarm relay disabling
n
n
Pr2
n - Y
PbC
Kind of probe
ntc
ntc
Pr2
PtC - ntC
dP1
Real T° Probe 1
Pr2
(probe value)
rEL
FW release
Pr2
read only
Ptb
Parameter map
Pr2
read only

dIXEL&
Operating Instructions XWA11V
1598003200
Weiss Instruments, Inc. 905 Waverly Ave. Holtsville, NY 11742 631-207-1200 www.weissinstruments.com
8
14. PARAMETER LIST
Ot Thermostat probe calibration: (-12.0÷12.0°C/ -21÷21°F) allows to adjust possible offset of the
thermostat probe.
CF T measurement unit: °C = Celsius; °F = Fahrenheit. When the measurement unit is changed the Set
Point and the values of some parameters have to be modified.
rES Resolution (for °C): (in = 1°C; dE = 0.1 °C) allows decimal point display.
Ut Display update: The time delay of the T readout (0÷255s)
onF Off function enabling: n = off function disabled; y = off function enabled;
ALU High T°alarm setting: (ALL ÷150°C or 302°F);
when this T° is reached and after the ALd delay time the HA alarm is enabled.
ALL Low T°alarm setting: (- 50°C or -58°F ÷ALU)
when this T° is reached and after the ALd delay time, the LA alarm is enabled,.
AFH T°alarm differential: (0,1÷25,5°C; 1÷45°F) differential for T° alarm Set Point and fan regulation Set
Point, always a positive value
ALd T°alarm delay: (0÷255 min) time interval between the detection of an alarm condition and the
corresponding alarm signaling.
dAO Delay of T°alarm at start-up: (0min÷23h 50min) time interval between the detection of the T° alarm
condition after the instrument power on and the alarm signaling.
EdA Alarm delay at the end of defrost: (0÷255 min) Time interval between the detection of the T° alarm
condition at the end of defrost and the alarm signaling.
dot Delay of T°alarm after closing the door: (0÷255 min) Time delay to signal the T° alarm condition
after closing the door.
LHt Light timer: (0-255 min) The time the light will stay on after pressing the light switch on the keyboard.
doA Open door alarm delay:(0÷255 min) delay between the detection of the open door condition and its
alarm signaling: the flashing message “dA” is displayed.
oA1 First relay configuration: (14-15): ALr = alarm; LHt = light; onF = on/off relay
oA2 Second relay configuration: (14-16): ALr = alarm; LHt = light; onF = on/off relay
AOP Alarm relay polarity: cL = closing contacts; oP = opening contacts.
i1P Digital input 1 polarity (1-2): CL : the digital input is activated by closing the contact;
OP the digital input is activated by opening the contact
i1L Door switch to turn light ON(1-2): (y / no) To turn the light ON automatically when the door is open.
The light will turn off based on LHt . Keyboard switch must be turned ON first.
i1F Digital input 1 operating mode(1-2): EAL = external alarm; dor = door switch; dFr = A defrost is
running; LHt = keep light ON (signal from occupancy sensor) override LHt.;
i2P Digital input 2 polarity (1-3): CL : the digital input is activated by closing the contact;
OP the digital input is activated by opening the contact
i2F Digital input 2 operating mode: configure the digital input function:
EAL = External alarm;
PAn =Panic alarm;
dFr = A defrost is running;
LHt = Keep light ON (signal from occupancy sensor) override LHt.
did Time interval/delay for digital input alarm:(0÷255 min.) If I2F=EAL or PAn (external alarms), “did”
parameter defines the time delay between the detection and the successive signaling of the alarm.
tbA Alarm relay & Buzzer disabling: (y ; no)
Pbc Type of probe (PTC, NTC)
dP1 Probe 1 T
rEL Software release for internal use.
Ptb Parameter table code: read only.