Altura Photo 702168588511 User manual

DUAL WIRELESS FLASH TRIGGER SET
USER'S MANUAL
www.alturaphoto.com

Thank you for purchasing the Altura Photo Wireless Remote Control & Flash Trigger Kit.
Please refer to the instructions below to properly understand the functionality of these
items.
USER GUIDE
1
TRANSMITTER
1
2
3
4
5
1Shutter release / test button
2Indicator light
3Trigger point
4Battery cover
5ACC1 socket

RECEIVER
1
2
3
4
5
6
1Hot shoe socket
2Mode switch
3Indicator light
4Hot shoe socket
5Battery cover
6ACC2 socket
2

FOR YOUR SAFETY
Do not disassemble or modify the product.
Keep the product dry.
Keep the product out of reach from children.
Do not use the product in the presence of flammable gas.
Do not expose the product to high temperatures.
FEATURES
The Altura Photo series 3-in-1 Wireless Flash Trigger & Remote Control is a versatile and
reliable control kit. These units have the ability to trigger external flash units and studio lights
from up to 100 feet (30 meters) away.
3

The Altura Photo series also functions as a wireless camera shutter release – ideal for
wildlife, macro, and portrait photography where even the slightest camera shake can ruin a
shot. This prevents the Altura Photo Trigger from picking up radio interference and extends
its range when working on the 433MHz frequency. You won't need to have line-of-sight
alignment because radio waves will pass through solid barriers such as walls and floors.
NOTICE!
The Altura Photo Trigger does not transmit TTL settings. Therefore, it is recommended that
you use a flash or light unit with full manual control. You need to set the power output
manually.
-Wireless Frequency System: 433MHz
-Operating Distance: up to 30 meters (100 feet)
-16 Selectable Channel Combinations
-Receiver includes 1/4"-20 tripod mount
SPECIFICATION
-Sync: 1/250s
-Transmitter power: 1 x 23A battery
-Receiver power: 2 x AAA batteries
4

1.Wired Remote Control (for DSLR camera with remote socket)
2.Wireless Remote Control (for DSLR camera with remote socket)
3.Wireless Flash Trigger (for camera speedlite or studio light)
Weight:
Transmitter: 30g (without battery)
Receiver: 42g (without battery)
Dimensions:
Transmitter: 62.6 x 39.2 x 27.1mm
Receiver: 79.9 x 37.8 x 33.2mm
FUNCTIONS
5

-Altura Photo's transmitter and receiver channel switches are inside the battery hatch.
-Follow the OPEN direction icon to slide out the battery door and set the channel.
-There are 16 Channel combinations for the transmitter and receiver.
-Please make sure both the transmitter and receiver are on the same channel.
CHANNEL SETTING
ON DIP
1 2 3 4
ON DIP
1 2 3 4
REPLACING TRANSMITTER
BATTERIES:
1. Slide out the battery cover from the transmitter.
2. Remove the battery (23A battery).
3. Insert one (1) 23A fresh battery.
6

REPLACING RECEIVER
BATTERIES:
1.Turn OFF the receiver unit.
2. Slide out the battery cover from the receiver unit.
3.Remove the batteries.
4. Insert two fresh AAA batteries.
WIRELESS FLASH TRIGGER:
7

1. Turn OFF the power of both the camera and receiver.
2. Mount the transmitter onto the camera’s hot shoe socket.
3. Mount the flash onto the receiver’s hot shoe socket.
4. If your flash or studio light do not have hot shoe entries, connect the studio light cable to
the flash or studio light to the ACC2 socket of the receiver.
5. Set the channel switches to the same position on both the transmitter and receiver.
(When using multiple flash units, verify that all receivers are set to the same channel.)
6. Switch the receiver mode to “Flash” mode.
7. Press the test button on the transmitter to confirm interaction.
8. If the transmitter and receiver status lights turn red while the flash trigger light turns on, all
settings are correct.
8

1. Turn the camera OFF.
2. Connect the shutter release cable to the ACC1 socket of the transmitter and to the
remote input on the camera body.
3. Turn the camera ON.
4. Press the test button on the transmitter.
5. Half press the transmitter’s button for autofocus and fully press for shutter release.
WIRED SHUTTER RELEASE:
WIRELESS SHUTTER RELEASE:
9

1. Turn both the camera and receiver OFF.
2. Mount the receiver to the camera’s hot shoe socket. Connect the shutter release cable
to the ACC2 socket of the receiver and to the remote socket on the camera body.
3. Set the channel switches to the same combination on both the receiver and transmitter.
(When using several camera units, make sure all receivers are set to the same channel
settings.)
4. Turn the camera ON and switch the receiver to “Camera” mode.
5. Press the button on the transmitter to confirm interaction.
6. Half press the transmitter’s button for autofocus and fully press for shutter release.
7. If the transmitter and receiver status lights turn red while the flash trigger light turns on, all
settings are correct.
10

Your Altura Photo Wireless Flash Trigger has been manufactured to the utmost standards of
quality. Altura Photo guarantees that this product will not contain any defects caused by
manufacturing processes, workmanship, or materials for one (1) year. This guarantee starts
from the date of purchase. Altura Photo will, at its discretion, either repair or replace prepaid,
returned equipment free of charge.
ONE YEAR LIMITED
WORLDWIDE WARRANTY
11

For more information about this product, go to
www.AlturaPhoto.com and search
the keyword: "Wireless Flash Trigger."
12