Altimium TP70WP User manual

TP70WP
HDBaseT Wall Plate Receiver
All Rights Reserved
Version: TP70WP_2016V1.1
User Manual

HDBaseT Wall Plate Receiver
Altimium www.altimium.com
Preface
Read this user manual carefully before using this product. Pictures shown in this manual
is for reference only, different model and specifications are subject to real product.
This manual is only for operation instruction only, not for any maintenance usage. The
functions described in this version are updated till December 2016. Any changes of
functions and parameters since then will be informed separately. Please refer to the
dealers for the latest details.
All product function is valid till 2016-12-2.
Trademarks
Product model, logo are trademarks. Any other trademarks mentioned in this manual
are acknowledged as the properties of the trademark owner. No part of this publication
may be copied or reproduced without prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

HDBaseT Wall Plate Receiver
Altimium www.altimium.com
SAFETY PRECAUTIONS
To insure the best from the product, please read all instructions carefully before using
the device. Save this manual for further reference.
Unpack the equipment carefully and save the original box and packing material for
possible future shipment
Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
Using supplies or parts not meeting the products’ specifications may cause damage,
deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this
product near water.
Do not put any heavy items on the extension cable in case of extrusion.
Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
Install the device in a place with fine ventilation to avoid damage caused by
overheat.
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If
an object or liquid falls or spills on to the housing, unplug the module immediately.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
Unplug the power cord when left unused for a long period of time.
Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

HDBaseT Wall Plate Receiver
Altimium www.altimium.com
Contents
1. Introduction.................................................................................................................1
1.1 Introduction to TP70WP.....................................................................................1
1.2 Features ............................................................................................................1
1.3 Package List......................................................................................................1
2. Panel Description........................................................................................................2
2.1 Front Panel........................................................................................................2
2.2 Rear Panel.........................................................................................................3
3. System Connection.....................................................................................................4
3.1 Usage Precautions............................................................................................4
3.2 System Diagram................................................................................................4
3.3 Connection Procedure.......................................................................................4
3.4 PoC/ PoE Solution.............................................................................................5
3.5 Application.........................................................................................................5
4. Specification ...............................................................................................................6
5. Panel Drawing ............................................................................................................7
6. Troubleshooting & Maintenance .................................................................................8
7. After-sales Service......................................................................................................9

HDBaseT Wall Plate Receiver
Altimium 1 www.altimium.com
1. Introduction
1.1 Introduction to TP70WP
TP70WP is a Decora style HDBaseT receiver that installs in a double-gang wall plate to
provide a convenient interface for HDMI / DVI output. It has 1 HDMI OUT, 1 HDBT IN
with PoC & PoE, 2 IR IN and 1 IR OUT. It supports HDMI 1.4& HDCP for reliable
transmission. HDBT IN is capable to transmit AV& control signal up to 70m, of which IR&
RS232 control signal can travel bi-directionally.
With its PoC/ PoE solution, TP70WP can be energized by far-end device whichever
supports PoC/ PoE.
1.2 Features
High bandwidth: 10.2Gbps
Wide resolution range (from 480p to 4Kx2K)
Compliant with HDMI 1.4, support 1080p 3D
HDCP compliance, equipped with HDCP auto-tracking
Bi-directional IR& RS232 control
Powered by local power pack or power sourcing equipment via PoC/ PoE solution
Aluminium design for elegant and better cooling
1.3 Package List
1 x TP70WP
2 x Screws
1 x Face Plate (2 gang)
2 x Screws (for face plate)
4 x Pluggable Terminal Blocks (2 2-pin block, 2 3-pin block)
1 x Power Adapter (DC 12V 1A, selectable)
1 x User Manual
Notes：Please confirm if the product and the accessories are all included, if not, please
contact with the dealers.

HDBaseT Wall Plate Receiver
Altimium 2 www.altimium.com
2. Panel Description
2.1 Front Panel
Figure 2- 1 Front panel
No.
Name
Description
①
Power
indicator
Illuminates red when powered on
②
HDMI OUT
Connect with HDMI display
③
LINK
&HDCP
LINK: Twisted Pair Link status indicator, illuminate green
when successfully connected.
HDCP: HDCP compliance indicator, illuminate green when
the source signals is with HDCP; blink when it is not with
HDCP; and turn off when there is no source signal.
④
IR
In-built IR sensor

HDBaseT Wall Plate Receiver
Altimium 3 www.altimium.com
2.2 Rear Panel
Figure 2- 2 Rear panel
No.
Name
Description
①
PoC IN&
HDBT IN
RJ45 port, connect with transmitter via a CAT5e/6 cable to
deliver AV& control signals, support PoC.
②
IR IN
Connect with IR receiver, receive IR signals sent from the IR
Emitter connected to the far-end receiver
③
IR OUT
Connect with IR Emitter, IR signals emitted from the IR emitter
are received by the IR receiver connected to the far-end
receiver.
④
RS232
Serial port, connects with a far-end receiver, supports
bi-directional RS232 control (send control signal from local or
receive control signal sent from far-end devices).
⑤
Power
Connect with DC 12V power adapter
Note:
1．TP70WPcan be energized via standard PoC& PoE, i.e. it can be energized by
far-end device.
2．Once connecting an IR Receiver to the IR IN socket, both the in-built IR sensor and
the extended IR Receiver is capable to collect IR signal.
3．Pictures shown in this manual are for reference only, different model and
specifications are subject to real product.
PoC IN
HDBT IN
RS232
12V
POWER Tx Rx
IR IN
SIG
IR OUT SIG 5V
5V

HDBaseT Wall Plate Receiver
Altimium 4 www.altimium.com
3. System Connection
3.1 Usage Precautions
1) System should be installed in a clean environment and has a prop temperature and
humidity.
2) All of the power switches, plugs, sockets and power cords should be insulated and
safe.
3) All devices should be connected before power on.
3.2 System Diagram
The following diagram illustrates typical input and output connections that can be
utilized with TP70WP (exampled by HDBaseT Twisted Pair PoC Transmitter):
Figure 3- 1 System connection
3.3 Connection Procedure
Step1.Connect HDMI source device (e.g. Blue-ray DVD) to HDMI IN socket of the
HDBaseT Twisted Pair PoC Transmitter with HDMI cable.
Step2.Connect the HDBT ports of HDBaseT Twisted Pair PoC Transmitter and
TP70WP.
Step3.Connect a HDMI display to the HDMI OUT port of TP70WP.

HDBaseT Wall Plate Receiver
Altimium 5 www.altimium.com
Step4.Connect a control terminal (e.g. a PC) to the RS232 port of either HDBaseT
Twisted Pair PoC Transmitter or TP70WP.
Step5.Both HDBaseT Twisted Pair PoC Transmitter and TP70WP have IR IN and IR
OUT sockets. When one model is used for IR signal receiver, the IR signal must
be sent out by the other model.
For example: When “IR IN” of TP70WP connects with an IR receiver, the IR
emitter must connect to IR OUT of HDBaseT Twisted Pair PoC Transmitter.
Step6.Connect a DC 24V power adaptor to the power port of HDBaseT Twisted Pair
PoC Transmitter.
Note: IR& RS232 signal can be transmitted bi-directionally between TP70WP and
HDBaseT Twisted Pair PoC Transmitter.
3.4 PoC/ PoE Solution
Apart from power supply, TP70WP can be energized by far-end devices that support
PoC/ PoE, which increases the system flexibility.
Connect the receiver and far-end device (exampled by HDBaseT Twisted Pair PoC
Transmitter) via a CAT5e/6 cable as below:
Figure 3- 2 PoC Solution
AV and IR& RS232 control signal can also be transmitted via the cable.
Note: TP70WP supports unidirectional PoC/ PoE, i.e, TP70WP can get power from
far-end PoC/ PoE devices.
3.5 Application
TP70WP has a good application in various occasions, such as computer realm,
monitoring, conference room, big screen displaying, television education, command &
control center and smart home etc.

HDBaseT Wall Plate Receiver
Altimium 6 www.altimium.com
4. Specification
Note: All nominal levels are at ±10%.
Video
Input
1 HDBT
Output
1 HDMI
Input
Connector
1 RJ45
Output
Connector
1 19-pin Type A HDMI
female
Transmission
Distance
1080P≤20M
4Kx2K≤15M
Control Parts
Control Ports
1 RS232
2 IR IN (1 in-built IR sensor on front panel, 1 3.5mm IR IN on rear
panel
1 IR OUT
General
Resolution
HDMI:4Kx2K, 1080P 3D, 1080P, 1080i, 720P, 576P, 576i, 480P,
480i
DVI:1920x1200@60Hz, 1920x1080@60Hz, 1600x1200@60Hz,
1280x1024@75Hz, 1280x1024@60Hz, 1024x768@75Hz,
1024x768@70Hz, 1024x768@60Hz, 800x600@75Hz,
800x600@72Hz, 800x600@60Hz, 640x480@75Hz,
640x480@72Hz, 640x480@60Hz
Transmission
Distance
1080P≤70M (PoC)
4Kx2K≤40M (PoC)
Bandwidth
10.2Gbps
HDMI
Standard
Support HDMI1.4 and HDCP
Chassis
Dimension
Decora style two gang
Power
Consumption
7w (Max)
Power
Supply
DC 12V 1A
Temperature
0 ~ 55℃
Reference
Humidity
10% ~ 90%
Dimension
(W*H*D)
89x 104 x 35 mm
Weight
0.24Kg

HDBaseT Wall Plate Receiver
Altimium 7 www.altimium.com
5. Panel Drawing
89 mm
PoC IN
HDBT IN
RS232
12V
POWER Tx Rx
IR IN
SIG
IR OUT SIG 5V
5V
PoC IN
HDBT IN
RS232
12V
POWER Tx Rx
IR IN
SIG
IR OUT SIG 5V
5V
104 mm
69 mm
LINK HDCPPOWER
HDMI OUT

HDBaseT Wall Plate Receiver
Altimium 8 www.altimium.com
6. Troubleshooting & Maintenance
Problems
Causes
Solutions
Color losing or no video
signal output in HDMI
display
The connecting cables may
not be connected correctly
or it may be broken
Check whether the cables
are connected correctly
and in working condition.
No HDMI signal output in
the device while local
HDMI input is in normal
working state
Output image with
snowflake
POWER indicator doesn’t
work or no respond to any
operation
Loose or failed power cord
connection
Ensure the power cord
connection is good
Cannot control the device
by control device (e.g. a
PC) through RS232 port
Wrong RS232
communication parameters
Make sure the RS232
communication parameters
are correct.
The unit is broken
Send it to authorized
dealer for repairing.
Static becomes stronger
when connecting the video
connectors
bad grounding
Check the grounding and
make sure it is connected
well.
If your problem persists after following the above troubleshooting steps, seek further
help from authorized dealer or our technical support.

HDBaseT Wall Plate Receiver
Altimium 9 www.altimium.com
7. After-sales Service
If there appear some problems when running TP70WP, please check and deal with the
problems reference to this user manual. Any transport costs are borne by the users
during the warranty.
1) Product Limited Warranty: We warrant that our products will be free from defects
in materials and workmanship for three years, which starts from the first day you
buy this product (The purchase invoice shall prevail).
Proof of purchase in the form of a bill of sale or receipted invoice which is evidence
that the unit is within the Warranty period must be presented to obtain warranty
service.
2) What the warranty does not cover:
Warranty expiration.
Factory applied serial number has been altered or removed from the product.
Damage, deterioration or malfunction caused by:
Normal wear and tear
Use of supplies or parts not meeting our specifications
No certificate or invoice as the proof of warranty.
The product model showed on the warranty card does not match with the
model of the product for repairing or had been altered.
Damage caused by force majeure.
Servicing not authorized
Any other causes which does not relate to a product defect
Delivery, installation or labor charges for installation or setup of the product
3) Technical Support: Email to our after-sales department or make a call, please
inform us the following information about your cases.
Product version and name.
Detailed failure situations.
The formation of the cases.
Remarks: For any questions or problems, please try to get help from your local
distributor.

ALTIMIUM
587 Avenue Blaise Pascal
77550 MOISSY-CRAMAYEL
Tél : [phone]
Fax: [phone]
Mail: [e-mail]
Web: www.altimium.com