Alpine PDX-M6 User manual

All manuals and user guides at all-guides.com

<Cautions for Safe Repair Work>
The following cautions will prevent accidents in the workplace and will ensure safe products.
*The symbols indicate caution is needed to prevent injuries and damage to property.
The symbols and their meanings follow.
If you ignore this symbol and handle the product incorrectly or unsafely,
serious injury or death may result.
If you ignore this symbol and handle the product incorrectly or unsafely,
injury or only material damage may result.
*The following symbols indicate two levels of cautions.
When you see this symbol, you have to be very careful.
When you see this symbol, you have to follow the instructions there.
Do not look squarely into the laser light Fuse Caution
coming from the pickup.
A
lways use a designated fuse.
You may loose you sight.
Use of an incorrect fuse may result in a fire.
Do not allow wiring to be caught in the Battery Caution
screw/chassis. Use the designated battery.
If wiring is caught in the screw/chassis, it may Confirm the correct polarity and seat of the
cause a short circuit, resulting in a fire. battery.
A
n incorrect battery or an improperly connected
or seated battery may result in a fire.
High Temperature Caution Designated Parts Caution
Touching the heat sink may cause severe burns. Look up the part list and ensure that only
designated parts are used to prevent problems o
r
accidents.
Reverse Power Supply Connections or Wiring Caution
Misconnections Caution Ensure that the wiring is correct when rewiring to
Reverse power supply connections o
r
prevent problems with ignition/breakdown.
misconnections may cause ignition problems and
smoke may result.
Soldering Caution Wear Gloves
Hot solder from solder splash may cause severe Wear gloves to prevent electrical shocks or injury
burns.
from the end face of the metal.
Warning
Caution
Warning
Caution
All manuals and user guides at all-guides.com

X4
X4
X4
X2
Packing Method View
110
109
108
107
106
105
104
103
102101
All manuals and user guides at all-guides.com

#1 101 68-13530Z47 MANUAL,OWNER'S(AO),(GO)
$1 101 68-13530Z47 MANUAL,OWNER'S(AO),(GO)
%1 101 68-13530Z47 MANUAL,OWNER'S(AO),(GO)
&1 101 68-16909Z18 MANUAL,OWNER'S(AOCHR)
$1 102 68-13530Z48 MANUAL,OWNER'S(I,G,S)
103 09E41475S01 CONN,P-PLUG
104 09E41474S01 CONN,SPK-PLUG
105 43E41458S01 SPACER,STACKING
106 03E36691S01 WRENCH,2X2.3
107 47E35195S01 WRENCH,4X4.6
108 03E41468S01 SCR,M3X7(B)(BLK)
109 03E41470S01 SCR,M4X24(HW)(BLK)
110 03E41472S01 SCR,M4X36(HW)(BLK)
All manuals and user guides at all-guides.com

Mark Model Code
#1 PDX-M6(North American) Only,
$1 PDX-M6(European) Only,
%1 PDX-M6(General Foreign) Only,
&1 PDX-M6(Chinese) Only,
Others:Common.
NOTE:The part that has not PART NUMBER will not be supplied.
#####
All manuals and user guides at all-guides.com

CH6551
CB8001
CH6501
(1)
(2)
MAIN-P.W.Board
SUB-P.W.Board
LED-P.W.Board
(1) 01E39992S01
(2) No Extension Cord needed.
Extension Cable *Always connect the Extension Cable when making checks of voltage and repair.
All manuals and user guides at all-guides.com

Specifications
Power Output
(
1
)
20Hz, 4ohm, 1.0% T.H.D.
(
14.4V
)
600W
100Hz, 4ohm, 1.0% T.H.D.
(
14.4V
)
600W
(
2
)
20Hz, 2ohm, 1.0% T.H.D.
(
14.4V
)
600W
100Hz, 2ohm, 1.0% T.H.D.
(
14.4V
)
600W
T.H.D.
(
100Hz, 200W/ 4ohm
(
14.4V
))
0.1%
Residual Noise
(
Input Short, Non-Filter
)
5.0mV
S/N Ratio
(
Input Short
)
(
1
)
Ref.Output 1W/ 4ohm, CEA-2006 78dB
(
2
)
Ref.Output 600W/ 4ohm 106dB
Frequenc
y
Response
(
Ref.Output 1W/ 4ohm, Ref.Frequenc
y
50Hz
)
10Hz : -0.5±2dB
400Hz : -3.0±2dB
Output Offset Volta
g
e
(
No Si
g
nal
)
±150mV
Input Sensitivit
y
(
Ref.Output 600W/ 4ohm, 100Hz
)
(
Volume Position : MAX
)
Input Level Switch Position : 0.1Vrms~1.0Vrms 0.125V±3dB
Input Level Switch Position : 1.0Vrms~8.0Vrms 1.0V±3dB
SUB-SONIC Filter
(
Ref.Output 1W/ 4ohm, 50Hz at SUB-SONIC Filter Switch: OFF
)
SUB-SONIC Filter Switch Position : 15Hz -3.0±2dB
SUB-SONIC Filter Switch Position : 30Hz -3.0±2dB
Low Pass Filter
(
Ref.Output 1W/ 4ohm, 50Hz at Low Pass Filter Volume: MAX
(
400Hz
))
-3.0±2dB
Pre-Out Level at 1.0Vrms Input CH1 : 1.0Vrms±3dB
CH2 : 1.0Vrms±3dB
Remote On Volta
g
e 6.4±1.0V
Current Drain
(
1
)
No Si
g
nal 2.1A
(
2
)
1% T.H.D., 2ohm Load 80A
(
3
)
Remote Current Drain 0.33±0.2mA
(
4
)
Back Up Current Drain 1.2mA
Input Impedance
(
Reference
)
20.40Kohm±10%
Fuse Requirement 20A
(
Peak
)
x 4
(
For Batter
y
Line
)
Power Source DC14.4V
(
11~16V
)
Dimensions
(
W x H x D
)
257 x 50.8 x 192mm
Wei
g
ht 2.82k
g
NOTE : Due to Continuin
g
product improvement, specifications and desi
g
ns are sub
j
ect to chan
g
e without notice.
All manuals and user guides at all-guides.com

x2pcs
uCOM Block
uCOM +5V
uCOM
for Variable Load
Vss+12V
Vss+12V
V-DET
Trans Temp.
Trans
Trans
Thermal Protect
Thermal Detect
Thermal Detect
Thermal Detect
Thermal Adjustable Limiter
Terminal
TOSHIBA
TMP87C847U
Subsonic
Sub-
Speaker Output
Sonic
SP8K31
S/W
Reset
Remote+B
Remote Bass
RCA Input
RCA Input
Protection
Protect Control
Power Supply Block
Power Supply
Power Control
Power
Power
PWM Driver
PWM Control/FET Driver
PWM Control/FET Driver
PWM Control
PWM Control
PWM
POWER_2
POWER_1
Over Current
Operation
OFF
NJU7222U50
NCV494BD
NCV494BD
Modulator
Mix Gain
MOS FET
MOS FET
MOS FET
MOS FET
MOS FET
MONO 1
MONO 1
MONO
MOD NFB
MOD NFB
Limiter LPF
LM5109Bx2pcs
LED Control
LED Block
LED
LED
LC Filter
LC Filter
Isolator
Isolator
Inverted
Internal Temp.
Input Input
Input Input
IRFP4004 2para
IRFP4004 2para
IRFB5615 1para
IRFB5615 1para
Gain Vol
FET
Digital Amplifier Block
Detect
Detect
D_AMP_STB
Current Limiter
Control
Buffer
Buffer
Buffer
Block Diagram
Battery Detect Limiter
BTL
BLUE/RED
BD5243G
BD5240G
BAJ2CC0FP
BAJ2CC0FP
B-DET
Attenuate
Anaview’s technology
Analog Block
Analog -15V
Analog +15V
2700uF/63Vx2para
2700uF/63Vx2para
98-1036TRPbF
98-1036TRPbF
30Hz
18T:32T:30T
15Hz
5T:9T:9T
2nd Voltage
2nd Capacitor
2nd Capacitor
-Vss
-6dB
+Vcc
+B
+B
+12V
+/-15V
(discrete)
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com