Alpine NVD-W912 User manual

QUICK REFERENCE GUIDE
IN-DASH GPS NAVIGATION RECEIVER
Map Update applies to following products:
NVD-W912 for INA-W910 and IVA-NAV-20
NVD-W902 for INA-W900, INA-W900BT and
IVA-NAV-10
INA-W900, INA-W900BT & IVA-NAV-10 do not have the Traffic Feature

TABLE OF CONTENTS
SYSTEM CONTROLS........................................................... 2
LANE GUIDANCE.................................................................. 3
JUNCTION VIEW................................................................... 3
ENTERING AN ADDRESS.................................................. 4
SELECT AN INTERSECTION
AS THE DESTINATION ....................................................... 7
QUICK SEARCH FOR A PLACE OF INTEREST......... 10
EDITING THE LIST OF DESTINATIONS ..................... 12
CANCEL THE ACTIVE ROUTE........................................ 13
SAVING A LOCATION AS AN
ADDRESS BOOK ENTRY.................................................. 14
SPEED LIMIT WARNING ................................................. 15
ADJUSTING SPEED WARNING..................................... 16
TRAFFIC SETTINGS /
UNDERSTANDING TRAFFIC........................................... 17
TRAFFIC INFORMATION IN ROUTE PLANNING .......................... 17
REAL-TIME TRAFFIC INFORMATION (TMC) ............................... 17
TRAFFIC EVENTS ............................................................... 19
TO ENABLE/DISABLE TRAFFIC FEATURES.............. 20
QUICK MENU ....................................................................... 21
ROUTE SETTINGS.............................................................. 22
SELECTED MAP LOCATION (CURSOR) AND SELECTED
MAP OBJECT.............................................................................. 23
SCROLLING THE MAP ..................................................... 24
CHANGING THE LANGUAGE.......................................... 26
WHAT’S NEW? .................................................................... 28
FAQ .......................................................................................... 30

2
SYSTEM CONTROLS

3
LANE GUIDANCE
When navigating, these arrows
represent the lanes to take.
JUNCTION VIEW
When navigating, highlighted
signs represent which lanes to
use; all others are dimmed.

4
ENTERING AN ADDRESS
To enter an address as the
destination, do as follows:
1. Press the [NAVI MENU],
then tap
2. Tap
3. By default, the software
proposes the state where
you are driving. If needed,
tap , enter a few
letters of the destination
state on the keyboard, and
select one from the list.
4. Select a new city:
a. Tap . The city of your
current location is offered
by default. For a local
search, tap to accept it,
otherwise continue with
entering the destination
city name.
b. Start entering the
name of the city on the
keyboard.

5
c. Find the city you need:
• The most likely city
name is always shown
in the input field. To
accept it, tap .
• If the desired name
does not appear, a
list a names will open
representing the names
that are the closest
match to the characters
you have entered. To
open this list before
completing your entry,
tap , then select
the city from the list.
5. Enter the street name:
a. Start entering the street
name on the keyboard.
b. Find the street you need:
• The most likely street
name is always shown
in the input field. To
accept it, tap .
• If the desired name
does not appear, a
list a names will open
representing the names
that are the closest
match to the characters
you have entered. To
open this list before
completing your entry,
tap , then select
the street from the list.
ENTERING AN ADDRESS

6
ENTERING AN ADDRESS
6. Enter the house number:
a. Enter the house number
on the keyboard. (To
enter symbols, tap ).
b. Tap
to finish entering the
address. (if the entered
house number cannot be
found, the midpoint of the
street is selected as the
destination.)
7. A full screen map appears
with the selected point in
the middle. If necessary, tap
the map somewhere else
to modify the destination.
The Cursor ( ) appears
at the new location. Tap
to confirm
the destination, or tap
to select a different
destination.
8. After a short summary of
the route parameters, the
map appears showing the
entire route. The route is
automatically calculated.
Tap to modify
route parameters, or tap
and
start your journey.

7
To enter an intersection of two
streets as the destination, do
as follows:
1. Press the [NAVI MENU]
hard key, then tap
2. Tap .
3. By default, the software
proposes the state where
you are. If needed, tap
, enter a few
letters of the destination
state on the keyboard, and
select one from the list.
4. Select a new city:
a. Tap . The city of your
current location is offered
by default. For a local
search, tap to accept it,
otherwise continue with
entering the destination
city name.
b. Start entering the
name of the city on the
keyboard.
SELECT AN INTERSECTION AS THE DESTINATION

8
c. Find the city you need:
• The most likely city
name is always shown
in the input field. To
accept it, tap .
• If the desired name
does not appear, a
list a names will open
representing the names
that are the closest
match to the characters
you have entered. To
open this list before
completing your entry,
tap , then select
the city from the list.
5. Enter the street name:
a. Start entering the street
name on the keyboard.
b. Find the street you need:
• The most likely street
name is always shown
in the input field. To
accept it, tap .
• If the desired name
does not appear, a
list a names will open
representing the names
that are the closest
match to the characters
you have entered. To
open this list before
completing your entry,
tap . Then select
the street from the list.
SELECT AN INTERSECTION AS THE DESTINATION

9
6. Instead of entering the
house number, tap
. The system
will prompt you to enter the
intersecting street name.
7. A full screen map appears
with the selected point in
the middle. If necessary, tap
the map somewhere else
to modify the destination.
The Cursor ( ) appears
at the new location. Tap
to confirm
the destination, or tap
to select a different
destination.
8. After a short summary of
the route parameters, the
map appears showing the
entire route. The route is
automatically calculated.
Tap to modify
route parameters, or tap
and
start your journey.
SELECT AN INTERSECTION AS THE DESTINATION