ALPHA LITE A8-PLUS-J User manual

BASE SOFT LIGHT A8-PLUS-J
USER MANUAL
December. 2019

Safety Information
1. Do not open or disassemble the cover to reduce the risk of electric shock.
2. Please wear safety equipment such as safety helmet during work.
3. Be sure to fix the safety chain on the product when installing and moving.
4. Please install the signs below for people to bypass
when install the product on high truss.
5. The work should be done under the direction of approved specialist
who is trained in safety and mechanical installations.
WARNING
- 2 -

Contents
Safety Information
2
Contents
3
[Fixture Information]
Fixture Information
4
Fixture Exterior View
5
Dimensions
6
Technical Specifications
7
[Fixture Installation]
Barn Door Assembly
8
Diffuser Lens Change
9
Power Connection
10
DMX Connection
11
[LCD Screen Instructions]
Unlocking
12
Screen Instructions
13
Menu Tree
14
[Setting]
Product Information
15
DMX Mode Channel Change
16
(DMX Mode)
Address Setup
16
User Mode Setup
17
(User Mode)
Intensity / CCT / Tint Adjust
17
Color Mode Setup
18
(Color Mode)
RGB / Saturation / Intensity Adjust
18
Sleep Mode Function
19
Master Function
19
RDM On/Off Setup
19
Dimming Speed Setup
19
Fixture ID Setup
20
(RDM)
Fixture Label Setup
20
[Error Information]
Temperature Sensor
21
Network Connection
21
[Function Information]
Cross Fader
22
Color Macro
22
[Protocols]
DMX Protocols
23
RDM Protocols
26
- 3 -

Fixture Information
A-Plus Series is a flat light source lighting fixture mainly used in
broadcasting studios, and it is excellent in diffusivity, low in glare and
not exposed to elements.
A-Plus Series is possible to express 2,500~10,000K color temperature
and full color by combining LED which can control color temperature
and RGB LED, so it is used to create various sets of atmosphere.
A-Plus Series that uses high efficiency CRI LED light sources
can increase lifetime and reduce maintenance cost and power
consumption.
- 4 -

Fixture Exterior View
Stirrup Smart Touch
LCD Screen
Handle
Fixed Knob
- 5 -
Barn Door
Connector
Panel
Clamp

mm
(inch)
Dimensions (A8-Plus)
- 6 -

Technical Specifications
- 7 -
A8-Plus
Physical Size
792 x 441 x 204mm
Beam Angle
135°
Body + Lens Weight (kg/lbs)
13.5 / 29.8
Handling
Adjusting Sliding Stirrup, High Strength Tilt Lock
Mounting
16mm / 28mm
Tilt Angle
±270°
Power Supply Range
AC 100-240V, 50/60Hz
Power Consumption
400W
White Light (CCT)
Full 2,500~10,000K (VCT)
Colored Light
Full RGB+W (4 Color gamut with Hue and Saturation control)
CRI
95~98
Dimming
0~100% 16-bit
Control
5-PIN DMX In and Out, Smart Touch LCD Controller, RDM,
(Option) Wireless DMX512, Wireless RDM
Remote Device Management
Supported
Ambient Temperature Operation
-20~45°C
IP Rating
IP20
Estimated LED Lifetime
Over 50,000 hours

Barn Door Assembly
①Fit the bottom of
the barn door into
the groove on the
top of the body.
②Slide the barn door
along the groove.
③Fit the bolt on the
upper barn door
to the groove.
④Turn the bolt clockwise
to fix it.
- 8 -

Diffuser Lens Change
①Pull back the latches across
the diffuser lens.
②Pull out the diffuser lens to
the left.
- 9 -
※ When replacing the diffuser lens,
insert it with the smooth side facing inward.
(Rough side facing forward)

1. Observe the proper voltage range
2. If power is supplied outside the range, noise may be generated from the SMPS.
3. If the operating voltage is out of the proper voltage range,
SMPS function may be degraded or damaged.
Power Connection
AC power at 100-240V, 50-60Hz
- 10 -
1. USB PORT (for ADMINISTRATOR ONLY)
2. POWER OUT
3. POWER IN
4. DMX OUT
5. DMX IN
6. POWER ON/OFF SWITCH
(Do not connect USB
without administrator's permission.)
1 2 3 4 5 6