American Cart & Rack GRANITE INDUSTRIES MULTI MOVER XT User manual

67245-75
MULTI MOVER XT
WITH FOLD DOWN REAR WHEELS
INSTRUCTION MANUAL
Revised: JULY 2017

2
CONTENTS
Specs......................................................................3
Parts Diagram ........................................................4
Assembly................................................................5
TOOLS NEEDED
• Needle Nose Pliers
• Box Cutters / Utility Knife
• Wrenches: 1/2” & 3/4”
• Sockets: 1/2” & 3/4”
WARRANTY
3 Year Limited Warranty. Carts, excluding any
finishes, casters and wheels are warranted for three
(3) years from date of original purchase. Casters
and wheels are warranted for 90 days from date of
original purchase. We will repair, without charge,
any defect due to faulty material or workmanship.
These warranties do not cover failures due to
abuse, misuse, improper installation, accidental
damage or when repairs or modifications have been
made or attempted to be made by anyone other
than Granite Industries. Any defective products
that meet warranty specifications and Granite
Industries approval, may be returned to the factory
to be repaired or replaced free of charge. (Granite
Industries will pay to ship replacement item(s) to the
customer; however the customer is responsible for
shipment of products to the factory.) This remedy
is the sole remedy in contact, tort or otherwise,
and Granite Industries is not liable for incidental,
consequential or special damages. These warranties
give you specific legal rights, and you may have
other rights which vary from state to state. Should
you have any questions, contact Granite Industries
(Proof of purchase may be required).
Customer Service
877-447-2648
M-F, 8am - 5pm EST
To view more products from
American Cart & Rack
scan the QR code with your phone
or visit AmericanCartAndRack.com

3
SPECS
Overall Dimensions: W: 30” D: 70” H: 38”
Foot Plate: W: 27” D: 31”
Weight: 134 lbs. Capacity: 1200 lbs.
*Measurements taken on 4 wheels with folding foot plate open

4
ITEM NO QTY PART NO DESCRIPTION
1 1 MI-12-5142 MULTI MOVER XT BODY
2 2 PI-06-0055 CASTER MOUNT
3 4 PI-06-0115 10” WHEEL W/ STEEL OFFSET HUB
4 2 PI-01-0226 1-1/4” COTTER PIN
5 2 PI-01-0043 1/2” HEX BOLT (1-1/4” L) USE 3/4” WRENCH/SOCKET
6 2 PI-01-0121 1/2” NUT USE 3/4” WRENCH/SOCKET
7 8 PI-01-0177 5/16"HEX BOLT (1” L) USE 1/2” WRENCH/SOCKET
8 2 06013 3” HINGE PIN
9 16 PI-01-0206 5/16” WASHER
10 8 PI-01-0017 5/16” NUT USE 1/2” WRENCH/SOCKET
11 1 MI-12-5143 REAR WHEEL ASSEMBLY
12 2 PI-01-0451 3/4” WASHER
13 2 PI-06-0051 10” WHEEL W/ STEEL CENTER HUB
-- 2 PI-01-0100 HEX BOLT 3/8”-16 x 3”
-- 4 PI-01-0030 FLAT WASHER 3/8”
-- 2 PI-01-0037 LOCK WASHER 3/8”
-- 2 PI-01-0072 3/8”WING NUT
PARTS DIAGRAM

5
3
2
COMPONENTS
ITEM NO QTY DESCRIPTION
1 1 Multi Mover XT Cart Body
3 4 10” Wheel w/ Steel Offset Hub
4 2 1-1/4” Cotter Pin
12 2 3/4” Washer
TOOLS
Needle Nose Pliers
Note: All steps are done with the cart facing down as
shows in the photo to the right.
Slide the second wheel onto the axle, this
time making sure the offset side faces
inward. The offset sides of both tires should
be facing each other.
STEP 1: FRONT WHEEL ASSEMBLY
1
Slide the first wheel onto the axle, making
sure the flush side of the hub goes towards
the body of the cart.
Slide the washer onto the axle.
4
Insert the cotter pin and secure it by
bending both ends outward with a
needle nose pliers.
Repeat this process for the other side.

6
3
2
COMPONENTS
ITEM NO QTY DESCRIPTION
5 2 1/2” Hex Bolt
6 2 1/2” Nut (1” L)
8 2 3” Hinge Pin
11 1 Rear Wheel Assembly
TOOLS
3/4” Wrench
3/4” Socket
Insert the bolts through the cart body and
rear axle assembly. Tighten down with a 3/4”
wrench and ratchet.
STEP 2: REAR WHEEL ASSEMBLY
1
Place the rear wheel assembly over the
frame toward the top of the cart. The flat
side should be against the cart body, the
flanges should face up. Insert the snap pins
to help hold it in place.
For heavy duty use, we recommend using a
bolt kit into the rear wheel assembly. Install a
3/8” washer onto the bolt, then insert the bolt
into the rear wheel assembly. Add another 3/8”
washer, then a lock washer.
4
Secure the bolt in place with a wing nut.
Repeat the process for the other side.
TOP OF CART
BOTTOM OF CART

7
3
2
COMPONENTS
ITEM NO QTY DESCRIPTION
2 2 Caster Mount
7 8 5/16” Hex Bolt (1”L)
9 16 5/16” Washer
10 8 5/16” Nut
TOOLS
1/2” Wrench
1/2” Socket
Slide another 5/16” washer onto the
bolt,followed by the lock nut. Tighten each
nut (but not all the way) with a 1/2” wrench
and a 1/2” socket.
STEP 3: INSTALL CASTER MOUNTS
1
Align the caster mount onto the holes.
Place a 5/16” washer onto the 5/16” bolt
and insert the bolt through the rear wheel
assembly and caster mount.
Make any adjustments to the caster mount
to ensure it is on straight. Then finish
tightening down all of the nuts.
Once installed your caster mounts should
look like this.

8
3
2
COMPONENTS
ITEM NO QTY DESCRIPTION
3 2 10” Wheels with steel center hub
TOOLS
3/4” Wrench
3/4” Socket
Insert the bushing through one of the wheel
hubs, then position the caster wheel into the
caster mount.
STEP 4: INSTALL REAR WHEELS
1
Remove the bolt and bushing from the caster
mount using a 3/4” wrench and socket.
Insert the 1/2” bolt and fasten the 1/2” nut
into place using a 3/4” wrench
and 3/4” socket.
Your Multi Mover XT with Rear Wheels
is now fully assembled.