Amana B136CAL3 Manual

February1998 1 12074208
Amana Technical Information—Refrigerator



B136CAL3 P1318401W B136CAR3 P1318402W
B136CAL1 P1318403W B136CAR1 P1318404W
Return Technical Sheet to envelope after service
Kw/24 hr ±0.4 Percent Run
Time ±10% Cycles/24 hr
±25%
Refrigerator Center
Compartment Food
Average Temperature
±3°F
Freezer
Compartment
Food Average
Temperature ±3°F
Ambient°F65°90°110°65°90°110°65°90°110°65°90°110°65°90°110°
1.2 2.3 4.2 28 52 100 30 32 0 39 39 45 3 3 3
Temperature Relationship Test Chart
T-1 Outlet ±3°F T-1 Inlet ±3°FT-3 Suction
Line
±7°F
Average Total
Wattage ±10% Suction Pressure
±2 PSIG Head Pressure ±5 PSIG
Ambient°F65°110°65°110°65°110°65°110°65°110°65°110°
-14 -14 -14 -14 25 103 157 168 0 0 110 157
• Duetoapossibilityofpersonalinjuryorpropertydamage,alwayscontactanauthorizedtechnicianfor
servicingorrepairofthisrefrigerator.
• RefertoServiceManualRS1200001fordesign,disassembly,icemaker,safety,testing,and
troubleshootinginformation.
Toavoidelectricalshockwhichcancauseseverepersonalinjuryor death, disconnect powertorefrigeratorusing
powerswitch beforeservicing.Wiresremovedduringdisassemblymustbereplacedonproperterminalstoinsure
correctearthingandpolarization.Afterservicing,reconnectpowerusingpowerswitch.
Model B136CAL B136CAR
Capacity 21 cu ft 21 cu ft
Electrical
requirements
separate
circuit
115 VAC 60 Hz
15A 115 VAC 60 Hz 15A
Refrigerant
type R134a R134a
Width
without side
extrusions
35″35″
Depth
without handle
includes door
extrusions
237/8″237/8″
Height range
rollers to top of
air grille
831/4″–841/4″831/4″–841/4″
!
WARNING

12074208 2 February1998
Refrigerant Flow
(ACCESSIBLE
FROM REAR)
PRECONDENSER
SERPENTINE
EVAPORATOR
COMPRESSOR
DISCHARGE TUBE
COMPRESSOR
CONDENSER
DRIER
SUCTION
TUBE
CAPILLARY
TUBE
PRECONDENSER
LOOP (FOAMED
IN PLACE)
CONDENSATE
EVAPORATION
DC FAN
(ELECTRONICALLY
CONTROLLED)
CONDENSATE
PAN

February1998 3 12074208
Cabinet Air Flow
REFRIGERATOR AIR
SUPPLY TUNNEL TO
FRESH FOOD DC FAN
(ELECTRONICALLY
CONTROLLED)
DELI DRAWER
AIR SUPPLY
EVAPORATOR
FAN ASSEMBLY
REFRIGERATOR
RETURN AIR
TUNNEL
EVAPORATOR
CONDENSATE
EVAPORATION
DC FAN
(ELECTRONICALLY
CONTROLLED)
REFRIGERATOR
RETURN AIR
TUNNEL

12074208 4 February1998
Machine Compartment Air Flow
CONDENSER CONDENSER
FAN ASSEMBLY
COMPRESSOR

February1998 5 12074208
Component Specifications
Component Description Test Procedures
A3079001 Bulb Volt
Watt 115 VAC 40 watts
C8931604 Capacitor, compressor run Volt
Capacitance 220 VAC 15 Mfd +10%
-5%
12049702 Compressor Type
BTUH
Volt
Watt
Current
Lock rotor
Full load
Resistance
Run Windings
Start Windings
Fan Cooled, R134a refrigerant
970 BTUH
115 VAC 60 Hz
176 watts
21.3 A
1.6 A
2.60 Ω
4.35 Ω
B2150504 Drier Drier must be changed every time the system is opened for testing or
compressor replacement.
Desiccant (20) 8 x 12 4AXH - 7 M.S. -Grams
10428411 Heater, evaporator Volt
Wattage
Resistance
115 VAC
450 ± 5% W
30 ± 5% Ω
Volt
Wattage
Resistance
115 VAC
20 W
661 ±7.5 Ω
12401301 Heater, mullion
For service use only.
Foamed in place. Not powered from
the factory.
To avoid risk of electrical shock which can cause death or
severe injury, disconnect electrical power to unit before
servicing.
To connect mullion heater to power:
1. Disconnect power to unit using power switch.
2. Remove toe grille. Locate water valve wiring harness.
3. Carefully, slit wiring harness vinyl sleeve to expose one black and
one white lead bent with bullet terminators.
4. Locate mullion heater leads at the left side of cabinet and connect to
black and white leads.
5. Wrap vinyl sleeve with electrical tape to close slit.
12106801 High voltage circuit board, PC See "Electronic Functional
Description"
12067101 Low voltage circuit board, PC See "Electronic Functional
Testing"
WARNING
!

12074208 6 February1998
Component Specifications
10522103 Motor, condenser PSC Volt
Rotation (facing end opposite
shaft)
RPM
Watt
Current
Resistance
115 VAC, 60 Hz
Clockwise
1300 RPM
6.4 W
0.05 A
480 Ω
10654207 Motor, ECM evaporator fan Volt
Rotation (facing shaft)
RPM
Watt
115 VAC, 60 Hz
Counterclockwise
2150 RPM
2.2 W
12075003 Motor and blade, refrigerator fan and
condensate evaporation fan Volt Rotation (facing shaft)
RPM
Watt
24 VDC
Counterclockwise
3300 RPM
1.4 watts
10377015 Overload Volt
Ult. trip amps @ 158°F (70°C)
Close temperature
Open temperature
Short time trip (seconds)
Short time trip (amps @ 77°F
(25°C))
115 VAC
3.51 A
142°F (61°C) ±9°
257°F (125°C) ±5°
10 seconds
14 A
10097202 Relay Resistance
With power off check:
Across terminals 2 & 3
Shorted
Open
312 Ω
0 Ω
Very high or infinite ohms
12235201 Switch, Keyboard
C3680306 Switch, auger interlock Type
Volt
Current
DPST, NO
250/125 VAC
10/5 A
12074904 Switch, refrigerator light (left opening
door hinge) Type Volt
Current
SPST, NC
125/250 VAC
3 A
S10S9S8S7S6S5S4S3S2S1
1
3
6
PINNO.
7
4
8
5
PERIMETER
STATIC GUARD
Switch Functions
Display On S1
Freezer Temperature S2
Refrigerator Tem perature S3
Warmer S4
Colder S5
S6
Max Cool S7
Fast Freeze S8
Alarm Off S9
Display Off S10
*

February1998 7 12074208
Component Specifications
Additional Part Numbers
12196401 Basket,bottom feezer
12234601 Basket,top freezer
B5742603 Blade,condenserfan
12059901 Blade,evaporatorfan
12061902 Condenserassembly
12056901 Crisperpanassembly
12144601 Crisper,pan
12073101 Delidrawerlid
12073201 Delidrawertop
12073301 Delidrawer
12039601 Doorshelfassembly(refrigerator)
12039701 Doorshelfassembly(refrigerator)
12097401 Dairymodeuleassembly
14036505 Eggtray
12179801 Evaporator
10933002 Gasket,freezerdoor
10933001 Gasket,refrigeratordoor
D7813004 Harness,ice maker
12193401 Icepan
R0167203 Module & motor assembly, ice maker
R0156669 Mold & heater assembly, ice maker
12201601 Overlay,keyboard
12021401 Shelf,crisper
12021301 Shelf,refrigerator
12104901 Shelfsnugger
12296301 Shut off arm, ice maker
12096901 Socket, light
R0161060 Thermostat,icemaker(order
R0195019cementalumilasticalso).
10423129 Utility bin
14036404 Utility bin lid
12074906 Switch, refrigerator light (right opening
door hinge) Type Volt
Current
SPST, NC
125/250 VAC
3 amps
12074801 Switch, power Type
Volt
Current
DPST
125 VAC
15 A
12401402 Switch, freezer light, sealed Type
Volt
Current
SPST, NC
125/250 VAC
5.0/5/0 A
10544502 Switch, showroom Type
Volt
Current
SPDT
125 VAC
6 amps
C8983701 Thermistor Check resistance across
terminals
Bell Curve resistance (See
Page 11)
@77°F
@45°F
30,000 ohms ±1% ohms
68,200 ohms ±2% ohms
10442407 Thermostat Volt
Watt
Current
Resistance across terminals
Above 55° ±6°F
Below 20° ±8°F
Between 55° ±6°F and
20° ±8°F
120 VAC
1000 watts
10 amps
Open
Closed
Will stay in current state (either open or
closed) until either 55° ±6°F and 20°
±8°F is reached.
12070801 Valve, water Volt
Watt
Water pressure (inlet)
Max
Min
Fill rate
120 VAC, 60 Hz
20 watts
120 PSI
20 PSI
140 ±10 CC's at 7.5 seconds

12074208 8 February1998
Display Panel
Display Panel
Keyboard
*
Display
On Freezer Temp Ref
Temp Warmer Colder Max
Ref Max Frz Alarm Off Display Off
FRZ
TEMP
COLDEST
REF
TEMP DOOR
OPEN
HIGH
TEMP MAX
REF
MAX
FRZ
Display
On Freezer Temp Ref
Temp Warme Colder Max
Ref Max Frz Alarm Off Display Off
FRZ
TEMP
COLDEST
REF
TEMP DOOR
OPEN MAX REF
MAX
FRZ
HIGH
TEMP
Temperature
Display Lights
*

February1998 9 12074208
Max Ref Pad
ActivatesMaximumrefrigeratormodesetting
refrigeratortocoldestsettingfor24hoursoruntil
MaxRef padispressedagain.
1. Refrigeratorindicatorlightwillglow.
2. ToadjustmaximumrefrigeratortimerefertoMode
Bfunctions.
Alarm Off Pad
Turnsoffalarmsignals.SeeAlarmssectiontointerpret
alarmsignals.
1. Pressandhold AlarmOff pad for 3 seconds to
deactivateDoorOpenalarm.ToreactivateDoor
Openalarm,pressandhold AlarmOff padfor3
seconds.
2. If AlarmOff padispressedand conditioncausing
alarmis notcorrected, alarmwill reset.
*
Activates ProgramMode. SeeProgramModesection
fordescriptionoffunctionsavailable.
1. Openrefrigeratordoor.
2. PressDisplayOn pad.
3. Press *pad.
4. Within6seconds press thefollowing pads inthis
sequence: MaxRef,MaxFrz,MaxRef,MaxFrz.
5. Tonewill sound 3timesandcontrolwillbe in
programmodeA.
Display Off Pad
1. Deactivatescontrolpanel.
2. Deactivatestemperatureindicationareaofcontrol.
panel.
Display Panel Operation
Keyboard Pad Functions
EntryTone
Indicatesapadwaspressed,commandreadand
accepted.Turnoffentrytonebypressingandholding
DisplayOn padfor3 to 5 seconds.
Command Accepted Tone
Threeshorttonesindicatecommandaccepted.
Display On Pad
1. Activatescontrolpanel.Controlpanelremains
activeatleast10minutes.
2. TurnsoffPowerUpAlarm(flashinglights)after
powerisfirstpluggedinorafterpoweroutage.
Note: All pads, except Alarm Off , are inactive until
DisplayOn ispressed.
Freezer Temp Pad
Activatesfreezertemperaturesettingmode.
1. Freezerindicatorlightwillglow.Freezer
temperaturesettingwillbedisplayed.Factory
setting is 5 .
2. Changefreezertemperaturesettingbypressing
Warmer or Colder pad.
Ref Temp Pad
Activatesrefrigeratortemperaturesettingmode.
1. Refrigeratorindicatorlightwillglow.Refrigerator
temperaturesettingwillbedisplayed.Factory
setting is 5 .
2. Changerefrigeratortemperaturesettingbypressing
Warmer or Colder pad.
Warmer Pad
Raisestemperature settingonebaratatime.Ifentry
toneis on, tonewill soundat eachbarlevel untiltop
levelisreached.
1. Turnontemperaturesettingfunctionofcontrol
panelbypressing Warmer pad.
2. Pressandhold Warmer padtoraisetemperature
setting at a faster rate.
Colder Pad
Lowerstemperaturesettingonebaratatime.Ifentry
toneison, tone willsound at eachbarlevel untilbottom
levelisreached.
1. Turnontemperaturesettingfunctionofcontrol
panelbypressing Colder pad.
2. Pressandhold Colder padtolowertemperature
setting at a faster rate.
Max Frz Pad
ActivatesMaximumfreezermodesettingfreezer
temperaturetocoldestsettingfor24hoursoruntil
MaxFrz padispressedagain.
1. Freezerindicatorlightwillglow.
2. Toadjustmaximumfreezermodetimereferto
ProgramModeBfunctions.

12074208 10 February1998
Electronic Functional Description
ThermistorAlarm
Alarmsoundsandfreezerorrefrigeratorindicatorlight
showsandtemperatureindicators4through7willturn
oninsequenceifeitherthermistorcircuitopens.Refer
toTemperatureControlOperationSectionand
ElectronicTestingSection.
1. Press AlarmOff pad to turn off alarm.
2. Alarmwillretestfornormaloperation.Ifcondition
hasnotbeencorrected,alarmwillsoundagain.
Power Disconnect Switch
Usepowerdisconnectswitchtodisconnectpower
withoutunpluggingrefrigerator.Powerdisconnect
switchis locatedbehind air grille on topright side.
Refrigeratorisshippedwithpowerdisconnectswitchin
the on position.
Showroom Switch
Showroomswitchallowselectroniccontrolsand
interiorlightstofunctionindependentlyofrefrigeration
system.Showroom switch is located behind air grille to
rightofcontrolpanel.Refrigeratorisshippedwith
showroomswitchin unit run position.
Power
switch
Showroom
switch
Alarms
Alarms
Power Up Alarm
Afterpowerisinitiallypluggedin,afterapowerloss,or
ifpowerswitchisturnedoff,alltemperatureindicator
lights will flash until Alarm Off or Display On is
pressed.
Note: Allsettings return to default factorysettings.
Door Open Alarm
Alarmtonesoundsandindicatorlightsblinkifeither
refrigeratororfreezerdoorisopenmorethan3minutes.
1. TurnoffDoorOpenalarmbypressing AlarmOff
padorbyclosingdoor.
2. Deactivatedooropenalarmbypressing Display
On padandthen press andhold AlarmOff padfor
3 seconds.
3. DooralarmdelaycanbeadjustedinProgram
ModeB.
High Temperature Alarm
Alarmsoundsandindicatorlightshowsiffreezeror
refrigeratortemperaturehasgoneabovecriticallevel
andremainedwarmfor2hours.Alarmtonestopsif
temperaturefallsagain.
1. Criticaltemperatureforfreezeris+15°F;for
refrigeratorcriticaltemperatureis+55°F.
2. Press AlarmOff pad to turn off alarm.

February1998 11 12074208
Electronic Functional Description
Temperature Control Operation
Foranytemperaturesetting,outputswillbeturned
off/onbasedoncut-in/cut-outtemperaturesdetermined
byresistancelevelsoffreezerandrefrigerator
thermistors.
Refrigerator and Freezer Thermistor
Part#C8983701
Temp
°F (°C) Resistance Ohms Temp °F (°C) Resistance Ohms
-20 (-29) 495600 36 (2) 87510
-15 (-26) 418200 38 (3) 82740
-9 (-23) 354000 39 (4) 78300
-6 (-21) 300600 43 (6) 74100
-4 (-18) 256200 45 (7) 70170
5 (-15) 218850 46 (8) 66450
10 (-12) 187470 48 (9) 62970
16 (-9) 161040 50 (10) 59670
19 (-7) 138690 55 (13) 52290
25 (-4) 119760 61 (16) 45900
30 (-1) 103680 64 (18) 40410
32 (0) 97920 70 (21) 36540
34 (1) 92550 77 (25) 30000
Astemperaturedecreases,resistanceincreases.
Astemperatureincreases,resistancedecreases.
Openthermistororthermistorcircuitwill result in
failureofrefrigeratortocool.
Shortedthermistorwillcauserefrigeratortorun100
percentoftimeexcept for defrostcycle.
• Freezertemperaturesettingandthermistorvalue
willdetermineifcompressor/condenserfanand
evaporatorfanswitchesareopenorclosed.
Compressor/condenserfanswitchmustbeopenfor
6minutes beforeswitchcancloseagain
(compressordwelltime).
• Refrigeratortemperaturesettingandthermistor
valuewilldetermineiffreshfoodfanswitchisopen
or closed.
• Cut-outandcut-intemperaturevaluesmustbe
reachedandmaintainedfor15secondsbefore
outputstatewill change(digitaldelay).
• Refrigeratorandfreezercontrolcalibrationcanbe
adjustedinProgramModeB.
Factory set freezer and refrigerator settings
Part#120671001
Frozen
Food Fresh Food Level
Cut-out
F° (C°) ±
1.5°
Cut-out
F° (C°) ±
1.5°
-10 (-23) 29 (-2) 9
-8 (-22) 31 (-0.6) 8
-6 (-21) 33 (-0.6) 7
-5 (-21) 34 (1) 6
-4 (-20) 35 (2) 5
-3 (-19) 36 (2) 4
-2 (-19) 37 (3) 3
0 (-18) 39 (4) 2
2 (-17) 41 (5) 1
-10 (-23) ---- Max Ref
---- 29 (-2) Max Frz

12074208 12 February1998
Electronic Functional Description
Adaptive Defrost Operation
Defrostoccursafterpredeterminedlengthof
compressorrunhours.Compressorruntimebetween
defrostschanges,oradapts,dependinguponrecent
historyofdefrostlengths(timeit takes fordefrost
terminatortoopenafterdefrostheaterhasbeenturned
on).
• Defrostterminatoropensat55°F(13°C)andcloses
at20°F(-7°C).
• Compressorruntimebetweendefrost(CRTD)will
beoneof3valuesundernormaloperation:CRTD1
(8hours)orCRTD2(12hours)orCRTD3(16
hours).
Ifdefrostlengthislow(DT-LOdefinedas21
minutes)indicatingsmallfrostload,CRTDfornext
defrostcycleisadvancedtonextlevel.
Ifdefrostlengthishigh(DI-HIdefinedas24
minutes)indicatinglargefrostload,CRTDfornext
defrostcycleisloweredtonextlevel.
Ifdefrostlengthisbetween21and24minutes,
CRTDfornextdefrostcycleremainsthesame.
InitialvalueatpowerupCRTD0is4hours.
• VacationModeCRTDequals96hours.Vacation
ModeCRTDisinterruptedwithdooropenings.
Defrostintervalwillrevertbacktointervalbefore
VacationMode.Threethingsmustoccurtoreach
VacationModeCRTD:
1)DefrostintervalmustbeCRTD3(16hours).
2)Bothrefrigeratorandfreezerdoorsmusthave
remained closed since last defrost cycle.
3)Defrostthermostatmusthaveopenedinless
than21minutesduring lastdefrostcycle.
• Sixminutedwelltime occurs after defrost
terminatoropensbeforecompressorandcondenser
fanmotorwilloperate.Tenminutedwelltime
occursafterdefrostterminatoropensbefore
evaporatorfanmotorwilloperate.Dwelltimecanbe
bypassedbydisconnectingpowertotheunitfor30
seconds.
• ConventionaldefrostcanbeselectedinProgram
ModeB.

February1998 13 12074208
Program Mode
Accessing Program Mode
Twoprogrammingmodesareavailable.ModeAallows
readingrefrigeratorandfreezerthermistor
temperatures.ModeBisusedforallother
programmablefunctions.
1. Openrefrigeratordoor.
2. Press DisplayOn pad.
3. Press *pad.
4. Pressthefollowingsequenceofpadswithin6
seconds: MaxRef,MaxFrz,MaxRef,MaxFrz.
5. Whenaccess is granted, tone will sound three time
andcontrolwillbeinProgramModeA.Unmarked
indicatorlightwillilluminate.
6. ToggletoProgramModeBbypressing DisplayOn
pad.Unmarkedindicatorlightisoff.
EEPROM Update in Control Memory
EEPROMispermanentprogrammablememoryofthe
controlpanel.
• Entrytone,door audioalarmandstatusarestored
inEEPROMaftercontrolpanelisdeactivated.
• InformationstoredinEEPROMmemoryisnot
affectedbypowerloss.
Mode A Functions
Reading Temperature Display
Temperaturedisplaywillshowthermistortemperature
inbinarycodeddecimalformat(BCD).Indicatorlights1
through4representthetensdigitwith1 being themost
significantbit.Indicatorlights5through8represent
onesdigit with 5being the most significant bit. Positive
andnegativeareshownbyindicatorlight9;lightglows
toshownegativevalue
.
Indicator
1
2
3
4
5
6
7
8
Valuewhen
8
4
2
1
8
4
2
1
Coldest +/-
Degrees F.3 6
Add together all lit indicators
1through4according to their
values to obtain ten's column
digit. Example if 3 and 4 are lit
the tens column total 3 (2 + 1
= 3)
Add together all lit indicators 5
through 8 according to their
values to get one's column
digit. Example if 6 and 7 are lit
the one column total6 (4 +2
= 6). The example temperature
is 36º F. w ith coldest indicator
not lit.
Value
Freezer Thermistor Temperature
1. Choosefreezerthermistortemperaturedisplayby
pressing FreezerTemp pad.
2. Freezerthermistortemperaturedisplays.
Refrigerator Thermistor Temperature
1. ChooseRefrigeratorthermistortemperaturedisplay
bypressing RefTemp pad.
2. Refrigeratorthermistortemperaturedisplays.
Mode B Functions
AutomaticKeyboard Function
Activateanddeactivatekeyboardbytoggling
DisplayOff pad.Ifhightemperatureindicatorglows,
keyboardwilldisableafter10minutes.Ifhigh
temperatureindicatorisoff,keyboardisalways
enabled.DONOTLEAVEKEYBOARDINENABLED
MODEAFTERPROGRAMMINGISCOMPLETE.
Door Alarm Delay
1. Press AlarmOff pad.Dooropenindicatorwillglow.
Onetemperatureindicatorshouldglowindicating
presentdelaysettinginminutes(indicator1means
1 minute, 2 means 2 minutes, etc.) Default delay is
3 minutes.
2. Press Warmer padtodecrease delayby1 minute.
3. Press Colder padtoincreasedelayby1minute.
Max Ref Run Time Duration
1. Press MaxRef pad.MaxReflightwillglow.One
temperatureindicatorshouldglowindicating
presentMaxRefruntimedurationin2hour
increments(indicator1means2hours,2means 4
hours,etc.)Defaultdelayis10hours.
2. Press Warmer padtodecreaseMaxRefdurationby
2hours.
3. Press Colder padtoincreaseMaxRefdurationby2
hours.
Max Frz Run Time Duration
1. Press MaxFrz pad.Max Frzlight will glow.One
temperatureindicatorshouldglowindicating
presentMaxFrzruntimedurationin4hour
increments(indicator1means4hours,2means 8
hours,etc.)Defaultdelayis24hours.
2. Press Warmer padto decreaseMaxFrzdurationby
4hours.
3. Press Colder padtoincreaseMaxFrzdurationby4
hours.

12074208 14 February1998
Temperature Offset Calibration
Offsetamountadjuststemperaturesforrefrigeratorcut-
insandcut-outsby the amount ofoffset.Thechart
belowshowstheindicatorandtheamountofoffsetfrom
thefactorydefaultsetting.
INDICATOR OFFSET
1+8
2+6
3+4
4+2
5 0
6-2
7-4
8-6
Coldest -8
• SettingRefrigeratorTemperatureOffset
Press RefTemp pad.Refrigeratorindicatorandone
indicatorwillglow.Press Warmer padtomove
offsettothenextwarmersetting.Press Colder pad
tomove offset to the nextcolder setting.Factory
defaultrefrigeratoroffsetis+2.
• SettingFreezerTemperatureOffset
Press FreezerTemp pad.Freezertemperature
indicatorandoneindicatorwillglow.PressWarmer
padtomoveoffsettothenextwarmersetting.
PressColderpadtomoveoffsettothenextcolder
setting.Factorydefaultfreezeroffsetis0.
Defrost Mode Selection
Toggle*padtoselectadaptiveorconventionaldefrost
mode.Vacationindicatorglowswhenadaptivedefrost
hasbeenselected.Ifvacationindicatorisoff,
conventionaldefrostisselected.Conventionaldefrost
uses8hourCRTDvalue.
ForcedDefrost
Defrostcanbeforcedtostartbypressingandholding
the AlarmOff pad for 3 seconds. Programchanges will
besavedpermanentlyinEEPROMandprogrammode
willexit toRun Mode.
ForcedPulldown (Compressor Start)
Compressorstartcanbeforcedbypressingand
holding MaxFrz padfor3seconds.Programchanges
willbesavedpermanentlyinEEPROM.Compressor,
evaporatorfan,damperheater,andcondenserfanwill
comeon.
Program Mode
Exiting Program Mode
Press DisplayOn padfor3seconds toexitProgram
Mode.Tonewillsoundthreetimes.Changesmadein
ProgramModewillbepermanentlysavedinEEPROM.
Note: Ifnopadispressedfor10minutes,Program
Modewillbeautomaticallyexited.However,no
changeswillbesavedifProgramModeexits
automatically.

February1998 15 12074208
3. Ifterminal7onhighvoltageboardchangeswith
openingandclosingofdoor,orangewireinlow
voltageharnessisbroken(checkforcontinuity
betweenpin7onhighvoltageboardandpin10on
lowvoltageboard)orlowvoltageboardneeds
replacing.
1. CheckforlinevoltageonterminalE8onhigh
voltageboard.Withfreezerdooropen,reading
shouldbe115VAC.Withdoorclosed,reading
shouldbeapproximately0VAC.Ifvoltagedoesnot
changewith light switchand light switch is turning
lightoffandon,violet/whitewireisbrokenbetween
switchandhighvoltageboard.
2. Checkforvoltageonpin7onpinconnectorofhigh
voltageboard.Outputvoltageshouldtogglewith
togglingof light switch.If itdoes nottoggle,high
voltageboardneedsreplacing.
3. Ifvoltageonpin7onpinconnectoronhighvoltage
boardchangeswithopeningandclosingofdoor,
orangewireinlowvoltageharnessisbroken(check
forcontinuitybetweenpin7onhighvoltagepin
connectorandpin10onlowvoltageboard)orlow
voltageboardneedsreplacing.
Electronic Testing
Electronic Testing Mode
ForcedDefrostStart
1. Press DisplayOn padtoactivatecontrolpanel.
2. Simultaneouslypressandhold MaxRef and
DisplayOff padsfor3seconds.
ForcedCompressorStart
1. Press DisplayOn padtoactivatecontrolpanel.
2. Simultaneouslypressandhold MaxFrz padand
DisplayOff padfor3seconds.
OpenThermistorDetect
Alarmsoundsandfreezerorrefrigeratorindicatorlight
showsandtemperatureindicators4through7willturn
oninsequenceifeitherthermistorcircuitopens.Refer
toTemperatureControlOperationSectionand
ElectronicTestingSection.
1. Press AlarmOff pad to turn off alarm.
2. Alarmwillretestfornormaloperation.Ifcondition
hasnotbeencorrected,alarmwillsoundagain.
EvaporatorFanSuppression
Theevaporatorfanwillturnoffeverytimeeither
refrigeratororfreezerdoorisopen.
Totest ifthis functionis operating:
1. Performforcedpulldownprocedureasnotedabove
–evaporatorfanshouldbeon.
2. Opentherefrigeratororfreezerdoor–thefanshould
turnoff.
3. Pushthelightswitchoff–theevaporatorfanshould
start.
Iffandoesnottoggleoffandonwhenrefrigeratorlight
switchisturnedoffandonandithasbeendetermined
evaporatorfanmotorisoperational,performfollowing
teststodeterminefailure:
1. CheckforlinevoltageonterminalE7onhigh
voltageboard.Withrefrigeratordooropen
(refrigeratorlightON) readingshouldbe115VAC.
Withrefrigeratordoorclosed(refrigeratorlightOFF)
readingshouldbeapproximately0VAC.
Ifvoltagedoesnotchangewithlightswitchand
lightswitch isturninglightoffandon,red/whitewire
isbrokenbetweenswitchandhighvoltageboard.
2. CheckforvoltageonterminalE7onhighvoltage
board.Outputvoltageshouldtogglewithtogglingof
lightswitch.Ifoutputvoltagedoesnottoggle,high
voltageboardneedsreplacing.
DANGER
HighVoltage
DANGER
HighVoltage

12074208 16 February1998
Electronic Functional Description
Toavoidelectricalshock which can causeseverepersonalinjuryordeath,disconnectpowertorefrigerator
usingpowerswitch beforeservicing. Wiresremovedduringdisassemblymustbereplacedonproper
terminalstoinsurecorrectearthingandpolarization.Afterservicing,reconnectpower using power switch.
WARNING
100-298-03 RE F-A MP- 03 SN. 2307 10627301
9309
E3
K1
Ground
Line Volta
g
e (L1)
Neutral (L2)
Freezer Door Open
Refri
g
erator Door
Open
Defrost Heater
Defrost Heater Rela
y
Defrost Terminator
Comp./Cond. Fan Power Switch
Comp./Cond. Fan Rela
y
Evaporator Fan
Evaporator Fan Rela
y
DC Fans
12 Pin Connector
Capacitor
Transformer

February1998 17 12074208
Electronic Functional Description
Toavoidelectricalshock which can causeseverepersonalinjuryordeath,disconnectpowertorefrigerator
usingpowerswitch beforeservicing. Wiresremovedduringdisassemblymustbereplacedonproper
terminalstoinsurecorrectearthingandpolarization.Afterservicing,reconnectpower using power switch.
WARNING
Refrigeration and Defrost Component Checks Made at High Voltage Board
Lowvoltageboardinput W1 to D11 approximately -25VDC
Highvoltageboardinput E10to E9(Neutral) or ground approximately 120VAC
Compressor/condenserfanmotor “ON” = E4 to E9 (Neutral) ground approximately 120VAC
“OFF”= E4 to E9 (Neutral) or ground
Compressor/condenserfanmotor “CLOSED”=R7toground approximately -11VDC
relay “OPEN”=R7toground approximately -25VDC
Evaporatorfanmotorrelay “CLOSED”=R8toground approximately -11VDC
“OPEN”=R8toground -25 VDC
Evaporatorfanmotor “ON”=E2toE9(Neutral)orground approximately 120VAC
“OFF”=E2toE9(Neutral)orground 0 VAC
Defrostheater “ON”=E6toE9(Neutral)orground approximately 120VAC
“OFF”=E6toE9(Neutral)orground 0 VAC
Defrostheaterrelay “CLOSED”=R9toground approximately -11VDC
“OPEN”=R9toground approximately -25VDC
Defrostterminator “CLOSED”=E5toE9(Neutral)orground approximately 120VAC
“OPEN”=E5toE9(Neutral)orground 0 VAC
DCfanoutputvoltagefrom “ON”=E1toground approximately -25VDC
highvoltageboardtofreshfoodfan “OFF”=E1toground 0 VDC
orcondensateevaporationfan
DCfaninputvoltage “ON”=R10toground approximately -11VDC
Signaltohighvoltageboardfrom “OFF”=R10toground approximately -25VDC
lowvoltageboardfor
freshfoodfanandforconsendate
evaporationfan
Filamentvoltageat pins11 and 12= lessthan 5 VAC

12074208 18 February1998
Wiring Schematic
Toavoidelectricalshock which can causeseverepersonalinjuryordeath,disconnectpowertorefrigerator
usingpowerswitch beforeservicing. Wiresremovedduringdisassemblymustbereplacedonproper
terminalstoinsurecorrectearthingandpolarization.Afterservicing,reconnectpower using power switch.
WARNING
DANGER
HighVoltage
12405801 PRINTED IN U.S.A.

February1998 19 12074208
Wiring Diagram
WARNING
Toavoidelectricalshock which can causeseverepersonalinjuryordeath,disconnectpowertorefrigerator
usingpowerswitch beforeservicing. Wiresremovedduringdisassemblymustbereplacedonproper
terminalstoinsurecorrectearthingandpolarization.Afterservicing,reconnectpower using power switch.
12045901 PRINTED IN U.S.A.

12074208 20 February1998
Ice Maker
Operation
Thermostatcloseswhentemperaturereaches
17°± 3°F(-8.3°±1.5°C).Currentflowsthrough
thermostattomotor.See“IceMakerWiringDiagram”.
Motorislinkedwithdrivegear.Frommodule,thereare
coppercontactsthat rideon copper stripson backside
ofdrivegear.Asthedrivegearrotates,contactswill
make or break a circuit (tract) to the copper strips to
operateicemaker.
Allcomponentscanbetestedwithoutremovingice
makerormovingrefrigeratorawayfrominstallation.
Removecover.
Testpointsareidentifiedonmodule:
N=Neutralside of line
M = Motor connection
H=HeaterConnection
T=Thermostatconnection
L= L1 sideof line
V=Watervalveconnection
N
M
H
T
L
V
Specifications
Moldheater: 185watts,264ohms
Thermostat: Close17±3°F(-8±1°C)
(bimetal) Opens32°±3°F(0°±1°C)
Waterfill: 140 cc, 7.5 sec.
Motor cycle: Stamped in circuit.
Pluginconnectors.
Onerevolutionofbladestakes
3 minutes plug stall time on ice
(ejectandwaterfill).
Testing Procedures
Verifyicemakerhaspower,shut-offarmisdown,and
freezeriscoldenoughtoclosebimetalthermostat.
• Testpoint L and N willverify120voltstoicemaker
module.
• Testpoints T and H willverifybimetalthermostatis
openorclosed.
• Verify test probes go into test points 1/2 inch
(1.25cm).
1. Short T and H withashunt(insulated14gaugewire
withends stripped back5/8 inch(1.6 cm))torun
motor.Ifmotorruns,replacebimetalthermostat.If
motordoesnotrun,replacemodule.
2. Leavejumperinforhalfofrevolution.Touchheater
mold.Ifheatermoldfeelswarm,heaterisworking
properly.
3. Removejumper.Watervalvewillbeenergizedin
lasthalfofrevolutionifmoldheaterhasnotfailed.
!
Caution
Toavoid icemaker damagedo notshort any
contactstogether other than those specified.