Amerec R30K User manual

R30K ON/OFF CONTROL
FOR USE WITHAMEREC
AK STEAM GENERATORS
SAVE THIS MANUAL
FORTHESAFETYOFYOUANDYOUR FAMILYPLEASEREADTHEWARNINGSTO
THE RIGHTAND ALLINSTRUCTIONS BEFORE USING YOUR STEAMBATH.
POST "WARNING" LABEL OUTSIDE STEAMBATH FOR SAFETY WARNINGS. RE-
QUIREDPOSTINGONDOOROFSTEAMROOMORADJACENTTODOORFORALL
COMMERCIAL INSTALLATIONS.
ThankyouforpurchasingyournewAMERECsteamgenerator.Ifwecanbeofanyassistancedonothesitate
to call our Service Department at 1-800-363-0251 or 1-425-951-1120.
TheR30Kcontroldoesnotprovideautomatictemperaturecontrol.Usetheon/offbuttontocontrolthe
temperature as desired by turning the steam bath on and off as needed.
Note:theR30Kmay be used as an extraswitchwhena temperature regulating K60 and/or KT60
control is installed. Contact Technical support for further information.
1. Ensure that both the power circuit and water supply to the generator are ON.
2. To activate the steam, press the R30K control's On/Off switch. In 10 to 20 minutes the room
should be comfortable enough to begin taking a steam bath. The unit will turn off automati-
cally in 30 minutes.
3. Remove clothing and jewelry.
4. Enter the steam room and close the door to prevent steam from escaping.
5. Relax and enjoy the warm steam releasing tense muscles and refreshing the entire body. The
average time spent taking a steam bath is approximately 10 minutes
6. Pressing the control while the steam generator is operating will shut it off.
7. If your steam room has a shower, a pleasant experience can be achieved by taking a warm
shower while in the steam. You will find the contrast from water to steam quite invigorating.
SECTION 1: OPERATION OF YOUR R30K AND AMEREC GENERATOR
R30K Control Owners Manual
AK STEAM GENERATOR
R30K
4209-38 04/25/17 Technical Support: 1-425-951-1120 1-800-363-0251 [email protected]
WARNING
Electrical grounding is required
on all Steam Generators.
All electrical supplies should be
disconnected when servicing a
Steam Generator.
All wiring must be installed by a
licensed electrical contractor in
accordance with local and
national codes.
All plumbing must be installed
by a licensed plumber in
accordance with all applicable
local and national codes.
Steamers are for indoor use only.
Steamers are not for
space-heating purposes.
Be certain that steam bath
enclosures are properly sealed
to avoid water damage from
escaping steam. It is
recommended that 100%
silicone caulk be used to seal
all pipes and fittings. Steam
must be prevented from
escaping into the wall cavity.
Never shut off the water to an
appliance that is in use.
Electric Shock Hazard
High Voltage exists within this equipment.
There are no user serviceable parts
in this equipment.
REDUCE THE RISK OF
1. Exit immediately if uncomfortable, dizzy or sleepy. Staying too long in
a heated area is capable of causing overheating.
REDUCE THE RISK OF
Use care when entering or exiting the steam room, floor may be slippery.
NOTE: For additional safety instructions, see owner's manual.
CAUTION!
Do not contact steam head. Stay at least 12" away
from hot steam escaping from the steam outlet.
OVERHEATING AND SCALDING
2. Supervise children at all times.
3. Check with a doctor before use if pregnant, diabetic, in poor health or
under medical care.
4. Breathing heated air in conjunction with consumption of alcohol, drugs
or medication is capable of causing unconsciousness.
SLIPPING AND FALL INJURY
WARNING
4110-79
05-21-07

page 2
R30K Control Owners Manual
4209-38 04/25/17 Technical Support: 1-425-951-1120 1-800-363-0251 [email protected]
IMPORTANT SAFETY INSTRUCTIONS
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. WARNING - To reduce the risk of injury, do not permit children to use this product unless they
are closely supervised at all times.
3. WARNING - To reduce the risk of injury:
a. The wet surfaces of steam enclosures may be slippery. Use care when entering or leaving.
b. The steam head is hot. Do not touch the steam head and avoid the steam near the steam head.
c. Prolonged use of the steam system can raise excessively the internal human body temperature
and impair the body’s ability to regulate its internal temperature (hyperthermia). Limit your use
of steam to 10 - 15 minutes until you are certain of your body’s reaction.
d. Excessive temperatures have a high potential for causing fetal damage during the early months
of pregnancy. Pregnant or possibly pregnant women should consult a physician regarding correct
exposure.
e. Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory
system problems, or diabetes should consult a physician before using a steambath.
f. Persons using medication should consult a physician before using a steambath since some medi-
cation may induce drowsiness while other medications may aff ect heart rate, blood pressure and
circulation.
4. WARNING - Hyperthermia occurs when the internal temperature of the body reaches a level several
degrees above the normal body temperature of 98.6 °F (37°C). The symptoms of hyperthermia include
an increase in the internal temperature of the body, dizziness, lethargy, drowsiness and fainting. The
eff ect of hyperthermia include:
a. Failure to perceive heat:
b. Failure to recognize the need to exit the steambath:
c. Unawareness of impending risk:
d. Fetal damage in pregnant women:
e. Physical inability to exit the steambath: and
f. Unconsciousness.
WARNING - The use of alcohol, drugs or medication can greatly increase the risk of hyperthermia.
SAVE THESE INSTRUCTIONS

page 3
R30K Control Owners Manual
4209-38 04/25/17 Technical Support: 1-425-951-1120 1-800-363-0251 [email protected]
The R30K low voltage control can be mounted directly to a fi nished wall either inside or outside the steam room. The
R30K does not control the temperature in the steam room.
1. Use a 1-1/2” (36 mm) hole saw to drill a hole in the fi nished steam room wall where the control is to be mounted (the
control cable should already be roughed-in to this location).
2. Locate the control cable, pull it out through the mounting hole and plug it into the connector on the back of the control
board, inside the housing.
3. Run a bead of 100% silicone caulk around the perimeter on the back of the control housing. Insert the control into the
wall cavity. Tape the control in place until the silicone has set.
4. Route the R30K control's cable to the steamer circuit board and plug it in to the S30B jack (top edge of the circuit board
next to the S30A terminal block).
SECTION 2: INSTALLATION OF THE R30K: 2017 and later AK Generators
The steam generator, steam head, fi ttings and plumbing connections should be inspected at least annually for water leaks
and damage.
The AK steam generator is supplied with a drain valve for fl ushing sediments from the generator tank. This procedure
should be scheduled monthly or more often depending on local water conditions and steam bath usage.
FLUSHING PROCEDURE
1. The generator should be cool.
2. Turn control on.
3. Open the drain valve.
4. The unit will drain without heating the water.
5. Allow the water to run 10 minutes.
6. Close the drain valve
SECTION 3: MAINTENANCE OF THE AK SERIES
W-D COM
DRAINWATER
SVC
S30B
J4
S30A S60 A S60 B
123
HR
L
G1 G2
AK IN
R30K
1-1/2" (36 mm) HOLE
SILICONE
BACKSIDE
New model AK generators have their circuit boards mounted on the back panel of the generators. Earlier AK and 3K gen-
erators have their circuit boards mounted on the generator's shelf. All operations of both versions are otherwise identical.
For installation in an older steam generator, install the R30K same as in steps 1 - 3 in the new AK Instructions above then"
4. Route the R30K control's cable to the steamer circuit board and plug it in to the S30B jack (near center on the right
end of the circuit board).
SECTION 2: INSTALLATION OF THE R30K: AK & 3K Generators Built Before March, 2017

page 4
R30K Control Owners Manual
4209-38 04/25/17 Technical Support: 1-425-951-1120 1-800-363-0251 [email protected]
17683 128th Place NE, Bldg C
Woodinville, WA 98071 USA
Phone [phone]
1-800-363-0251
email [email protected]
The Troubleshooting Guide below is meant as a general aid only. There are no user serviceable parts in the generator.
All repairs should be performed by a qualifi ed service person. For additional assistance or to fi nd the factory authorized
service person nearest you, call Technical Support.
SECTION 3: TROUBLESHOOTING GUIDE
SYMPTOMS PROBABLE CAUSES ACTION TO BE TAKEN
Control "ON"
(Control Lighted)
No Steam
No water to generator
or
Control circuit is faulty
or
Generator is faulty
1. Wait at least 10 minutes after turning on control and generator
2. Verify that the water is on
3. Verify that the generator's drain valve is closed
4. If the above steps do not disclose the problem, turn off the
generator's circuit breaker and contact Support
Control "OFF"
(Control light "OFF"
Unit makes steam
Control circuit faulty
or
Generator is faulty
1. Turn off the generator's circuit breaker and contact Support
Water runs out steam head Generator is faulty 1. Turn off the water to the generator's and the generator's circuit
breaker and contact Support