Allied Telesis AT-AR3050S User manual

C613-04069-00 REV A
AT-AR3050S
AT-AR4050S
Installation Guide
CLASS 1
LASER PRODUCT
CONSOLE
SD
SD
FAU LT
PWR
FNC1
FNC2
RESET
1234
56
78 12
BYPASS 12
12
USB
HA
FDX HDX COL
READY FAU LT
READY FAU LT
MASTER STANDBY
ETH
ETH
AR3050S
1000 LINK ACT 100 LINK ACT
AR3050S
CLASS 1
LASER PRODUCT
CONSOLE
SD
SD
FAU LT
PWR
FNC1
FNC2
RESET
1234
56
78 12
BYPASS 12
12
USB
HA
FDX HDX COL
READY FAU LT
READY FAU LT
MASTER STANDBY
ETH
ETH
AR4050S
1000 LINK ACT 100 LINK ACT

Copyright 2015 Allied Telesis, Inc.
All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc.
Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names,
logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners.
Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior
written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for
any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related
to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the
possibility of such damages.

3
Electrical Safety and Emissions Standards
This product meets the following standards.
EMC: AS/NZS CISPR22 class A, EN55022 Class A, EN55024, EN61000-3-2, EN61000-3-3, FCC
Part 15 (CFR 47) Class A, ICES-003, VCCI-A
Electrical Safety: IEC 60950-1, CAN/CSA-C22.2 No.60950-1, EN60950-1, UL 60950-1
Environmental Compliance: 2011/65/EU RoHS Directive
U.S. Federal Communications Commission
Radiated Energy
Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15
of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with this instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to operate
this equipment.
Industry Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Warning: In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
Laser Safety EN60825-1

4
Translated Safety Statements
Important: Safety statements that have the symbol are translated into multiple languages in the
Translated Safety Statements document at www.alliedtelesis.com/support.

5
Preface .............................................................................................................................................................................. 11
Document Conventions .............................................................................................................................................. 12
Contacting Allied Telesis ............................................................................................................................................ 13
Chapter 1: Overview ......................................................................................................................................................... 15
Features ..................................................................................................................................................................... 16
10/100/1000 Mbps Twisted Pair Ports ................................................................................................................ 16
WAN Ports .......................................................................................................................................................... 16
USB Port ............................................................................................................................................................. 16
USB Retainer Slot ............................................................................................................................................... 16
SD Card Slot ....................................................................................................................................................... 16
Reset Button ....................................................................................................................................................... 16
High Availability ................................................................................................................................................... 16
LEDs ................................................................................................................................................................... 16
Kensington lock hole ........................................................................................................................................... 17
Installation Options .............................................................................................................................................. 17
Management Software and Interfaces ................................................................................................................ 17
Management Methods ........................................................................................................................................ 17
Package Contents ...................................................................................................................................................... 18
Front and Back Panels ............................................................................................................................................... 19
Management Panel .................................................................................................................................................... 21
Management Software ............................................................................................................................................... 22
Twisted Pair Ports ...................................................................................................................................................... 23
WAN Ports .................................................................................................................................................................. 24
ETH Ports (RJ-45) ............................................................................................................................................... 24
ETH Ports (SFP) ................................................................................................................................................. 24
Bypass Ports ....................................................................................................................................................... 24
LEDs ........................................................................................................................................................................... 26
Power LED .......................................................................................................................................................... 26
Fault LED ............................................................................................................................................................ 26
High Availability LED ........................................................................................................................................... 27
USB LED ............................................................................................................................................................. 28
SD Card LED ...................................................................................................................................................... 29
LEDs for the ETH 1 and ETH 2 Ports (RJ-45) ..................................................................................................... 30
LEDs for the Twisted Pair LAN Ports .................................................................................................................. 31
LEDs for the ETH 1 and ETH 2 Ports (SFP) ....................................................................................................... 33
Function 1 LED ................................................................................................................................................... 33
Function 2 LED ................................................................................................................................................... 34
USB Port .................................................................................................................................................................... 35
USB Retainer Slot ...................................................................................................................................................... 36
SD Card Slot .............................................................................................................................................................. 39
Console Port ............................................................................................................................................................... 40
Reset Button ............................................................................................................................................................... 41
Power Supply ............................................................................................................................................................. 42
Chapter 2: Beginning the Installation ............................................................................................................................. 43
Reviewing Safety Precautions .................................................................................................................................... 44
Choosing a Site for the Routers ................................................................................................................................. 48
Unpacking the Router ................................................................................................................................................. 49
Contents

Contents
6
Chapter 3: Installing the Router and Powering on the Router ..................................................................................... 51
Installing the Router on a Table or Desktop ............................................................................................................... 53
Chapter 4: Cabling the Networking Ports ....................................................................................................................... 67
Cabling the Twisted Pair Ports ................................................................................................................................... 68
Chapter 5: Troubleshooting ............................................................................................................................................. 73
Appendix A: Technical Specifications ........................................................................................................................... 77
Physical Specifications ................................................................................................................................................ 77
Environmental Specifications....................................................................................................................................... 77
Power Specifications ................................................................................................................................................... 78
Certifications................................................................................................................................................................ 78
RJ-45 Twisted Pair Port Pinouts.................................................................................................................................. 79
RJ-45 Style Serial Console Port Pinouts ..................................................................................................................... 80

7
Figure 1: Front panel of the AT-AR3050S router..................................................................................................................19
Figure 2: Front panel of the AT-AR4050S router..................................................................................................................19
Figure 3: Back panel of the AT-AR3050S and AT-AR4050S routers ...................................................................................20
Figure 4: AT-AR3050S and AT-AR4050S management panel ............................................................................................21
Figure 5: Power LED ............................................................................................................................................................26
Figure 6: Fault LED ..............................................................................................................................................................27
Figure 7: HA LED .................................................................................................................................................................27
Figure 8: USB LED ...............................................................................................................................................................28
Figure 9: SD Card LED.........................................................................................................................................................29
Figure 10: ETH Port (RJ-45) LEDs.......................................................................................................................................30
Figure 11: LEDs for the 10/100/1000Base-T Ports...............................................................................................................32
Figure 12: LEDs for ETH 1 and ETH 2 Ports (SFP) .............................................................................................................33
Figure 13: Function 1 LED....................................................................................................................................................34
Figure 14: Function 2 LED....................................................................................................................................................34
Figure 15: USB port..............................................................................................................................................................35
Figure 16: USB retainer slot .................................................................................................................................................36
Figure 17: USB retainer........................................................................................................................................................37
Figure 18: Attaching the USB retainer..................................................................................................................................37
Figure 19: Attaching the cable tie .........................................................................................................................................38
Figure 20: SD card slot.........................................................................................................................................................39
Figure 21: Console port ........................................................................................................................................................40
Figure 22: Reset button ........................................................................................................................................................41
Figure 23: Components of the AT-AR3050S and AT-AR4050S routers...............................................................................49
Figure 24: Power cord retaining clip .....................................................................................................................................52
Figure 25: Inserting the retaining clip into the retaining bracket ...........................................................................................52
Figure 26: Attaching the rubber feet .....................................................................................................................................54
Figure 27: Turning the router upside down...........................................................................................................................55
Figure 28: Removing the rubber feet....................................................................................................................................56
Figure 29: Attaching handles to the brackets .......................................................................................................................56
Figure 30: Attaching the equipment rack brackets ...............................................................................................................57
Figure 31: Mounting the router horizontally in an equipment rack........................................................................................57
Figure 32: Attaching the wall mount brackets to the side of the router.................................................................................59
Figure 33: Making the anchor hole locations ........................................................................................................................60
Figure 34: Securing the router to the wall.............................................................................................................................61
Figure 35: Power cord retaining clip in the up position.........................................................................................................62
Figure 36: Connecting the AC power cord............................................................................................................................63
Figure 37: Connecting the Management Cable to the Console Port ....................................................................................64
Figure 38: Router initialization messages.............................................................................................................................65
Figure 39: Router initialization messages (Continued) .........................................................................................................66
Figure 40: Removing the dust plug from an SFP slot...........................................................................................................70
Figure 41: Installing an SFP transceiver...............................................................................................................................71
Figure 42: Removing the dust cover from an SFP transceiver .............................................................................................71
Figure 43: Positioning the SFP handle in the upright position ..............................................................................................72
Figure 44: Connecting a fiber optic cable to an SFP transceiver..........................................................................................72
Figure 45: RJ-45 Socket Pin Layout (Front View) ................................................................................................................79
Figures

Figures
8

9
Tables
Table 1: Power LED ............................................................................................................................................................26
Table 2: Fault LED ...............................................................................................................................................................27
Table 3: High Availability LED .............................................................................................................................................28
Table 4: USB LED ...............................................................................................................................................................29
Table 5: SD Card LED .........................................................................................................................................................30
Table 6: LEDs for ETH 1 and ETH 2 Ports (RJ-45) .............................................................................................................31
Table 7: LEDs for the Twisted Pair LAN Ports .....................................................................................................................32
Table 8: LEDs for ETH 1 and ETH 2 ports (SFP) ................................................................................................................33
Table 9: Product Dimensions ...............................................................................................................................................77
Table 10: Product Weights ..................................................................................................................................................77
Table 11: Environmental Specifications ...............................................................................................................................77
Table 12: Maximum Power Consumptions ..........................................................................................................................78
Table 13: Input Voltages ......................................................................................................................................................78
Table 14: Product Certifications ...........................................................................................................................................78
Table 15: Pin Signals for 10 and 100 Mbps .........................................................................................................................79
Table 16: Pin Signals for 1000 Mbps ...................................................................................................................................79
Table 17: RJ-45 Style Serial Console Port Pin Signals .......................................................................................................80

Tables
10

9
Preface
This guide contains the installation instructions for the AT-AR3050S and
AT-AR4050S routers. This preface contains the following sections:
“Document Conventions” on page 10
“Contacting Allied Telesis” on page 11

Preface
10
Document Conventions
This document uses the following conventions:
Note
Notes provide additional information.
Caution
Cautions inform you that performing or omitting a specific action
may result in equipment damage or loss of data.
Warning
Warnings inform you that performing or omitting a specific action
may result in bodily injury.

Installation Guide for AT-AR3050S, AT-AR4050S Routers
11
Contacting Allied Telesis
If you need assistance with this product, you may contact Allied Telesis
technical support by going to the Support & Services section of the Allied
Telesis web site at www.alliedtelesis.com/support. You can find links for
the following services on this page:
24/7 Online Support — Enter our interactive support center to
search for answers to your product questions in our knowledge
database, to check support tickets, to learn about RMAs, and to
contact Allied Telesis technical experts.
USA and EMEA phone support — Select the phone number that
best fits your location and customer type.
Hardware warranty information — Learn about Allied Telesis
warranties and register your product online.
Replacement Services — Submit a Return Merchandise
Authorization (RMA) request via our interactive support center.
Documentation — View the most recent installation and user
guides, software release notes, white papers, and data sheets for
your products.
Software Downloads — Download the latest software releases for
your managed products.
For sales or corporate information, go to www.alliedtelesis.com/
purchase and select your region.

Preface
12

11
Chapter 1
Overview
This chapter contains the following sections:
“Features” on page 12
“Package Contents” on page 14
“Front and Back Panels” on page 15
“Management Panel” on page 17
“Management Software” on page 18
“Twisted Pair Ports” on page 19
“WAN Ports” on page 20
“LEDs” on page 22
“USB Port” on page 31
“USB Retainer Slot” on page 32
“SD Card Slot” on page 35
“Console Port” on page 36
“Reset Button” on page 37
“Power Supply” on page 38

Chapter 1: Overview
12
Features
Here are the features of the AR3050S and AR4050S routers.
10/100/1000
Mbps Twisted
Pair Ports
Here are the basic features of the 10/100/1000 Mbps twisted pair ports.
8 LAN ports per router
10Base-T (IEEE 802.3i), 100Base-TX (IEEE 802.3u), and
1000Base-T (IEEE 802.3ab) compliant
IEEE 802.3u Auto-Negotiation compliant
Auto-MDI/MDIX
100 meters (328 feet) maximum operating distance
RJ-45 connectors
WAN Ports Here are the basic features of the WAN ports.
Supports two ETH ports
Supports two bypass ports
Supports two SFP slots
USB Port Used for maintenance.
USB Retainer
Slot
Used in conjunction with the USB retainer kit
Used for preventing the USB device from falling out the router
SD Card Slot Here are the basic features of the SD card slot.
Used for maintenance
Used for autoboot feature
Supports storage capacity up to 32GB
Reset Button Here are the basic features of the reset button.
Returns to factory default settings
Reboots the router
High Availability Two bypass ports per router
LEDs Here are the LEDs.
Power LED
Fault LED

Installation Guide for AT-AR3050S, AT-AR4050S Routers
13
High Availability LED
USB LED
SD card LED
Duplex/collision and link/activity LEDs for the twisted pair ETH
ports (RJ45)
Duplex/collision and link/activity LEDs for the twisted pair LAN
ports
Link/activity LEDs for the ETH ports (SFP)
Function 1 LED
Function 2 LED
Kensington Lock
Hole
Here are the basic features of the Kensington lock hole.
Used for attaching a lock-and-cable apparatus
One hole located on the center of the back panel
Installation
Options
Here are the installation options for the routers.
Desk or tabletop
19-inch equipment rack - horizontal mounting
Wall mounted
Management
Software and
Interfaces
Here are the management software and interfaces.
AlliedWare Plus™ Operating System
Command line interface
Web browser interface
Management
Methods
Here are the methods for managing the routers.
Local management through the Console port
Remote Telnet and Secure Shell management
Remote web browser management
SNMPv1, v2c, and v3

Chapter 1: Overview
14
Package Contents
1 main unit
1 AC power cable
1 addendum document sheet
1 AC power cord retainer
1 USB retainer
1 double-side adhesive tape
2 cable ties
4 stick-on rubber feet kit
1 RS-232 console cable

Installation Guide for AT-AR3050S, AT-AR4050S Routers
15
Front and Back Panels
The front panel of the AT-AR3050S router is shown in Figure 1.
Figure 1. Front panel of the AT-AR3050S router
The front panel of the AT-AR4050S router is shown in Figure 2.
Figure 2. Front panel of the AT-AR4050S router
CLASS 1
LASER PRODUCT
CONSOLE
SD
SD
FAU LT
PWR
FNC1
FNC2
RESET
1234
56
78 12 BYPASS12
12
USB
HA
FDX HDX COL
READY FAU LT
READY FAU LT
MASTER STANDBY
ETH
ETH
AR3050S
1000 LINK ACT 100 LINK ACT
AR3050S
10/100/1000 Base-T Ports
Intake Air Vents
Management Panel
SFP Slots
ETH Ports
Bypass Ports
CLASS 1
LASER PRODUCT
CONSOLE
SD
SD
FAU LT
PWR
FNC1
FNC2
RESET
1234
56
78 12
BYPASS 12
12
USB
HA
FDX HDX COL
READY FAU LT
READY FAU LT
MASTER STANDBY
ETH
ETH
1000 LINK ACT 100 LINK ACT
AR4050S
10/100/1000 Base-T Ports
Intake Air Vents
Management Panel
SFP Slots
ETH Ports
Bypass Ports

Chapter 1: Overview
16
The back panel of the AT-AR3050S and AT-AR4050S routers is shown in
Figure 3.
Figure 3. Back panel of the AT-AR3050S and AT-AR4050S routers
Power Supply
Power Cable Hook Mount
On/Off switch
Kensington Lock Hole
AC INPUT
100-240V~
50/60Hz
0.9A
FFO
OI NO
Exhaust Air Vents