Altelix ZP120 User manual

s
AlteliConnect Enclosure For
SONOS Connect:Amp
™
©™
Installation Guide
SONOS® and Connect:Amp™ are trademarks or registered trademarks of
SONOS, Inc. Altelix and AlteliConnect™ are trademarks and/or registered
trademarks of Altelix LLC
Application Note: This enclosure is designed specifically for use only with the
SONOS® Connect:Amp™ (model #ZP120). The SONOS® ZonePlayer (model
ZP100)or the new SONOS® AMP (model #AMPG1US1BLK) are not compatible
with this enclosure model. Be sure to check the model on your SONOS® device
before ordering.

AlteliConnect Installation Guide
™
Installing the Connect:Amp™
Page-1
The Connect:Amp™ is held in place by two brackets which attach to the rear
plate.
Pre-installed Mounting
Bracket
1. Position the Connect:Amp™in the enclosure as shown fully up against the pre-
installed bracket ensuring the amp is under the foam padding on the bracket.
The amp should be orientated so the speaker cable connectors are facing the
enclosure’s hinge.
SONOS® and Connect:Amp™ are trademarks or registered trademarks of SONOS, Inc.
IS0118 Rev A 06/14/19
Altelix LLC USA: 866-660-WIFI (9434) International: [phone] [email protected] www.altelix.com
Copyright (C) 2017 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specifications are subject to change without notice. See www.altelix.com for most current information
Mounting Bracket and
Screws Included in
Accessory Kit
Front of Amp
Enclosure Hinge
Pre-installed Mounting
Bracket
Speaker Cable
Side of Amp

AlteliConnect Installation Guide
™
Page-2
2. Install the second mounting bracket included in the accessory kit using the (2)
suppled screws as shown to secure the Connect:Amp™. Attach the amp’s power
cord and plug into the internal 120VAC outlet. The power cord can be secured
using the include cable tie.
Wiring the Connect:Amp™
A rubber cable grommet is provided
on the side of the enclosure which
allows speaker and Ethernet cables
to be connected to the amp. To
provide power to the enclosure,
simply plug the enclosure’s 5 foot
power cord into a 120VAC outlet.
Install (2) Screws to
Secure Bracket
SONOS® and Connect:Amp™ are trademarks or registered trademarks of SONOS, Inc.
5 Foot Power Cord
Cable Grommet
Altelix LLC USA: 866-660-WIFI (9434) International: [phone] [email protected] www.altelix.com
Copyright (C) 2017 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specifications are subject to change without notice. See www.altelix.com for most current information
IS0118 Rev A 06/14/19

AlteliConnect Installation Guide
™
Page-3
Included in the accessory kit are (4) stainless steel mounting feet and screws. They
can be attached to the (4) threaded inserts located on the rear of the enclosure.
SONOS® and Connect:Amp™ are trademarks or registered trademarks of SONOS, Inc.
Mounting the AlteliConnect™ Enclosure
The AltelixConnect™ enclosure can be either wall mounted using the supplied
hardware or pole mounted using the optional NMKS-300-08 poll mounting kit
available from www.ALTELIX.com.
AltelixConnect™ enclosure shown with
optional NMKS-300-08 Pole Mounting Kit
Rear of Enclosure
Altelix LLC USA: 866-660-WIFI (9434) International: [phone] [email protected] www.altelix.com
Copyright (C) 2017 Altelix LLC. All rights reserved. Altelix and the Altelix logo are Trademarks and/or Registered Trademarks of Altelix LLC.
Specifications are subject to change without notice. See www.altelix.com for most current information
Mounting Feet
and Screws Threaded Insert
IS0118 Rev A 06/14/19