Alpine 6LQ27TRMXX User manual

J E E P
W I R E LESS
SP EA KE R
Model 6LQ27TRMXX
US E R G U I D E

E N G L I S H | 2
GET TO KNOW YOUR SPEAKER
BATTERY STATUS BUTTON
RESET
EXTERNAL USB
CHARGING PORT
3.5 MM AUDIO IN JACK
SPEAKER CHARGING
PORT
BATTERY STATUS LED
SERVICE PORT
VOLUME UP,
SKIP TRACK (PRESS AND HOLD)
VOICE CONTROL,
ANSWER / END CALL
VOLUME DOWN,
SKIP BACK (PRESS AND HOLD )
PLAY / PAUSE
BLUETOOTH PAIRING
POWER ON / OFF

E N G L I S H | 3
UNDOCKING YOUR SPEAKER
Pull straight on the release strap to undock your wireless speaker.
Note: The speaker will be in the off state upon undocking from the vehicle dock.
DOCKING YOUR SPEAKER
First, set the wireless speaker onto the pivot in the bottom center of the vehicle dock. Then, lightly push against the speaker to rock it
back until the latch is completely closed.
Note: peaker Bluetooth functionality, button functionality, and LED functionality are disabled in the vehicle dock while your speaker
plays with your Jeep audio system.

E N G L I S H | 4

E N G L I S H | 5
P O W E R & BL U E T O O T H PA IR I N G
1. Press the power button for 2-3 seconds to turn your speaker on or off.
2 . Toggle Bluetooth® on in your device settings. For further instruction on how to do so, please
refer to the user manual included with your mobile device.
3 . Your speaker will automatically enter pairing mode when powered on. Pair a second device by
pressing and holding the Bluetooth® button for 2-3 seconds, until you hear the audio cue. Go to your
device’s
Bluetooth® settings and select “Jeep peaker” from the list.
Your speaker will remember the last 8 devices it has paired with.
NOTE: If your speaker is left on with an inactive Bluetooth® connection for 30 minutes, it will automatically power off. Power
your speaker on again by pressing and holding the power button for 2-3 seconds.

E N G L I S H | 6
VOL U M E A N D P L AY B A C K C ON T R OL
Increase volume by pressing the “+” button or decrease volume by pressing the “–” button. An audio cue will indicate
when you’ve reached max volume.
kip to the next track by pressing the “+” button or play the previous track by pressing and holding the “–” button.
C H A RG I NG YOU R SP E A K E R
Before using your Jeep wireless speaker for the first time, fully charge your speaker until the battery indicator light stays
solid green.
Charge your Jeep wireless speaker by installing it into the charging dock of your Jeep vehicle when it is in run/accessory. The
speaker also charges while using a compatible power adapter (not included). Plug the adapter into the speaker charging port on
the back of the speaker, then into a wall outlet.
MONITORING BATTERY LEVEL : Use the Battery tatus LED to monitor your speaker’s battery level.
Red = 30% or lower, Yellow = 30% - 70%, Green = 70% - 100%.
NOTE: The speaker must be turned on to observe the Battery tatus LED.

E N G L I S H | 4
C H A RG I NG E X T E R N A L D E V IC E S
Your speaker can charge most U B enabled smartphones and tablets using the full-sized U B port. To use
external charging:
1. Turn your speaker on.
2 . Plug your U B power cable into the U B port on the back of your speaker.
3 . Insert the other end of the cable into your device to immediately begin charging.
NOTE: External U B charging will be disabled when the speaker battery level reaches 30% or below (battery status LED is red). It will
automatically enable when the speaker has been charged back up to 50%.
SP E A K E R P H ON E
Press the mic button on your speaker to answer and end calls over the speakerphone.
WAT E R P R O O F F E AT U R E S
The Jeep wireless speaker is IP67 waterproof certified, designed to withstand a dunk in up to 3 feet / 1 meter of water for up
to 30 minutes.
IMPORTANT: Ensure your speaker is prepared for use in a wet environment by removing all cable connections and tightly
sealing the port cover. If the cover is not securely fastened, your speaker may sustain water damage.

E N G L I S H | 6
R E SE T T I NG YOU R SP E A K E R
Reset your Jeep wireless speaker to its original factory settings by pressing the reset button under the back cover for 8 -10
seconds.
O P ER AT I N G T EM P ER AT U R E
The Jeep wireless speaker battery will charge during 32 to 113 F (0 to 45 ° C). The speaker contains a lithium-ion rechargeable
battery. Typical charging temperatures for these types of batteries are from 32 to 113 ° F (0 to 45 ° C).
IMPORTANT : The functions described in this user guide only pertain to when your Jeep peaker is
unplugged from its dock. When plugged into the docking station, your speaker functions as part of your vehicle’s sound
system.

E N G L I S H | 7
WA R N I NG S, C A U T I O N
& L E G A L I N F O R M AT I ON
To reduce the risk of fire or electric shock, do not expose the Jeep
wireless speaker to rain or moisture while charging. The Jeep wireless
speaker should not be exposed to dripping or splashing, and objects filled
with liquids, such as vases, should not be placed on or near it while being
charged or charging other devices. As with any electronic products, use care
not to spill liquids into any part of the product. Liquids can cause a
failure and/or a fire hazard. The power supply must be used indoors
only. Make no modifications to the product or accessories. Unauthorized
alterations may compromise safety, regulatory compliance, and system
performance, and will void the warranty. Do not place any flame sources,
such as lighted candles, on or near the Jeep wireless speaker. The Jeep
wireless speaker contains small parts that may be a choking hazard and is
not suitable for children under age 3. Do not continue charging the
battery if it does not reach full charge within the specified charging time.
Overcharging may cause the battery to become hot, rupture, or ignite. If you
see any heat deformation or leakage, properly dispose of the battery. Do not
attempt to charge the battery in temperatures outside the range of 32°-
104°F (0° - 40°C). If the battery begins to leak, do not allow the liquid to
come in contact with your skin or eyes. If contact has been made, wash
the affected area with plenty of water and seek medical attention
immediately. Do not expose the product or battery to excessive heat,
including direct sunlight or fire and storage or use inside cars in hot
weather, where it can be exposed to temperatures in excess of 115°F
(60°C). Doing so may cause the battery and power supply to generate
heat, rupture, or ignite. Using the product in this manner also may result
in a loss of performance and a shortened life expectancy. Extended
exposure to direct sunlight may damage the external appearance and
material qualities. Do not step on, throw, or drop batteries or the power
supply or device, or expose them to a strong shock. Do not pierce, crush,
dent, or deform the batteries or power supply in any way. If either becomes
deformed, properly dispose of it. Do not short-circuit batteries. Do not
attempt to service the Jeep wireless speaker yourself. Opening or removing
covers may expose you to dangerous voltages or other hazards and will void
the manufacturer’s warranty. To prevent risk of fire or electric shock, avoid
overloading wall outlets, extension cords, or integral convenience receptacles.
Your Bluetooth device (mobile phone, music player, tablet, laptop, etc.) must
support the A2DP Bluetooth profile in order to work wirelessly with your new
Jeep wireless speaker. The A2DP profile is supported by most recent mobile
products with built-in Bluetooth capability. Please refer to your device’s user
manual for details and instruction regarding the Bluetooth profiles it
supports. This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Correct Disposal of this product. This marking indicates that this
product should not be disposed with other household wastes throughout
the EU. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle i t responsibly to promote the
sustainable reuse of material resources. To r e t urn your used device,
please use the r e t urn and collection systems or contact the
retailer where the product was purchased.
Jeep follows afety Instruction for CE- LV. Do not operate products
in temperatures outside the range of -5 to 40 °C. Operating
Frequency Band: 2402 MHz to 2480 MHz Maximum RF power: 6
dBm EIRP. Do not install this equipment in a confined or building-
in a space such as a book case or similar unit and remain a well
ventilation conditions. The ventilation should not be impeded by
covering the ventilation openings with items such as newspaper,
table- cloths, curtains etc .
WARNING: To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture. The apparatus shall not
be exposed to dripping or splashing and that objects filled with
liquids, such as vases, shall not be placed on apparatus.
WARNING: The power adapter is used when the device is
undocked from the vehicle so it can be readily charged outside
the vehicle.
WARNING: Please refer to the information on the bottom of the
speaker for electrical and safety information before installing or
operating the speaker.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type. The battery
(battery or batteries of battery pack) shall not be exposed to
excessive heat or fire.
Directive 2014/53/EU Article 10 Obligations of Manufacturers
2. Manufacturers shall ensure that radio equipment shall
be so constructed that it can be operated in at least one Member
tate without infringing applicable requirements on the use of
radio spectrum.
10. In cases of restrictions on putting in to service or of
requirements for authorization of use, information available on
the packaging shall allow the identification of the Member tates
or the geographical area within a Member tate where restrictions
on putting into service or requirements for authorization of use
exist. The Commission may adopt implementing acts specifying
how to present that information. Those implementing acts shall
be adopted in accordance with the advisor y procedure referred to
in Article 45 (2).

E N G L I S H | 6
CO M PLI ANCE INFO RMA T IO N
FCC
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:—
Reorient or relocate the receiving antenna. —
Increase the separation between the
equipment and receiver. — Connect the
equipment into an outlet on a circuit different
from that to which the receiver is connected.
— Consult the dealer or an experienced radio/
TV technician for help. CAUTION: Any changes
or modifications not expressly approved by the
party responsible for compliance could void
the user’s authority to operate the equipment.
FCC RADIATION EXPO URE TATEMENT:
To satisfy FCC RF exposure requirements for
mobile transmitting devices, a separation
distance of 20cm or more should be
maintained between the antenna of this
device and persons during operation.
To ensure compliance, operations at closer
distances than this are not recommended.
This device complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. The device has been evaluated
to meet the general RF exposure requirement.
This device complies with Industry Canada
license-exempt R standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference,
including interference that may cause
undesired operation of the device. Under
Industry Canada regulations, this radio
transmitter may only operate using an antenna
of a type and maximum (or lesser) gain
approved for the transmitter by Industry
Canada. To reduce potential radio
interference to other users, the antenna type
and its gain should be so chosen that the
equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for
successful communication. The device has
been evaluated to meet general RF exposure
requirement. This Class B digital apparatus
complies with Canadian ICE - 003. Lithium
Battery installed is not intended to be replaced
by the U ER. CAUTION: Danger of explosion if
battery is incorrectly replaced. Replace only
with the same or equivalent type. Where the
MAIN plug is used as the disconnect device,
the disconnect device shall remain readily
operable. The device meets the exemption
from the routine evaluation limits in section 2.5
of R 102 and compliance with R -102 RF
exposure, users can obtain Canadian
information on RF exposure and compliance.
This product complies with California
Energy Commission efficiency standards for
consumer battery chargers.
EUROPE
Alpine hereby declares that this
device is in compliance with Radio
Equipment Directive 2014 / 53 / EU.
The full text of the EU DoC is available
at the following:
https://www.alpine.com/j/research/do
c/
CANADA
This device complies with Innovation, cience,
and Economic Development Canada’s
licence exempt R s. Operation is subject to
the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR
d’Industrie
Canada applicables aux appareils radio
exempts de licence. L’exploitation est
autorisée aux deux conditions
suivantes :
1) l’appareil ne doit pas produire de
brouillage;
2) l’appareil doit accepter tout brouillage
radioélectrique
subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Pour satisfaire aux exigences de la FCC en
matière d’exposition aux radiofréquences
pour les appareils émetteurs mobiles, une
distance de séparation de 20 cm ou plus doit
être respectée entre l’antenne de cet
appareil et les personnes en fonctionnement.
Pour garantir la conformité, les opérations à
des distances plus rapprochées ne sont pas
recommandées.
CHINA
CMIIT ID: XXXXYZNNNNN
KOREA
M IP-XXX-ABC-12345678901234
MEXICO
IFETEL #: XXXXXXXXX
La operación de este equipo está sujeta a las
siguientes dos condiciones: (1) es posible que
este equipo o dispositivono cause
interferencia perjudicial y (2) este equipo o
dispositivo debe aceptar cualquier
interferencia, incluyendo la que pueda causar
su operación no deseada.
OMAN
RUSSIA
SOUTH AFRICA
OMAN-TRA
X/NNNN/YY
Dyynnnn