Alphawave AWCL-300-6P-Audio-DMX User manual

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 1
V.201103A3
AWCL-300-6P-Audio-DMX
DMX 30 channels audio
synchronized Console
USER’S MANUAL

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 2
V.201103A3
1. Introduction:
1.1 Features
Standard DMX-512A protocol support。
The DMX-512A protocol is included with the voice assage operation that could be
set as a voice eter。
AWCL-300-6P-Audio-DMX could connect and control RGB LED lighting directly,
without any DMX decoder for support。
Support IR-re ote control interface。
R、G、B brightness can be adjusted individually as the di er function, and auto-save
the setting。
Built-in six LED dyna ic progra s; dyna ic ode can be set Fade/Ju p and changed
the dyna ic speed.
Real Audio Synchronized color LED Control.
When there is no any voice, the Audio Synchronized odes will switch to the Silent
color fade ode auto atically.
Adjustable Sensitivity for audio synchronized ode (including Microphone and Line-in
sources ode).
 Audio source option of Line-in or Microphone .
 The axi u output is 4A x 3 channels, that is 150W/12V or 300W/24V。
1.2 Specifications
Operation Voltage DC10V~30V。
LED Output Power 150W/12V or 300W/24V
LED Module Type Constant Voltage with constant current or
Constant voltage with li it voltage.
Max output Signal Channel 30 channels / 3 channel(RGB)=10 decoders
Max output LED current 4A/channel x 3 channel
Weight 250g
Size L:110 xW:70 xH:23
Operation Te perature 0°C ~+70 °C
Storage Te perature -20°C ~ +85 °C

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 3
V.201103A3
2.User Guide
2.1 Input/output interface
<Upper Front Side>
Vled : The connector of LED’s power supply (DC 10V~30V is based on the LED
Module connected to the controller)。
“ ━
━━
━ “ : Ground of power supply。
B : The connector of the Blue LED 。（cathode of Blue LED odule）
G : The connector of the Green LED 。（cathode of Green LED odule）
R : The connector of the Red LED 。（cathode of Red LED odule）
Mic. : The icrophone。
DMX : DMX signal output port, for connecting the DMX decoder.
**DMX signal output port:
Blue line: GND
Green line: D1-
Red line: D1+
hite line: No function.

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 4
V.201103A3
IR Receiver : The Receiver of IR Re ote Controller。
Extension IR Receiver ire: The 50c long extension wire of IR Receiver could be pull
out for using or storage in the case easily.
<Front Side>
Vled : The connector of LED’s power supply (DC 10V~30V is based on the LED
Module connected to the controller)。
B : The connector of the Blue LED 。（cathode of Blue LED odule）
G : The connector of the Green LED 。（cathode of Green LED odule）
R : The connector of the Red LED。（cathode of Red LED odule）
“ ” : Silence ode (one of sound control ode switch)
“ ” : Audio-in ode (one of sound control ode switch)
“ ” : Microphone-in ode (one of sound control ode switch)

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 5
V.201103A3
<Left Side>
Vled : The connector of LED’s power supply (DC 10V~30V is based on the LED
Module connected to the controller)。
“ ━
━━
━ “ : Ground of power supply。
DC-In : Power input。 (Connected with Vled and support DC 12V/24V input)。
“S” : Sensitive control of sound source (Included with the “Audio-in” and
“Microphone-in” ode)
Increasing the sensitive control: Turn to left side.
Decrease the sensitive control: Turn to right side.
Line-In : Audio Line-in connector. Before Audio line-in, please tune the voice down;
after Audio line-in, and then tune the voice loud.

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 6
V.201103A3
2.2Application
A. Connect A CL-300-6P-Audio-DMX to LED lightings directly.
**The best benefit: the DMX console may directly connect and control the RGB
LED lightings without DMX decoder
Output power: DC12V/180W; DC24V/360W
B. Connect A CL-300-6P-Audio-DMX with an Audio player for sound control.
Please connect the Audio player with an Audio A plifier and with an
AWCL-300-6P-Audio-DMX by AV ter inal shunt.
Therefore, it will be easy to control the audio a plifier’s volu e and won’t influence
the Line-in signal of AWCL-300-6P-Audio-DMX at the sa e ti e.
Please have below application chart for your reference:

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 7
V.201103A3
C. Connect A CL-300-6P-Audio-DMX with the DMX Decoder (HERMES:
A CL-120-DMX-D3C) for DMX system control.
Could be set as a DMX-512 aster (the DMX Console)-slave (The decoder) ode.
AWCL-300-6P-Adusio-DMX could control at ost 9 sets decoder at the sa e ti e.
Below is the application chart:

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 8
V.201103A3
To let the DMX control syste run the built-in progra s perfectly, please set these DMX
decoders’ address in turn as follows:
You ay use the IR re ote controller to choose the built-in progra based on above DMX
decoders’ address setting, below is the order changing of DMX decoders:
(When these progra s running, it is the sa e way to set the Fade/Ju p or speed changing
function)
1. When setting progra no. P1/P2/P3:

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 9
V.201103A3
2. When setting progra no. P4/P5/P6:
2.3IR Remote Controller
Power Power ON/OFF
R, G, B, O, Y, I, W, P
Single color in static ode
( =100% Red; =100% Green; =100% Blue;

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 10
V.201103A3
Orange=100%Red+50% Green;
Yellow=100%Red+100%Green;
Indigo=100%Green+100%Blue;
White=100%Red+100%Green+100%Blue;
Purple=100%Red+100%Blue.)
E Voice control function
Speed+ /- P1~P6 Dyna ic ode speeding or slower, total 25 degrees.
※
Brightness+/-
Dyna ic ode and static ode brighter or darker, total 16
degrees. ※※
**When in “Voice control ode”, you ay use the “brightness”
control the Sensitive of sound source. Darker eans to reduce
the sensitive, but it won’t be auto-save in the setting.
Pause
P1~P6 pause. Press the “Pause” button again after set in pause
ode, it will back to the ode before you pause it.
Fade/Ju p Switching P1~P6 to Fade/Ju p ode
P1~P6 progra s Built-in Color ixing 6 progra s.
Choose one progra then set it in fade or ju p ode.
P1
100%Red ->100%Red+100%Green ->100%Green
->100%Green+100%Blue ->100%Blue ->100%Red+100%Blue
->100%Red->repeat
P2
100%Red ->100%Red+50%Green ->100%Red+100%Green
->50%Red+100%Green ->100%Green ->100%Green+50%Blue
->100%Green+100%Blue ->50%Green+100%Blue ->100%Blue
->50%Red+100%Blue ->100%Red+100%Blue
->100%Red+50%Blue ->100% Red ->repeat
P3
100%Red ->100%Green ->100%Blue ->100%Green ->100%Red
->repeat

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 11
V.201103A3
P4
100%Red ->Dark ->100%Red+100%Green ->Dark ->100%Green
->Dark ->100%Green+100%Blue ->Dark ->100%Blue ->Dark
->100%Red+100%Blue ->Dark ->100%Red ->Dark ->repeat
P5
100%Red ->100%Red+100%Green ->100%Green
->100%Green+100%Blue ->100%Red+100%Green+100%Blue
->100%Blue ->Dark ->100%Red+100%Blue ->100%Red->repeat
P6
100%Red+100%Green ->Dark ->100%Green+100%Blue ->Dark
->100%Red+100%Blue ->Dark ->repeat
R+/- Add or decrease red color in static ode, total 16 degrees.
※※
G+/-
Add or decrease green color in static ode, total 16 degrees. ※
※
B+/- Add or decrease blue color in static ode, total 16 degrees.
※※
※：The speeding degrees as follows :（second）
1 2 3 4 5 6 7 8 9 10 11 12 13
0.064 0.128 0.256 0.512 0.768 1.024 1.536 2.048 3.072 4.096 5.12 7.168 8.192
14 115 16 17 18 19 20 21 22 23 24 25
10.24 12.288
15.36 20.48 32.768
40.96 49.152
65.536
81.92 102.4 147.46
204.8
※※：The brightness degrees as follows : (%)
1 2 3 4 5 6 7 8 9
0 6.25 12.5 18.7 25 31.25 37.5 43.74 50
10 11 12 13 14 15 16 17
56.25 62.5 68.75 75 81.25 87.5 93.75 100
Note:
1. R+-/G+-/B+-:To ix the color you need to be in static ode. For exa ple, while the color
of the LED odule is blue, press R+ button, then the LED color turn to purple; press R-
button again, the LED color will return to blue.
2. P1~P6 color ixing progra s: Built-in color ixing progra s could not be changed. When
ass quantity, user could have their own design of color ixing progra s.

AWCL-300-6P-Audio-DMX DMX Console
2010
Page 12
V.201103A3
2.4 Appendix
For reference: you ay use these wires for AWCL-300-6P-Audio-DMX to arrange “Audio
Line-in”