Allremote Wireless Technology RRC065A User manual

Allremote Wireless Technology, 2006/12/20 1
RRC065A User Manual
1.) Into Duplication Mode:
Make sure “”SW”is on “UP”position.
Press and hold all buttons on RRC065A, blue LED flashing 3 times shortly and 3 seconds
later will light on still, now please releasing buttons. It Had into Duplication Mode now.
2.) Duplicating Code:
2-1. Please be sure RRC065A had in Duplication Mode.
“SW”has to be on “up”position then press any one of
RRC065A button still, Blue LED will keeping flashing.(It
means that in real Duplication situation)
2-2. Releasing all buttons, and please push “SW”to the
down position.
2-3. Please take original remote and press button still also,
close to RRC065A right side to find and searching till
RRC065A red indicator LED indicating more brighter, It
means to the best duplicating position. then press desire button on RRC065A blue LED
will flashing once (It means done), what if blue LED keeping flashing or not light off.(It
means fail), please go back procedure 2-2.
2-4. Push SW1 up.
3.) Finishing Duplicating:
3-1. press all RRC065A together till blue LED flashing once, it means all Done and can be
used.
3-2. What if duplication & set up fail,(Can not remote by RRC065A ),please repeat
procedure 1.) 2.) and 3.) once again.
※Normally press any RRC065A button, it emits including 4 type Frequency (390MHz /
318MHz / 310MHz / 300MHz) Main receiver will operate in 5 seconds, if you need to
re-emitting signal by RRC065A , Please releasing all buttons after blue LED light’s off and
repress once again.
GENIE’S Garage Door operation
1.) Following same way with RRC065A Duplication Mode, Duplicating Genie’s
Remote unit code into RRC065A.
2.) Please Following Genie’s Original User Manual, and learning RRC065A as
new group for setting up.

Allremote Wireless Technology, 2006/12/20 2
4.) Every single Genie’sGarage Main receiver only acceptance 2 pcs RRC065A Maximum to
learn into on each different remote button.
For Example, When you learn into first RRC065A on button A, The second RRC065A
must on button B.
※GENIE’S Main Receiver Learning Mode.
Press once learning button of Main receiver, The LED indicator will keeping
flashing, then press RRC065A face toward to main receiver. When Main
receiver catch the signal the LED is becoming light on still.
Now, Please press once again on RRC065A same button, when main
receiver’s LED indicator is lighted off, It meant Learning is done, be working
immediately on NEW remote unit.
(Note: In certain instances, this procedure may cause the GenieIntellicod /GMI-3BL 
Remote to "unlearn" the programming. Make sure to check the GenieIntellicode /GMI-3BL
Remote when finished, and re-program according to the manufacturer's Instructions if
necessary. Then check both units to make sure that they operate the garage door opener
properly.)
COMPATIBILITY CHART:
REPLACEMENT BRAND Models TRANSMISSION
(APPROX. YEAR) FREQUENCY
Chamberlain 750CB, 753CB,756CB,850CB,853CB,856CB 390 MHz
Genie GIT-1 ,GIT-2,GIT-3,GMI-3BL,GMIC-2BL 390 MHz
GPT90-1,GPT90-3,MAT90,GT912,GCT-3 , GT-31
Lift Master 33LM,51LM,53LM,54LM ,61LM,62LM,63LM,64LM, 390MHz
81LM, 82LM, 83LM, TC-1, TC-2, TC-4.
Sears / Craftsman 1984 ~ 1997 390 MHz
Linear/Moor-O-Matic/ DTC,LB,DT2A,DT4,DT3+1,DTK 310 MHz
Delta 3 system
Digic-code DC5012,DC5032,DC42,DC5062,DC5072 310 MHz
Stanley 1976 ~ 1997 310 MHz
Multi-Code 3060,3070,3083, 3089, 4120,4140 300 MHz
Digic-code 5030,5040,5060,5070 300 MHz

Allremote Wireless Technology, 2006/12/20 3
FCC approved, ID No. OAVRRC065A
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Notice : The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.