Alphatech Alpha Guard TC35 User manual

- 1 -
The Basic features:
Alpha Guard has been designed especiallyfor:
o Protection ofproperties and cars
o Remote data collection
o Remote control ofel. devices
o Alarm
o Remote signalization
The Basic technical parametres:
GSM module TC35 or MC35 900/1800 MHz
Power supply9 to 15V ss
4programmable ports ofprocessor (inputs/outputs, pulses, etc. Up used
software) 5V/10mA
serial input and output ofGSM modemwith 3V level
voice input and output cca 100mV
restart ofGSM module
at connector is possible connect optional modules (voice module,
monitoring (overhear) module, relaymodule etc.)
transmit DTMF tones after connecting
detection oftones after connecting (busytone, ringing tone etc.)
Real time clock
Timer (alarm)
The type of application is limited bysoftware in
processor:
o GSMinvoker :inputs are not used. During ringing from„list of
permitted numbers“ stored on SIM card you makean alarm.Then are
progressivelycalling “invoking numbers“ stored on SIM card – invoking
call is free charge (Suitable for example: fire department).
o Alarm-Guard mode :device is equipped by4inputs (states) – for each
you can programm ownSMS with telephone number. In case ofstate
changing is sent corresponding SMS to preprogrammed number.
Simoultenously(up setting) call (ringing – warning free charge) up 8
preprogrammed numbers. When you connect optional modules you can
monitor guarded area.
o Remote control mode:2inputs in Guard mode and 2outputs can be
used for connection different types of devices (relayfor switching). It can
be used for monitoring as well.

- 2 -
o Remote data collection – the integrated processor can scanning for
example: pulses fromdifferent measurements and send measured
values backon line.
We can prepare O E M optional modules up your needs!!!!

- 3 -
Alpha Guard type 4in/A
Guarding device is equipped by4inputs (states) – for each you can set
ownSMS with telephone number. In case ofstate changing (short circuit
ofinputs against ground for timelonger than 1sec.) the device send
corresponding SMS to preprogrammed number. Simultaneously(up
setting) call (ringing – warning is free charge) up 8preprogrammed
numbers. When call has been picked up you hear interrupted alarmtone.
InstalIation
Unmarkpins are used in other applications ofAlpha Guard (RX, TX, nf
input, nfoutput, IGNITION etc.)
Power supply9 to 15V
over DC conector
Antenna conector
Input 1 (pin 11)
Input 2 (pin 12)
Input 3 (pin 13)
Input 4 (pin 14)
+5V (pin 6 and 7)
for optional device
ground (pin 8 and 9)
Input offeeding
+9 to +15V or
ACU (pin 5)

- 4 -
Power supply
Regard to connectors
connection in the device (via
picture) you can power supply
provide bymore ways:
· The simplest wayis feeding
fromordinaryss adapter 9
to 12V (+ in the middle),
which is plug into DC
connector.
· The same ways you can use
feeding fromUPS. (then is
alreadyconnected ground
for each inputs).
· The similiar is using pin 5 (and ground pin 8 and 9) for connection
feeding fromUPS exchange – then is used for connection ofinputs as
same as feeding the connector 1 only.
Connection ofinputs
The inputs 3 and 4 is possible used either for connection ofdevices with 5V
logic or for direct connection with various switching contacts (optron,
transistor). The inputs 1 and 2 is possible used for connection ofdevices
with 5V logic. In case ofswitching contacts using is neccessaryto connect
among input and +5V resistor of10 Kohm.

- 5 -
Example ofpractise using for guarding oflevel height.
Preparation ofSIM card
On the SIM card are stored all numbers and SMS messages, which are
using bydevice. The alarmnumbers where are device calling (during
states changing) are stored under name MASTER 1 to MASTER 8.The
numbers where SMS has been sent are stored together with messages.
· Insert SIM card to mobile phone.
· Set starting without PIN.
· To phone bookstore numbers MASTER1… (called in case of
alarm). The numeral after name MASTER makes order ofcalled
number. Store howmanyMASTERx numbers howmanyyou need
only. (Example MASTER 1 only).When you do not want use this
feature – store nothing.
· When you have alreadysome SMS on the SIM card – erase them.
· Store on the SIM required SMS with corresponding phone numbers
where will be sent. (Alarmofeach input can be sent to another
telephone number !). The messages store in order ofeach inputs
(first message for input 1 then for 2 etc.). When phone not enables
to message store a number (NOKIA phones) then is send special
SMS „Failure at input x“ to number MASTER1.
· Turn off the phone and take awaythe SIM card

- 6 -
Installation
· Insert the SIM card.(After
pressing yellowbutton the
SIM card reader will move
out).
· Connect antenna.
· Connect inputs (use
enclosed cabel with
connector (via follow
picture)
· Connect power supply.
· Light up green LED at the
front cover
· 3 times shortlyflash red LED at the front cover and starts flashing
in 2 sec. period.
· The red LED flashing quickly – log into GSM network.
· The red LED flashing in 2 sec. period again – stand bymode,
device is readyfor operation.
· Make an Alarm: the red LED start flashing quickly(calling to
preprogrammed numbers, sending SMS). Progressivelyringing at
numbers stored as MASTERx (when call is not pickup or refuse
then device calling to next number). At phone with corresponding
number is send SMS message.
· Call fromanyMASTER phone to the device: Your call will be after
1 ring refused. The device will send at this phone SMS message
with states ofeach inputs.
· Call fromanyphone to the device which is not MASTER.Your call
will be ignorated.

- 7 -
The most often problems during installation
It is not lighting anyLED.
Problemin feeding. Checkfeeding connection.
The speed red „log in network„ LED flashing has not performed
The module has not log into the GSM network:
· wrong SIM card (or bad insert to reader)
· old 5V SIM card (the module supports cards 3V and less)
· set log into GSM networkwith PIN
· so much bad GSM signal
Nothing hapened during alarm:
At the SIM card are not stored numbers called MASTER and SMS
messages.
The inputs 1 and 2 are used with contact without resistor at +5V .

- 8 -
Cabel with connector
input 1 pink
input 2 Light green
input 3 Black and
white
input 4 Brown and
white
Input offeeding +9 to
+15V yellow
ground Purple+grey