Alpine INE-W611D Technical manual

Map-Update
INE-W611D(C)
Map Update Process for
INE-W611D / INE-W611DC / INE-W611DU
English
Sep 2021, Version 1.1

Instructions for updating the map data for
INE-W611D / INE-W611DC:
Please register at alpine.naviextras.com. Download the "Toolbox" from the download area before
following the Map Update instructions for your Alpine navigation device.
Naviextras Toolbox
Alpine.naviextras.com is the official map update portal for Alpine.
Some alpine.naviextras.com site features, including buying updates, require that your Alpine
navigation device is registered.
Please register your Alpine navigation device and your required personal data within Naviextras
Toolbox, which is a free PC-tool.
alpine.naviextras.com
Requirements and limitations:
•Windows XP / Windows 7 / Windows 8 / Windows 10
•Software for unpacking ZIP files
•USB stick with minimum 16 GB recommended (freshly FAT32 formatted)
Do not delete any files / folders from the USB stick and do
not add any files / folders manually.
Note:
The map update process may consist of two parts - depending on the pre-installed navigation
firmware on your navigation device. For more information, see the update instructions.

Map Update Process
1) Connect an empty USB stick (freshly FAT32 formatted) to the navigation system.
2) Go to Navigation →Main Menu → scroll to right →Update. Press the soft key “Update”.
3) The Update tool starts up.
4) Confirm with soft key “Yes”.

5) Device information transferred to the USB stick.
Do not disconnect the USB stick and do not power off the unit.
6) Confirm with “OK”.
7) Remove the USB stick from your navigation device.

8) Go to alpine.naviextras.com/shop/portal/downloads and follow the instructions on
naviextras.com website how to download and install Naviextras Toolbox.
9) Connect the USB stick to your PC.
10) Start Naviextras Toolbox. The USB stick will be recognized as your navigation device.
Push the button "Updates". If a pop-up window (see point 11) with the notification "You need
to upgrade your system by installing this mandatory update..." NOT appears go directly to
point 31 and follow the instructions from there.
11) Install the new navigation software with the Naviextras Toolbox. Press the "Install" button.
12) After transferring the data to the USB stick, the following screen is displayed.
Follow the instructions.
13) Safely remove the USB stick from your PC.

14) Reconnect the USB stick to your navigation device.
15) Go to Navigation → Main Menu → scroll to right → Update
Press the soft key “Update”.
16) The Update tool starts up.
The Initialization screen is displayed for approximately 2 to 4 minutes.
17) Then Confirm with soft key “Yes”. Confirm the dialog box by pressing "Install".

18) Navigation Software update is executed.
Do not disconnect the USB stick and do not power off the unit.
Please note: The Update process will take up to 2 minutes.
19) Confirm and finalize the update by pressing “Done”. Remove the USB stick from your
navigation device. The USB stick must be prepared again for the next step.
The navigation firmware was updated successfully.
20) Switch off the navigation device via ignition (ACC) for 2 minutes or perform a reset. Then
switch the navigation device on again.
21) Go to Main Menu → scroll to right → About →Version Information to check the latest
Navigation Software Version (9.35.2.263746 Sep 21 2021 or newer).

Map Update Process
22) Connect the USB stick (freshly FAT32 formatted) to the navigation system.
23) Go to Navigation →Main Menu → scroll to right →Update
Press the soft key “Update”.
24) The Update tool starts up.
25) Confirm with soft key “Yes”.

26) Device information transferred to the USB stick.
Do not disconnect the USB stick and do not power off the unit.
27) Confirm with “OK” and remove the USB stick from your navigation device.
28) Go online on alpine.naviextras.com/shop/portal/downloads and follow the instructions on
naviextras.com website how to download and install Naviextras Toolbox.
29) Connect the USB stick to your PC.
30) Start Naviextras Toolbox. The USB stick will be recognized as your navigation device.
31) Purchase and install content and updates as described within Naviextras Toolbox.
32) Safely remove the USB stick from your PC.

33) Reconnect the USB stick to your navigation device.
34) Go to Navigation → Main Menu → scroll to right → Update
Press the soft key “Update”.
35) The Update tool starts up.
The Initialization screen is displayed for approximately 4 to 10 minutes.
36) Then Confirm with soft key “Yes”.