American Dynamics ADTTE User manual

8000-1658-02, Rev. C AD TOUCH TRACKER Installation Instructions
AD TOUCH TRACKER
Installation Instructions
PARTS REQUIRED
AD TOUCH TRACKER Installation Kit:
0351-0474-04
Description Qty. Part No.
Modular cable assy 4.3m 6003-0047-01
Screw, M2.9x9.5 1 5899-0004-102
Anchor, 4-8x.750 2 2880-0083-01
Screw, #8x1 2 2816-7634-44
Conn, 1x5pos 1 2109-0254-04
Lug, 22-16AWG 3 2141-0002
Cable, 3-cond, 18AWG 5m 6002-0024-01
Interconnect box 1 0300-1000-01
Hood, D-Sub, 9pos, cable 1 2125-0007-02
Conn, D-Sub, plug, hsg, 9pos 2130-0021-01
WARNING Shock Hazard!
Disconnect AC Power to the Switch.
CAUTION Static Sensitive
Components!
Follow proper handling procedures
to prevent component failure.
Installation Procedures
For connections less than or equal to 4m
(14 ft)
Refer to the diagram on page 2.
1. Mount each external interconnect module
(EIM) on a wall or other surface within 3m
(10 ft) of the controller.
2. Connect the power transformer to J3 on
each EIM. Refer to the J3 table on page 2.
3. Wire the DB9 connector to the data cable.
Refer to the DB9 table on page 2.
4. Connect the data cable from J1 on the
TOUCH TRACKER EIM to one of the RS232
ports at the rear panel of the AD Switch.
Refer to the RJ45 table on page 2.
5. Connect the modular cable from J2 on EIM
to the TOUCH TRACKER Controller.
6. Plug each power transformer into a
grounded, 3 wire receptacle.
NOTE: If the keypad and back lighting do not
illuminate when power is applied, unplug
each power transformer and repeat steps 2
through 6.
When all cables are connected, you must set the TOUCH
TRACKER for the appropriate communications protocol.
•If your AD switch does not support keyboard repeat,
enter 200, then press F1 to select Repeat Off. The
AD168 supports this mode.
•If your AD switch supports keyboard repeat, enter
201, then press F1 to select Repeat On. The
AD1650, AD2050, AD2052, AD2150, and AD2350
support this mode.
Repeat On is the default setting for the TOUCH TRACKER.
For connections greater than 4m (14 ft)
This installation requires 2 modular cable assemblies
(Part No. 6003-0047-01), 2 HP0047 AD Terminal
Boxes, and 3-wire, 18 AWG shielded cable. Contact
your sales representative for additional parts.
Refer to the diagram on page 3.
1. Mount each external interconnect module
(EIM) on a wall or other surface within 3m
(10 ft) of the controller.
2. Connect the power transformer to J3 on
each EIM. Refer to the J3 table on page 3.
3. Wire the DB9 connector to the data cable.
Refer to the DB9 table on page 3.
4. Referring to the diagram on page 3, connect
the wires as illustrated to the Terminal
boxes. The shield wire connects to 7 on the
Switch Terminal Box only.
5. Connect one modular cable from J2 on EIM
to the TOUCH TRACKER Controller.
6. Connect the data cable from J1 on the
TOUCH TRACKER EIM to RJ45 on the TOUCH
TRACKER Terminal Box. Refer to the RJ45
table on page 3.
7. Connect remaining modular cable from the
Switch Terminal Box to one of the RS232
ports on the AD Switch.
8. Plug each power transformer into a
grounded, 3 wire receptacle.
NOTE: If the keypad and back lighting do not
illuminate when power is applied, unplug
each transformer and repeat steps 2 through
8.
When all cables are connected, you must set the TOUCH
TRACKER for the appropriate communications protocol.
•If your AD switch does not support keyboard repeat,
enter 200, then press F1 to select Repeat Off. The
AD168 supports this mode.
•If your AD switch supports keyboard repeat, enter
201, then press F1 to select Repeat On. The
AD1650, AD2050, AD2052, AD2150, and AD2350
support this mode.
Repeat On is the default setting for the TOUCH TRACKER.

2 8000-1658-02, Rev. C American Dynamics
AD TOUCH TRACKER
Installation Instructions
FOR CONNECTIONS LESS THAN OR EQUAL TO 4M (14 FT)
J3 Wiring
PIN FUNCTION
24 Vac A
24 Vac B
Ground
2
3
4
4 3 2
EIM
J1
J3
J2
TRANSFORMER
24 Vac A
24 Vac B
Ground
RJ45
RJ45
TOUCH
TRACKER
AD SWITCH
VCR
IN RS232
120V
60Hz
MONITOR
EXPAND QUAD
ALARMS
RJ45
5 4 2
RJ45 Wiring
PIN
COLOR
GREEN
ORANGE
RED
5
4
2
DB9 (M)
5 3 2
DB9 (M) Wiring
PIN FUNCTION
Rx
Ground
Tx
3
2
5
COLOR
GREEN
RED
ORANGE

AD TOUCH TRACKER
Installation Instructions
8000-1658-02. Rev. C TOUCH TRACKER Installation Instructions 3
FOR CONNECTIONS GREATER THAN 4M (14 FT)
8
7
654
1
2
3
8
7
54
1
2
36
12345678
AD SWITCH
VCR
IN RS232
120V
60Hz
MONITOR
EXPAND QUAD
ALARMS
3-wire, 18 awg,
Shielded Cable
TOUCH
TRACKER
Terminal
Box
Switch
Terminal
Box
RJ45
RJ45
RJ45
RJ45
DB9 (M)
5 4 2
5 3 2
TOUCH
TRACKER
DB9 (M) Wiring
RJ45 Wiring
J3 Wiring
PIN FUNCTION
24 Vac A
24 Vac B
Ground
2
3
4
PIN FUNCTION
Rx
Ground
Tx
3
2
5
COLOR
GREEN
RED
ORANGE
4 3 2
PIN
COLOR
GREEN
ORANGE
RED
5
4
2
RJ45
EIM
J1
J3
J2
Shield
TRANSFORMER
24 Vac A
24 Vac B
Ground

AD TOUCH TRACKER
Installation Instructions
4 8000-1658-02, Rev. C American Dynamics
Setting the Baud Rate
The AD TOUCH TRACKER supports four baud rates:
1200, 2400, 4800, and 9600 baud. The default
setting for the baud rate is 1200.
Note:
The TOUCH TRACKER will not operate if you set
the baud rate incorrectly. Be sure that the baud
rates for the TOUCH TRACKER and switch are set to
the same value.
1. Use the number buttons to enter the baud rate
(1200, 2400, 4800 or 9600).
2. Press
F1 (located to left of the LCD).
No prompts appear on the screen to inform you
that the baud rate has been changed.
Tracker Ball Calibration
1. Press the
Calibrate button.
The following message appears on the LCD:
Push Tracker Ball Left
2. Push the Tracker Ball to the left.
The following message appears on the LCD:
Push Tracker Ball Right
3. Push the Tracker Ball to the right.
The following message appears on the LCD:
Push Tracker Ball Down
4. Push the Tracker Ball towards you.
The following message appears on the LCD:
Push Tracker Ball Up
5. Push the Tracker Ball away from you.
The following message appears on the LCD:
Release Tracker Ball
6. Release the Tracker Ball.
Calibration is complete.
Displaying Calibration Values
1. Use the number buttons to enter 34, then press
Calibrate.
Information similar to the following will appear
on the LCD:
LD2 R00 UD6 D9D
10 10 10 10
2. Press
LCD Clear to refresh the LCD.
Selecting LCD Language
The TOUCH TRACKER supports a number of different
languages including:
•English •Italian
•French •Portuguese
•German •Spanish
To change the language of prompts appearing on
the LCD, do the following:
1. Use the number buttons to enter 35, then press
Calibrate.
2. Use the
Next button to scroll through the
available languages.
3. Press
Ack (Enter) when the correct language
appears on the LCD.
The TOUCH TRACKER resets. All future messages on
the LCD will appear in the selected language.
Displaying the Firmware
Version
1. Use the number buttons to enter 100, then
press F1.
The firmware information appears on the LCD.
F 0701-2490-0100
E 0701-2491-0100
The information appearing after the “F” is the
Flash version.
The information appearing after the “E” is the
EEPROM version.
2. Press
LCD Clear to refresh the LCD.