Altimeters PROTRACKII User manual

QUICK GUIDE
REV. 02, OCTOBER 2022
MAIN
WINDOWS
MM-DD
HH-MM
Flight Mode
Displays altitude
and clock while in
ight mode
Logbook Total Clock Setup
4 “climb to warning” banks.
Each bank supports up to 4
warning altitudes
Climb to Altitude
Warnings (CL)
This Road Map does not replace the
PROTRACK II™Manual nor releases the
user from the obligation to comply with the
contents of the PROTRACK II™Manual.
WARNING
Visit lbaltimeters.com
for manual
and support
Instructional videos
and YouTube
channel
Power OFF Power ON
Device Info
Firmware version
and serial number
In “Ground Mode” and if “ECO Mode” is enabled, The PROTRACK II™
automatically switches o󰀨 14 hours after the last jump or 14 hours after
pressing any button, whichever comes last.
The PROTRACK II™ can also be manually powered off from the Setup
Window, to further extend the battery life when not in use.
Note: When switched o, the PROTRACK II™ can not be used for jumping.
Customer settings are not lost when the unit is switched off.
Ground Mode
To save battery power, after power up and shortly after landing the PROTRACK II™ enters “Ground
Mode”. In this mode, 60 seconds after last button pressed, the display will switch off. However, the
PROTRACK II™ is still ready for jumping.
Flight Mode
Shortly after takeo󰀨 the PROTRACK II™ switches to “Flight Mode” and displays the “Flight Mode”
window. At the lowest preset “Climb to altitude” (factory preset to 1,000 feet), the PROTRACK II™
sounds a sequence of beeps. These beeps have two functions:
1. The beeps indicate that the PROTRACK II™ has calibrated itself to the local ground elevation and
is ready to jump.
2. The number of beeps indicate the altitude at which the high speed warning is set; for example: If
set to 4,500 feet, the sequence will be beep-beep-beep-beep (pause) beep. The number of rapid-
sequence beeps indicate the highest warning altitude in thousands of feet. The beep after the pause
(if any) signifies a 500-foot increment.
Should the battery voltage of the PROTRACK II™ be low, the beep sequence is followed by 5 short
beeps. This indicates that the battery should be replaced.
USB Mode
If a USB host device is connected to the PROTACK II™ USB port, the
PROTRACK II™ will act as a USB slave and show “USB” on the LCD display.
Visit www.lbaltimeters.com for applications that support PROTRACK II™.
Error Mode
When the PROTRACK II™ detects a fault, an error (“ERR”) sign, number, and
code is displayed. At the same time the unit beeps once every minute.
All faults indicate that the PROTRACK II™ is defective.
Remedy: Replace batteries or perform reset.
If the unit does not function correctly even after replacing the batteries and
pressing reset, please contact your local dealer or LB Altimeters.
The PROTRACK II™ has been turned
o󰀨 prior to shipping from our factory.
To turn the power on, press and hold
any key until the unit beeps, then
release the key.
When starting up, the PROTRACK II™
runs a self-test and beeps three times
while ashing the screen twice.
It then displays device info.
Battery capacity in mVolt
Barometric pressure in mBar (hPa)
Temperature (Celcius or Fahrenheit)
Free logbook storage in percent
Firmware version
Altitude O󰀨set Climb to altitude
warning options
High speed
warning options
Low speed
warning options
Clock options Setup options
( is factory defaults)
Logbook total
options
Logbook options
■ Change altitude ■ Select bank
■ Set or disable
warnings
■ Set volume
■ Set pitch
■ Hear selected
warnings, volume
and pitch
■ Select bank
■ Set or disable
warnings
■ Set volume
■ Set pitch
■ Hear selected
warnings, volume
and pitch
■ Select bank
■ Set or disable
warnings
■ Set volume
■ Set pitch
■ Hear selected
warnings, volume
and pitch
■ Set year
■ Set month
■ Set day
■ Set 12/24 hr clock
■ Set hour
■ Set minutes
■ Power OFF
■ AUT / ECO
■Beep on / o󰀨
■ Dive type*
■TAS / SAS
■ Feet / Meters
■ MPH / KM/H
■Celcius / Fahrenheit
■ Reset to factory
default
■ Set total number of
jumps
■ Set total hours
■ Set total minutes
■ Set total seconds
■ Delete complete
logbook
Caution
Once the logbook is
deleted there is no
way to restore the
information.
Press to view
“Remaining logbook
storage” window
Logbook screen 1
■ Jump number
■ Exit altitude
■ Deployment altitude
■ Freefall time
■ Speeds (scrolls
through AVG, MAX,
1st, and 2nd half)
Logbook screen 2
■ Jump number
■ Year for the jump
■ Month and date for
the jump
■ Hours and minutes
for the jump
■ Dive type
Logbook screen 3
■ Jump number
■ Altitude at time
■ Freefall and canopy
status
■ Time after exit in
seconds
■ Speed at time
Press to “Delete
last jump” window
Press to view
“Remaining logbook
storage” window
*Dive types:
■ ----- (Normal)
■ 3-SEC
In 3-SEC mode the descent rate parameters are more sensitive, allowing
detection of short freefall (>3 sec. freefall) for logbook exit generation.
See manual for important notes.
■ SLO (Slow)
In SLO mode the deployment parameters are more sensitive. Supports slow
falling types of dives, like normal wing suit dives etc.
■ S-SLO (Super slow)
In S-SLO mode the exit and deployment parameters are more sensitive. This
mode is for very slow wing suit dives, fast canopy descents, extreme relative
work (XWR) etc. All “high speed warnings” are enabled regardless of the
vertical air speed at the preset altitude. See manual for important notes.
Press and
hold
> 5 seconds
Error number
Error code
ACCESS ACCESS ACCESS ACCESS ACCESS ACCESS ACCESS ACCESS
ACCESS
Press and release the mode
button – the lock icon turns o󰀨
When the lock icon reappears,
immediately press and hold the
mode button – the lock icon
turns o󰀨 again
When the lock icon reappears,
release the mode button .
- The PROTRACK II™ is now in
ACCESS.
Note: The PROTRACK II™ exits ACCESS and returns
to the Main Window if no button has been pressed
within 30 seconds. ALL functions (except Power ON)
can be performed ONLY when the PROTRACK II™ is in
ACCESS mode.
To avoid any unintentional changes, all settings
are “locked” behind an ACCESS procedure.
ACCESS is required to unlock and change any
settings.
1
2
3
In main window
toggle left
In sub-menu
increase value
In main window
perform ACCESS
In sub-menu
set/next menu
In main window
toggle right
In sub-menu
decrease value
Logbook
4 “low speed warning” banks.
Each bank supports up to 4
warning altitudes
Low Speed
Decent Warnings (LO)
4 “high speed warning” banks.
Each bank supports up to 4
warning altitudes
High Speed Warnings
(HI)
Displays all stored
jumps
Displays any stored
logbook totals
Setup optionsDate and time in
device. Displays in
either 12 or 24 Hrs

ROAD MAP
This Road Map does not replace the
PROTRACK II™Manual nor releases the
user from the obligation to comply with the
contents of the PROTRACK II™Manual.
WARNING
Visit lbaltimeters.com
for manual
and support
Instructional videos
and YouTube
channel
REV. 02, OCTOBER 2022
ACCESS
MAIN
WINDOWS
ACCESS
Press and release the mode
button – the lock icon turns o󰀨
When the lock icon reappears,
immediately press and hold the
mode button – the lock icon
turns o󰀨 again
When the lock icon reappears,
release the mode button .
- The PROTRACK II™ is now in
ACCESS.
Note: The PROTRACK II™ exits ACCESS and returns
to the Main Window if no button has been pressed
within 30 seconds. ALL functions (except Power ON)
can be performed ONLY when the PROTRACK II™ is in
ACCESS mode.
To avoid any unintentional changes, all settings
are “locked” behind an ACCESS procedure.
ACCESS is required to unlock and change any
settings.
1
2
3
MM-DD
HH-MM
ACCESS ACCESS ACCESS ACCESS ACCESS ACCESS ACCESS
Flight Mode
Climb to Altitude
Warnings
High Speed
Warnings
Low Speed
Decent Warnings Logbook Logbook Total Clock Setup
Altitude O󰀨set Bank Set total jumps Year Switch o󰀨Logbook: Main information
Logbook: Date, time, and dive type
Logbook: Playback, Jump prole
BankBank
Warning 1 Set total hours Month ECO/AUTOWarning 1Warning 1
Warning 2 Set total minutes Day Turn beep on/o󰀨Warning 2Warning 2
Warning 3 Set total seconds 24/12 hour clock Dive typeDelete jumpWarning 3Warning 3
Warning 4 Delete logbook Hours TAS/SASRemaining logbook storage
Remaining logbook storage
To delete jump,
set ashing
value to 10
Press
to move
forward in
time.
Press
to move
back in time
To switch o󰀨,
set ashing
value to 10
To delete
logbook, set
ashing value
to 123
To reset to
facory default,
set ashing
value to 123
Free logbook
storage in
percent
In main window
toggle left
In sub-menu
increase value
In main window
perform ACCESS
In sub-menu
set/next menu
In main window
toggle right
In sub-menu
decrease value
Free logbook
storage in
percent
Warning 4Warning 4
Volume Minutes Feet/Meter
MPH/KMH
Celsius/Fahrenheit
Reset to factory default
Guide on/o󰀨Volume
Pitch VolumePitch
Test
Test
PitchTest