American Dynamics AD32E Manual

8000-1702-02, Rev. B
AD32 SYSTEM
INSTALLATION AND SERVICE
MANUAL

AD32 SYSTEM
INSTALLATION AND SERVICE MANUAL
Copyright 1999
All rights reserved
CSD 08/99
No part of this manual may be reproduced in any form without
written permission from Sensormatic® Electronics Corporation.
8000-1702-02, Rev. B

EQUIPMENT MODIFICATION CAUTION
Equipment changes or modifications not expressly approved by Sensormatic
Electronics Corporation, the party responsible for FCC compliance, could void
the user's authority to operate the equipment and could create a hazardous
condition.
FCC COMPLIANCE
This equipment has been tested and complies with the limits for a Class A digital
device, according to Part 15 of the FCC Rules. These limits provide reasonable
protection against harmful interference when the equipment operates in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy, and, if not installed and used according to these instructions,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference. If this equipment is used in a residential area, users must correct
the interference at their own expense.
WARRANTY DISCLAIMER
Sensormatic Electronics Corporation makes no representation or warranty of the
contents of this manual and disclaims any implied warranties of merchantability
or fitness. Sensormatic Electronics Corporation reserves the right to revise this
manual and change its content without obligation to notify any person of these
revisions.
LIMITED RIGHTS NOTICE
For units of the Department of Defense, all documentation and manuals were
developed at private expense and no part of it was developed using Government
Funds. The restrictions governing the use and disclosure of technical data
marked with this legend are set forth in the definition of "limited rights" in
paragraph (a) (15) of the clause of DFARS 252.227.7013. Unpublished - rights
reserved under the Copyright Laws of the United States.
Sensormatic and the Sensormatic logo are registered trademarks of Sensormatic
Electronics Corporation.
Product names mentioned herein may be trademarks or registered trademarks of
Sensormatic or other companies.

CONTENTS
AD32 SYSTEM
iii
PREFACE....................................................................................................................................................................V
CHAPTER 1 INTRODUCTION ......................................................................................................................... 1-1
SYSTEM OVERVIEW .................................................................................................................................................... 1-3
SYSTEM COMPONENTS................................................................................................................................................ 1-4
AD32 FEATURES AND FUNCTIONS.............................................................................................................................. 1-5
SPECIFICATIONS .......................................................................................................................................................... 1-6
CHAPTER 2 THEORY ....................................................................................................................................... 2-1
CHAPTER 3 INSTALLATION .......................................................................................................................... 3-1
INTRODUCTION ........................................................................................................................................................... 3-3
BEFORE YOU BEGIN ................................................................................................................................................... 3-3
PRE-INSTALLATION CHECKLIST .................................................................................................................................. 3-3
PLANNING THE INSTALLATION .................................................................................................................................... 3-4
SENSORNET NETWORK DESIGN GUIDELINES .............................................................................................................. 3-4
Network Design Considerations............................................................................................................................. 3-4
Remote Dome Considerations................................................................................................................................ 3-6
Attaching SensorLink PC....................................................................................................................................... 3-6
DESIGNING THE SENSORNET NETWORK...................................................................................................................... 3-6
J-Box Required ...................................................................................................................................................... 3-6
J-Box Not Required ............................................................................................................................................... 3-7
VIDEO AND DATA FLOW ............................................................................................................................................. 3-7
SYSTEM INSTALLATION SEQUENCE............................................................................................................................. 3-7
J-Box Required ...................................................................................................................................................... 3-7
J-Box Not Required ............................................................................................................................................... 3-7
Verifying and Unpacking Equipment..................................................................................................................... 3-8
Network Checkout.................................................................................................................................................. 3-8
INSTALLING POWER .................................................................................................................................................... 3-9
INSTALLING DOMES AND CAMERAS ............................................................................................................................ 3-9
Dome Addressing................................................................................................................................................... 3-9
INSTALLING J-BOXES .................................................................................................................................................. 3-9
CONNECTING CABLES—USING J-BOX ........................................................................................................................ 3-9
Attaching Domes to J-Boxes using Composite Cables........................................................................................... 3-9
Attaching J-Boxes to the Video Matrix Switcher................................................................................................. 3-11
CONNECTING CABLES—WITHOUT J-BOX................................................................................................................. 3-13
INSTALLATION PROCEDURES .................................................................................................................................... 3-15
AD32 Video Matrix Switcher (VMS).................................................................................................................. 3-15
Installing Monitors and VCRs.............................................................................................................................. 3-15
Installing Enhanced TOUCH TRACKER Controllers............................................................................................... 3-16
SYSTEM SETUP PROCEDURES ................................................................................................................................... 3-18
Switching Primary and Secondary Functions between Controller Units ..............................................................3-19
Performing SensorNet Ping Test.......................................................................................................................... 3-19
Adjusting Camera V-Phase .................................................................................................................................. 3-19
Resetting a Dome ................................................................................................................................................. 3-20
Changing the Port Setting..................................................................................................................................... 3-20
Viewing System Information................................................................................................................................ 3-20
CHAPTER 4 SERVICE ....................................................................................................................................... 4-1
INTRODUCTION ........................................................................................................................................................... 4-3
Tools and Equipment Required.............................................................................................................................. 4-3
TROUBLESHOOTING PROCEDURES .............................................................................................................................. 4-3
ENHANCED TOUCH TRACKER MAINTENANCE ............................................................................................................ 4-5

AD32 SYSTEM
iv
CHAPTER 5 REFERENCE ................................................................................................................................ 5-1
PARTS LISTS ............................................................................................................................................................... 5-3
Assemblies ............................................................................................................................................................. 5-3
Printed Circuit Boards............................................................................................................................................ 5-4
Install Kits.............................................................................................................................................................. 5-6
DRAWINGS.................................................................................................................................................................. 5-7
APPENDIX A J-BOXES...................................................................................................................................... A-1
SENSORNET 1-POSITION JUNCTION BOX (J-BOX) ...................................................................................................... A-3
Installation Requirements...................................................................................................................................... A-3
Installation Process ............................................................................................................................................... A-3
Specifications ........................................................................................................................................................ A-6
Declarations .......................................................................................................................................................... A-6
SENSORNET 6-POSITION JUNCTION BOX (J-BOX) ...................................................................................................... A-7
Installation Requirements...................................................................................................................................... A-7
Installation Process ............................................................................................................................................... A-7
Specifications ...................................................................................................................................................... A-10
Declarations ........................................................................................................................................................ A-10
APPENDIX B VIDEO MATRIX SWITCHER ALARM AND RELAY CONNECTIONS........................... B-1
ALARM AND RELAY CONNECTIONS ........................................................................................................................... B-3
Connections........................................................................................................................................................... B-3
APPENDIX C ADDING DOMES TO J-BOXES...............................................................................................C-1
ATTACHING ADDITIONAL DOMES TO J-BOX ...............................................................................................................C-3
APPENDIX D ATTACHING SENSORLINK PC ............................................................................................. D-1
ATTACHING SENSORLINK PC TO THE AD32 SYSTEM ................................................................................................ D-3

AD32 SYSTEM
v
Preface
This manual provides the information you need to install a AD32
System. It explains the AD32 System architecture and gives you the
step-by-step tasks for installing the system. It also serves as a
continuing reference for maintaining and troubleshooting the AD32
System.
What’s In This Manual
This manual is organized as follows:
1 Introduction provides a product overview and specifications.
2 Theory of operation is not applicable for this product..
3 Installation provides background and procedures required to
install the system.
4 Service provides troubleshooting procedures for a variety of
problems.
5 Parts Lists and Drawings provides:
•The parts lists for the system’s assemblies, printed circuit
boards, and install kits.
•The assembly, component, and schematic drawings necessary
to install and service the system.
Appendices provide ancillary information necessary to understand,
install, or service the system.
First Time Installations
If you are unfamiliar with the AD32 System, please read the
Introduction chapter first. It contains information important for a
successful installation.
Metric Measurements
Metric is the primary measurement system used in this manual.
Approximate U.S. customary measurements are shown parenthetically
following the metric measurement.

AD32 SYSTEM
vi
Documentation Conventions
This manual uses text in different ways to identify different kinds of
information. Where appropriate, the following styles and symbols are
used.
italics Used for terms that are specific to AD32 and for text
that requires emphasis; also used for document titles.
monospace Used for names of screens and menus, and any
information that appears on a screen.
Note box Indicates a note. Notes provide information that may be
of importance or essential to the proper installation and
operation of the system.
General Information—Calls attention to information
that may be of special importance or essential to the
proper installation and operation of the system.
CAUTION Indicates a caution. A caution contains information
essential to avoid equipment damage. A caution can
pertain to hardware or software.
Caution—Electrostatic Sensitive Device. Use a ground
strap when handling the PC board.
!Indicates a warning. A warning contains information
essential to avoid personal injury or death.
Indicates an electric shock warning. An electric shock
warning contains information essential to avoid
personal injury or death.
Related Documents
•There are other documents that provide information about the
AD32 System. These documents will enhance your understanding
of the system and its application.
•If you are familiar with the installation of the AD32 System, you
can refer to the abbreviated procedures in the AD32 Installation
Instructions (document number 8000-2671-02), which are included
with the system; it contains instructions on how to connect and
configure the Video Matrix Switcher’s inputs and outputs. These
instructions are a supplement to—not a replacement of—the
procedures in this manual.
•The AD32 Operator's Manual (document number 8000-2655-02)
provides detailed information about the features, operation, and
application of the AD32 System. It explains, step-by-step, the tasks
performed when using the system.

AD32 SYSTEM
vii
•The AD32 Quick Reference (document number 8000-2656-02)
provides quick reference information about certain procedures
described in detail in the Operator’s Manual. The Quick reference
is a supplement to—not a replacement of—the information covered
in the Operator’s Manual.
•To connect a VCR to the AD32 System, refer to the documentation
included with the VCR for programming and operating
information.
•To connect a multiplexer to the AD32 System, refer to the
documentation included with the multiplexer for operation and
programming information. The multiplexer can add multiple
display formats and time-lapse or real-time recording functionality
to the AD32 System.
Ordering Documents
For additional copies of the AD32 Installation and Service Manual, or
any other document that will help you use the AD32 System, contact
your local Sensormatic Sales Representative.
The document number for this manual is 8000-1702-02.
Getting Help
If you have a question about the AD32 operation, and you cannot find
the answer in this manual, contact the American Dynamics Customer
Care at 800-507-6268 or Fax at 858-642-2441.

CHAPTER 1
AD32 SYSTEM
1-1
AD32 SYSTEM
CHAPTER 1 INTRODUCTION
In this chapter:
nSystem Overview ......................................................................1-3
Introduces the AD32 System functions and capabilities.
nSystem Components..................................................................1-4
Describes the major components of the AD32 System.
nAD32 Features and Functions ...................................................1-5
Lists the features and functions of the AD32 System.
nSpecifications ............................................................................1-6
Lists the electrical, mechanical, environmental, compatibility, and
regulatory data of the AD32 System.

INTRODUCTION
AD32 SYSTEM
1-2