Alpha Fan E-Light Pro/56 User manual

Model : E-Light Pro/56
Model : E-Light Pro/40

3
1 - 2
4 - 6
6 - 8
9 - 10
10
10 - 11
11
SAFETY PRECAUTION
Warning
Installation and maintenance work shall only be performed by qualified persons, familiar with local code
and regulation, and experienced with this type of appliance.
All field wiring must be installed in accordance with the national wiring regulation.
Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing
wiring work according to the wiring diagram.
The unit must be GROUNDED to prevent possible hazard due to insulation failure.
The earth wire is approximately 60mm longer than safety wire. This is to ensure at the event whereby
the suspension system fails, the (L) and (N) wire will break leaving the fan remain earthed to prevent
electrocution.
Tighten the blade firmly using a screw driver.
Blades that are detached from the unit during operation will cause serious injuries and property
damages.
The appliances are not intended for use by person (including children) with reduced physical sensory
or mental capabilities or lack of experience and knowledge, unless they have been given supervision or
instruction.
Children should be supervised to ensure that they do not play with the appliances.
Confirm that the power supply has been switched OFF before installing or servicing the unit. Ensure
that the blade is fully static before doing any maintenance work.

SAFETY PRECAUTION
Disconnect from the main power supply before servicing the unit.
DO NOT pull out the power cord when the power is ON. This may cause serious electrical shocks
which may result in fire hazards.
STOP using the ceiling fan when any abnormality or failure occurs.
Immediately stop using the ceiling fan and switch off the power supply. Please contact you authorized
dealer for repairing and maintenance work.
CAUTION
Please take note of the following important points when installing.
Safety cord should not be longer than the earthing conductor.
Should failure of the suspension system occur, the supporting of the fan must not rely on the earthing
conductor. The earthing terminal in the fan assembly should be such that should any part of the
suspension system fall off, the body of the fan assembly shall effectively earthed.
Ensure that the unit’s panel is closed after service or installation.
Unsecured panels will cause the unit to operate noisily.
Sharp edges and coil surfaces are potential locations which may cause injury hazards. Avoid
from being in contact with these places.
Before turning off the power supply set the remote controller’s ON/OFF switch to the “OFF”
position.
If this is not done, the unit’s fans will start turning automatically when power resumes, posing a hazard
to service personnel or the user.
Do not operate any heating apparatus too close to the ceiling fan unit or use in room where mineral oil,
oil vapour or oil steam exist, this may cause plastic part to melt or deform as a result of excessive heat
or chemical reaction.
Ensure the colour of wires of the outdoor unit and the terminal markings are same to the indoors
respectively.
Don’t use joined and twisted wires for incoming power supply.
Do not place any object in the path of the blades. Avoid raising objects or your arms near the ceiling
fan.
The installation instruction shall include the recommendation that the fan suspension system shall
be examined regularly, at least once in every two years. This recommendation shall be written on the
fan and on the regulator or permanently attached to the fan and to the regulator and be visible to user.
The writing shall be legible and permanent.
2

3
10.
Transmitter & Holder x 1
AAA
AAA
Battery x 2
TIMER ON
Bolt x 2

4
Yellow/Green (E)

5

6
AAA
AAA
1. Insert the 2 pcs of AAA battery (provided) into the transmitter.
2. Mount the transmitter holder on the wall with the screws provided.

1h - Fan turns on after 1 hour
3h - Fan turns on after 3 hours
6h - Fan turns on after 6 hours
8h - Fan turns on after 8 hours
Timer On
Light
Light control
7
TIMER ON
Natural Wind
Fan speed changes within
its range creating gentle
sea-breeze effect
Forward Reverse
Anti-clockwise or
clockwise rotation
TRANSMITTER LEARNING PROCESS
AAA
AAA
DO NOT PRESS ANY OTHER BUTTON ON THE TRANSMITTER DURING THIS PROCEDURE.
a) Turn on the power supply (wall switch) to the fan.
b) Within 30 sec, use a test pen to press and hold the “LEARN” button for 3 sec. Once the receiver has
detected and learned the frequency, the light on fan will be lighted and fan will be working at low speed
and process is completed and fan is ready to use.
The receiver & transmitter is pre-programmed in factory. If you wish to control 2 or more fans using
1 transmitter, the below steps is required.
Press and hold for 3 sec
Learn
Power
Turn off fan

Last Memory Function
The transmitter & receiver is incorporated with last memory function. It stores the last reading/setting on
memory and when the fan is switch on again, the operation will be as the last memory/setting.
The Emergency Light is equipped with rechargable lithium battery.
For initial use :
- turn on the power switch to charge the battery for 15hrs.
user may use the transmitter to turn off the fan speed and light during charging.
During power failure :
- emergency light will turn on automatically.
- emergency light standby time up to 6 hours (if battery power is full).
- to turn off the emergency light, press the LIGHT button on the transmitter.
Charging of battery
- automactically charge when there is power supply.
- a red light will blink from the emergency light when the battery power is low.
- recharging time is between 2hrs - 15hrs.
EMERGENCY LIGHT USER GUIDE
8

9