Amber 4224 User manual

4 CHANNEL RADIO RECEIVER MODEL 4224
INSTALLATION MANUAL Page 1
Amber Controls. 3 Gisborne Close, Yoxall, Staffordshire, DE13 8NU England.
el: ++44-1543-732094 [e-mail]
NO E: he model 4224 Receiver operates in conjunction with model 4216 4 Channel key Fob
ransmitter and model 4244 Fork Lift ruck, Rolling Code transmitters.
ACCESS O ERMINALS
Remove the main cover by sliding it off the base in the direction of the aerial.
AN ENNA (AERIAL)
Note that the antenna (aerial) is fixed and is protected by the outer cover moulding. Be careful when
replacing the cover to ensure that the antenna slides back into the protective recess in the cover.
WIRING
14-Way connector
A 12-24V A/C or DC supply should be connected to the two left hand end terminals of the
14-way connector. he supply terminals are not polarity conscious.
Note: he GREEN LED LD1 will illuminate when power is applied.
he relay output terminals are labelled as follows:
NC1 COM1 NO1 NC2 COM2 NO2 NC3 COM3 NO3 NC4 COM4 NO4
he terminal marked NC means NORMALLY CLOSED and refers to the common (COM) terminal.
he terminal marked NO means NORMALLY OPEN and refers to the common (COM) terminal.
he relay’s contacts are isolated volt-free and are isolated from other relay contacts.
Note that each of the relay output terminals respond to the related button of the ransmitter.
(Buttons 1, 2, 3, or 4).
MOUN ING
If the receiver is mounted in a plastic control box, ensure that it is not sited next to devices likely to
emit electrical noise, such as contactors, electronic timers, inverters or other similar devices. he
receiver should not be mounted in a steel control box as the radio signal reception will be very poor
or non-existent. wo screws and plastic plugs are supplied for mounting.

4 CHANNEL RADIO RECEIVER MODEL 4224
INSTALLATION MANUAL Page 2
Amber Controls. 3 Gisborne Close, Yoxall, Staffordshire, DE13 8NU England.
el: ++44-1543-732094 [e-mail]
RELAY OPERA ING MODE SELEC ION
ON OFF TRANSMITTER OR
CASE BUTTON
DIP SWI CH 1 Channel 1 LA CH Channel 1 MOMEN ARY 1
DIP SWI CH 2 Channel 2 LA CH Channel 2 MOMEN ARY 2
DIP SWI CH 3 Channel 3 LA CH Channel 3 MOMEN ARY 3
DIP SWI CH 4 Channel 4 LA CH Channel 4 MOMEN ARY 4
Note that the receiver is shipped with all 4 DIP switches set to OFF for MOMEN ARY operation.
RANSMI ER CODE PROGRAMMING
Up to 30 transmitter codes can be programmed into the receiver’s memory.
Locate the LEARN button which is next to the DIP switches.
1. Press and release the LEARN button
2. he RED LED LD2 will illuminate.
3. Press and release any one of the transmitter buttons.
4. he RED LD2 will turn off.
5. Press and release the same button a second time.
6. he RED LED LD1 will flicker for a few seconds to indicate that the programming is
successful.
RANSMI ER CODE ERASURE
1. Press and HOLD the LEARN button
2. he RED LED LD2 will illuminate for 8 seconds.
3. Release the LEARN button when the LED turns off.
4. he RED LED LD1 will illuminate for 2 seconds to confirm that all codes have been erased.
ADDI IONAL RANSMI ER CODE PROGRAMMING
If one transmitter has already been programmed into the receiver memory then it can be used to
initiate programming of further codes without removing the receiver cover as follows:
1. Using the existing programmed transmitter, press and release both button 1 and button 2
together.
2. hen press button 2. his puts the receiver into a program mode.
3. hen press button 1 of the new transmitter WICE.
4. est the operation of the new transmitter to confirm that the new code has been stored in
memory.

4 CHANNEL RADIO RECEIVER MODEL 4224
INSTALLATION MANUAL Page 3
Amber Controls. 3 Gisborne Close, Yoxall, Staffordshire, DE13 8NU England.
el: ++44-1543-732094 [e-mail]
SPECIFICA ION
Working voltage: 12-24V A/C or DC.
Operating temperature range: -20 to +60 degrees Celsius.
Operating frequency: 433.92 MHz.
ransmitter code type: Rolling code.
Relay load capacity: 240V 3A A/C, 0.5HP. 30V 3A DC.
REV03 - 4-04-2022