Amcrest AC-2 User manual

Quick
Start Guide
Connection & Installation
This section provides information about
pairing the handset with the camera.
Once powered on, a battery icon with a lightning bolt
will display on the upper right-hand of the screen. This
indicates the handset is charging. When the handset is
completely charged, the battery indicator shown on
the screen will be full and you may disconnect it from
the charging cable as desired.
Powering on the Camera
❶ Connect the included power
adapter to a wall outlet.
❷Connect the camera to the
power adapter.
❸Slide the ON/OFF switch to
the ON position.
Powering on the Handset
❶ Connect the included
power adapter to a wall outlet.
❷Connect the handset to
the power adapter.
❸Press and hold the power
button until the handset
powers on.
On/O
Press and Hold to Speak
Configuration Settings
Tilt Camera Up
Tilt Camera Down
Pan Camera Right
Pan Camera Left
Indicates if the device is
powered on or o.
Indicates the status of the
connected cameras. When lit
indicates there is no link.
Display
Push to Talk
Menu
Tilt Up
Tilt Down
Pan Right
Pan Left
Power
Link
Icon Description Options
Handset Button Menu
Pairing your Handset & Camera
By default, the camera and the handset comes paired
and should be ready to use, However, If for any
reason pairing needs to be reestablished between the
handset and the camera, please Follow these
instructions:
❶ Within the handset menu please navigate to the
setting icon
❷Next, navigate to "Add" and press the button
located between the standby and buttons
on the handset face.
❸Now, select a channel and press to start the
pairing process.
❹Located under the camera, press and hold the
button while the camera is powered on. If the pairing
process was completed within the allotted time, you
should see an image captured by the camera unit.
Please note that the handset will only pair
within 15 seconds. If the camera does not pair
within this time you will need to begin the
process again.
!

5 Levels
5 Levels
On/OFF
5 Lullabies, All
1 Min, 3 Min, 4 Min
Del, Add, View, Scan
Adjust Voice Detection
Sensitivity
1-36 °C / 34-97 °F
Volume
Screen
Brightness
Night Light
Lullaby Music
Sleep Mode Delay
Camera Options
VOX
Voice Detection
Sensitivity
Current Camera
Unit Temperature
Icon Description Options
Menu Icons Overview
On/O
Confirm Selections
Activate Alternative
Function
Turn Volume Up
Turn Volume Down
Enable/Disable
Scan Between Cameras
Feeds
Power
OK
Alternative
Function
Volume Up
Volume Down
Zoom
Camera Scan
Icon Description Options
Alternative Function (Fn) Icons
Device does not turn on:
› Confirm the camera and monitor unit are both ON (check
Power LED indicator).
› Check that both handset and camera units are charged or
plugged into a charger.
› Battery may be depleted and may need to be recharged or
replaced.
› Check that power adapters are connected correctly.
"Out of Range" displaying on handset unit:
› Move the handset closer to the camera unit.
› Register the camera to the handset unit.
› Reset both units by disconnecting them from battery and
electrical power. Wait about 15 seconds then reconnect and pair.
› Large metallic objects including mirrors, doors, refrigerators,
fillings cabinets, may also block radio signal if it is between the
two units.
› Signal strength may be reduced when in close proximity to
radio or other electrical equipment such as TVs, computers,
phones, fluorescent light, or dimmer switches.
› Use of 2.4Hz product such as WiFi routers, Bluetooth
systems, or microwave ovens may cause interference. Keep
camera and handset units at least 5ft from these items or turn
them o.
Reception Interference:
› The camera and handset units may be too far apart. Move
the handset unit closer to the camera unit.
› The battery power may be too low.
› Check for interference from other electronic devices.
› Handset and camera unit may be too close in proximity to
large metallic objects causing interference.
› Use of 2.4Hz product such as WiFi routers, Bluetooth
systems, or microwave ovens may cause interference. Keep
camera and handset units at least 5ft from these items or turn
them o.
High pitched noise from handset unit:
› Increase the distance between the handset and camera unit.
› Volume may be too high. Reduce the volume on the handset
unit.
› Camera unit may be too far from the handset unit. Move the
camera unit closer to the handset unit.
› Make sure camera and handset units are placed away from
other electrical equipment, such as television, computer, or
phone.
Troubleshooting
For access to the quick start guide and other
support information, go to
www.Amcrest.com/babycam