AMC VOX-4W User guide

www.amcelettronica.com VOX-4W v. 1.0
VOX-4W
TWO-WAY GSM DIALER WITH ENVIRONMENTAL LISTENING
INSTALLER'S
MANUAL
ENGLISH
DESCRIPTION
Voxout is a two-way integrated dialer with keyboard, equipped with environmental listening and a simulated telephone line.
Its main features are:
. provider test/best gsm signal based on available cells
- credit exhaustion management, with voice alert and/or sms for low credit threshold (programmable threshold)
- sim expiration display (for operators who support the sms service)
- remote control with voice guidance
- local programming from keyboard
- remote programming via sms
- output enabling via ring with confirmation ring
- 5 selectable lines that can be freely programmed as inputs or outputs
- Double State Signal: vocal calls / sms on opening/restoring of the inputs
- 1 local input for reset of calls in progress
- 1 simulated PSTN line with which it is possible to make phonecalls with a standard touch-tone telephone, or connect the dialer to
a wire telephone exchange.
- 12 user codes
- 8 programmable telephone numbers for voice calls and SMS
- 8 programmable telephone numbers for digital transmission of contact ID
- 200 programmable telephone numbers for the remote control function

www.amcelettronica.com VOX-4W v. 1.0
- WALL MOUNT AND CABLING -
The wall mount should be performed using the holes on the rear of the cover (1)
cable routing
fixing holes
fixing holes
knock-out protection
tear

www.amcelettronica.com VOX-4W v. 1.0
- TECHNICAL INDICATIONS OF USING -
IMPORTANT: the equipment, if used like a device for transmission of alarms of a CIE, can be connected only
if:
- the CIE complies to EN 50131-1 and EN 50131-3 (Grade 1)
- the terminals “1,2”, connected to the outputs of a CIE, are programmed as “balanced inputs”, and confi-
gured to send vocal calls/SMS for intrusion and power failure;
- the terminal “3” is configured like “output of type T” (tamper) and connected to an input always active
controlled from the CIE;
- the terminal “4” is configured like “output of type G” (GSM failure) and connected to an input controlled
form the CIE;
- the terminal “5” can be used with a CIE that has the function of “robbery” (in this case the terminal con-
nected to an output of a CIE, must be progammed like “balanced input” and configured to send vocal calls/
SMS for robbery) or with a CIE that allows access at level 3 without the authorization of users at level 2.
NOTE: for CIE with grade upper to 1 and/or when there are 2 or more inputs like robbery, the device of tran-
smission of alarms can not be used (availability in inputs/outputs insufficient).
- INDEX -
PROGRAMMING MENU FROM KEYBOARD - 1 page 03
PROGRAMMING MENU FROM KEYBOARD - 2 page 04
PROGRAMMING MENU FROM KEYBOARD - 3 page 05
USER MENU page 06
VOICE GUIDED MENU page 07
CARD DESCRIPTION - EXAMPLE OF A CONNECTION TO AN EXCHANGE page 08
BEST PROVIDER TEST page 09
SYMBOLS AND DISPLAY VIEWING IN STANDBY page 09
RESET DEFAULT page 10
LED FUNCTIONING LOGIC page 10
PROGRAMMING page 10
MENU OF IN / OUT LINES NAMES page 10
MENU OF IN / OUT LINES TYPE page 10
MENU OF TELEPHONE NUMBERS page 11
RESET OF CALLS / SMS page 11
MENU OF VOICE CALLS page 11
MENU OF SMS MESSAGES page 12
MENU OF INPUTS page 13
MENU OF OUTPUTS page 13
MENU OF USER CODES page 14
SIM CREDIT INFO MENU page 15
TEST MENU page 15
MENU OF VARIOUS PARAMETERS page 16
PROGRAMMING AND MANAGEMENT FROM SMS MESSAGES page 17
TECHNICAL SPECIFICATIONS page 20

4
www.amcelettronica.com VOX-4W v. 1.0
PROGRAMMING MENU FROM KEYBOARD - 1
PERSONAL
CODE
Cod. TECHNICAL
000000
Cod. USER
111111
E01 opening of Input 1
E02 opening of Input 2
E03 opening of Input 3
E04 opening of Input 4
E05 opening of Input 5
E06 closing of Input 1
E07 closing of Input 2
E08 closing of Input 3
E09 closing of Input 4
E10 closing of Input 5
E11 Tamper of Input 01
E12 Tamper of Input 02
E13 Tamper of Input 03
E14 Tamper of Input 04
E15 Tamper of Input 05
E16 Life Test
E17 GSM OFF 1min
E18 Tampering
E19 Low Credit
TELEPHONE
NUMBER MENU
TEL. NUMBER from [ 01 ] to [ 08 ]
VOICE CALL
MENU
E01 –opening L01
V-PLAY X-REC
VOICE MESSAGE
Listen/Record
VOICE MESSAGES
Assign telephones
Answ. Wait 50
Time of Attempts 15
Num. of attempts 3
Msg. repet. 2
SMS MESSAGE
MENU
SMS MENU
Edit test SMS L1 opening
Insert text……..
SMS MENU
Assig telephones E01 / tel [phone]
SMS/ tel [phone]
echo
This parameter send all the SMS received by the
dialer to the programmed numbers
Time in sec. of the duration
Of the outgoing calls
CANCEL (x) TO RECORD
ENTER (V) TO LISTEN AGAIN
Time in sec. between one attempt
and the next call attempt
Call attempts made in case
phonecalls have not been
successful
Number of repetitions of the
voice message
EXT NUMBER from [001] to [200]
The phone book with 200 numbers allows the user to enable
output 5, by sending out onlyone ring to the dialer.
IMPORTANT: always type in the phone number with the
international country code (+39 for Italy)
IN/OUT LINES
MENU IN/OUT LINES
NAME
IN/OUT LINES
TYPE
LINE NUM. [01]
LINE 01
OPT/TEL. 01 to 08 ABC
SISTEM NAME
V-PLAY X-REC
E01 / tel [phone]
*- play
INPUTS
MENU
Enter (✔) = to change
Rh arrow to change input
Up arrow to choose function
- = not programmed input
A = Alarm with reset input closed
H = input 24h always enabled
Function [ 01 ] Line 01
H----
Associate Outputs Enter (✔) = to change
1- 5 n° associated output
- = output unassociated
Enter (✔) = to change
Rh arrow to change input
Up arrow to choose function
- = not programmed
O = NO
C = NC
B = balanced
U = output
[ 01 ] Line 01
O - - - -
[ 01 ] Line 01
inàOut 2 - - - -
Line 01 Msg
Linea 02 Msg
Linea 03 Msg
Linea 04 Msg
Linea 05 Msg
SYSTEM Name
Event
A = answer confirm with #
B = direct access to vocal menù
C = reset call cycle

5
www.amcelettronica.com VOX-4W v. 1.0
PROGRAMMING MENU FROM KEYBOARD - 2
This parameter allows the user to enable/disable the
outputs by sending out a ring from a programmed
remote telephone. If the output duration is 0, output is
stable, therefore enable/disable step by step. If other
than 0, it becomes a pulse output.
IMPORTANT: always type in the telephone number
with the international country code (+39 for Italy).
The output must have function P
Enter (✔) = to change
Rh arrow to change output
Up arrow to choose function
- = not programmed
A = Is enabled with input associated with RES
closed low
H = Is enabled with associated input (always, also
with RES open)
T = Tamper alarm
U = Associated to a user code (local and remote)
P = Can be piloted from remote without user code
G = gsm problem (no GSM for 60'’)
I = Input in standby
C = Low credit
R = ring
M = Master (key 6)
1 - 5 = User enabled only to enable/disable the
associated output (the output must have function U)
OUTPUT
MENU Function
Pulse duration
Associate Telephones
USER CODE
MENU User types [ 01 ] User Nr 01
M
Program Codes
CODE: User Nr xx
111111 (default UT01)
Reset Calls
999999 (default)
SIM Code
0000 (default)
Tel [phone]
Prog ●●●●●●●●
Program with □ the numbers enabled to the
operations on the dialer.
Warning: to ensure proper operation, the
telephone numbers in the phone book must
always be preceded by +39
Program the desired number for the manual
reset of the call que (it is sufficient to insert even
just one digit).
[ 01 ] Line 01
H - - - -
L1 O / tel [phone]
[ 01 ] Line 01
Sec. 15

6
www.amcelettronica.com VOX-4W v. 1.0
PROGRAMMING MENU FROM KEYBOARD - 3
SIM CREDIT INFO
MENU
Tel. TIM
40916
Tel. VODAFONE
404
Tel. wind
4155
Tel. other
TIM Credit
PRE CRE SIN
VODAFONE Credit
WIND Credit
SALDO
OTHER Credit
Credit threshold
[EURO] 3
MENU
VARIOUS
PARAMETERS
Life Test 0
Answ. Ring 3
Event Delay 5
Value expressed in hours
Time in seconds of the inhibition of an
input after a first opening
Board Tamper 0 0 = disabled
1 = enabled
Key Buzzer 0
Accept Calls 1
Pass Ring 0
Language 0
TIM expiration
PRO INFO
Vodafone expiration
WIND expiration
INFO
OTHER expiration
Enable TVWA
SIM expiration
Environment Vol. 8
MENU TEST TEST
Voice call
KEYWORD
ACCESS POINT
Iliad
USER NAME APN
-----
PASSWORD APN
-----

7
www.amcelettronica.com VOX-4W v. 1.0
USER PROGRAMMING MENU
PERSONAL
CODE
ENABLE OUTPUT
D = Disabled
E = Enabled
- = Disabled (specific function assigned)
CHANGE
PERSONAL CODE
CODE: User No. xx
111111
Cod. USER DEFAULT 111111
[ 01 ] Line 01
D----
Key to enable outputs
Key to disable outputs
Attention !
The functions “Medical Aid” (key “arrow left”) and “Fire” (key “arrow right”) are not covered from the
EN 50136-2-1 and are not used from the dialler.
So the two keys are NOT used for these functions.

8
www.amcelettronica.com VOX-4W v. 1.0
VOICE GUIDED MENU
voice guided menu
The vocal menu is reachable by calling the dialler or when the dialler calls. It’s not used for programming but only for remote man-
agement by the user.
When receiving a call, during the listening or at the end of the voal message, it’s possible:
Type in personal code
followed by #
Incorrect personal
code
2 to act on the remote
commands
4 to connect to a
remote system
3 to know the inputs
status
Choose 1 to Enable/Disable Out “1”
Choose 1 to Enable/Disable Out “2”….
Choose 1 to Enable/Disable Out “5”
Wait
Input “name” enabled/disabled
System enabled (reset closed)
System disabled (reset open)
Incorrect
OK
Welcome
Choose 1 to enable
the environmental
listening option
Key 1 = raise volume
Key 2 = lower volume
# to return to the menu
Code
Enable RING output. If a
terminal PHONE is connected,
by lifting the receiver
communication is enabled
- STOP THE CYCLE CALL WITH THE RESET CODE: by pressing the #, digit the code reset and confirm con # (es. #123#), the voice
will say “cycle call terminated”
- ENTER IN THE VOCAL MENU:ENTRARE NEL MENU’ VOCALE: by pressing the #, digit the user code and confirm con #. It will
be possible to select one of the four voice of the vocal menu.

9
www.amcelettronica.com VOX-4W v. 1.0
CARD DESCRIPTION - EXAMPLE OF A CONNECTION TO AN EXCHANGE
Out1= no 220V
Note: in the example shown in the figure, the dialer is powered by fixed charges from the exchange, the free exchange of the alarm
relay is connected to input 1, the OPEN-COLLECTOR 1 output is configured as the absence of an electrical netwrok and is connected
to input 2.
SUPPLY + - = power supply 13.8Vcc
L 1-2-3-4-5 = Lines inputs / outputs -- Configured like Inputs, refer to NEGATIVE -- Configured like outputs, they
give a NEGATIVE when they are activated
RES = reset of the calls in progress (OPEN TO RESET) -- Referred to NEGATIVE --
PHONE = emulation of a wired telephone line

10
www.amcelettronica.com VOX-4W v. 1.0
SYMBOLS AND DISPLAY VIEWING IN STANDBY
FW:1.00
SIM: 11/12/2012
iTIM
1 4 532
Input icon
Output icon
When flashing, indicates input/outoput not in standby
2Indicates input/output in standby
1
€ 10.92
By pressing the CANC(X) key, it moves from standby
screen to SIM credit/expiration screen
The value of credit is updated automatically every
time that the dialler makes a call or sends a SMS.
It’s possible to request the credit of the SIM also by
pressing ENTER (✔) from this screen.
Note: in the screen that concerns the credit and the sim’s expiration, if question marks appears instead of the data,
the information is not available at the moment. If “dots” appear instead, the system is updating the information
with the provider.
By pressing the CANC (X) key again, you will shift to the display (if available) of the entire SMS received from the
Provider
NOTE: The availability of residual credit value is closely related to the Provider of the GSM network that can pro-
vide this service or not
BEST PROVIDER TEST
Powering the dialer with an antenna wire inserted and without SIM, an analysis will be made of the signals and of the providers
present on site, and the provider with the best signal will be indicated.
The display altenrates the 2 following screens.
1 4 532
SIM RECOMMENDED
1 4 532
iTIM
Once you’ve defined the provider,remove power supply and insert the SIM in the dialer (the SIM is unlocked with the PIN number).
Power the system again, and wait for the signal and the mobile phone operator to appear on the display, as shown in the example
of the following screen: