American Dynamics ADC 660P User manual












Hi-Res. B/W camera
instruction manual
ADC 660N
ADC 660P
Version: Rev. A
Part Number 8200-0839-01

Notice
To prevent fire or shock hazard, do not expose the unit to rain or
moisture.
The symbol is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Warning
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
Equipment Modification Caution
Equipment changes or modifications not expressly approved by Sensormatic Electronics
Corporation, the party responsible for FCC compliance, could void the user’s authority to
operate the equipment and could create a hazardous condition.
This class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
WARNING

Caution
This installation should be made by a qualified service person and should conform to all
local and national electrical and mechanical codes.

PRECAUTIONS
1. Do not attempt to disassemble the camera.
In order to prevent electric shock, do not remove screws or cover. There are
no user-serviceable parts inside.
2. Do not expose the camera to rain or moisture, or try to operate it in wet
areas.
Take immediate action if the camera becomes wet. Turn the power off and refer
servicing to qualified service personnel. Moisture can damage the camera and
also create a danger of electric shock.
3. Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty. In a case where the dirt is
hard to remove, use a mild detergent and wipe gently.
4. Never point the camera toward the sun.
Whether the camera is used outdoors or not, never point it toward the sun.
Use caution when operating the camera in the vicinity of spot lights or other
bright lights and light reflecting objects.
5. Do not operate the camera beyond its temperature, humidity or power source
ratings.
Do not use the camera in an extreme environment where high temperature or
high humidity exists. Use the camera under conditions where temperatures are
between 14° F~122° F (-10° C~+50° C) and humidity is below 85%.
6. Use a 24V AC / 12V DC class 2 LPS supply only.

Hi-Res. B/W camera instruction manual
ADC 660N and ADC 660P
_________________________________
5
Copyright
©2007 Sensormatic Electronics Corporation.
Product specifications subject to change without notice. Certain product names
mentioned herein may be trade names and/or registered trademarks of other
companies.
Customer Service
Thank you for using American Dynamics products. We support our products through
an extensive worldwide network of dealers. The dealer through whom you originally
purchased this product is your point of contact if you need service or support. Our
dealers are empowered to provide the very best in customer service and support.
Dealers should contact American Dynamics at [phone] or [phone] or
on the Web at www.americandynamics.net.

Hi-Res. B/W camera instruction manual
ADC 660N and ADC 660P
_________________________________
6
I. CONNECTORS AND CONTROLS .................................................................................. 7
1. VIDEO OUTPUT CONNECTOR (BNC)................................................................................ 7
2. POWER INPUT CONNECTOR (SCREW TERMINAL) ............................................................... 7
3. AUTO IRIS LENS CONNECTOR FOR VIDEO DRIVE LENS .................................................... 8
4. AUTO IRIS LENS CONNECTOR FOR DC DRIVE LENS .......................................................... 8
5. BLC (BACKLIGHT COMPENSATION) ON/OFF SWITCH ...................................................... 9
6. ALC/ELC SELECT SWITCH (EE/ELC IS ON; ALC/AI IS OFF) ....................................... 10
7. AGC ON/OFF SWITCH ............................................................................................... 11
8. INT/LL SWITCH (LL IS ON; INT IS OFF) ...................................................................... 11
9. FL ON SWITCH (FLICKERLESS ON/OFF)...................................................................... 11
10. V-PHASE ADJUSTMENT POTENTIOMETER....................................................................... 11
11. ALC LEVEL ADJUSTMENT POTENTIOMETER FOR DC DRIVE LENS.................................... 13
12. POWER INDICATOR LED ............................................................................................... 14
13. BACKFOCUS ADJUSTMENT SCREW ................................................................................ 14
14. C MOUNT ADAPTOR RING ............................................................................................ 16
15. CCD DUST PROTECTIVE CAP ....................................................................................... 16
16. CAMERA MOUNT HOLE ................................................................................................. 16
17. CAMERA MOUNT BASE ................................................................................................. 16
II. EXAMPLES OF CONNECTIONS .................................................................................. 17
1. SIMPLEST:ONE MONITOR SYSTEM WITH ONE CAMERA ..................................................... 17
2. ONE MONITOR SYSTEM WITH TWO OR MORE CAMERAS..................................................... 17
III. DIMENSIONS................................................................................................................. 18
IV. SPECIFICATIONS ......................................................................................................... 19

Hi-Res. B/W camera instruction manual
ADC 660N and ADC 660P
_________________________________
7
I. CONNECTORS AND CONTROLS
1. Video Output Connector (BNC)
1.0V p-p/75Ω composite video signal is provided at this connector.
2. Power Input Connector (screw terminal)

Hi-Res. B/W camera instruction manual
ADC 660N and ADC 660P
_________________________________
8
This terminal accepts 12 VDC or 24 VAC.
Power Requirement: Maximum 200 mA (12 VDC), Maximum 100 mA (24 VAC).
Recommended Power Supply: Minimum 500 mA (12 VDC); Minimum 300 mA (24 VAC).
Caution:
Use a 24V AC / 12V DC class 2 LPS supply only.
3. Auto Iris Lens Connector for VIDEO Drive Lens
This connector supplies 9 VDC power and video signal, without sync, for video-drive
type Auto Iris lens.
When using a VIDEO drive lens, the ALC/ELC DIP #1 must be set to the ALC (OFF)
position.
4. Auto Iris Lens Connector for DC Drive Lens
This connector supplies the control signals to the DC drive Auto Iris lens.
PIN Signal
1
2
3
GROUND
POWER SUPPLY (9 VDC, 40mA)
VIDEO OUTPUT (0.7Vp-p without sync)

Hi-Res. B/W camera instruction manual
ADC 660N and ADC 660P
_________________________________
9
When using a DC drive lens, the ALC/ELC DIP #1 must be set to the ALC (OFF)
position.
5. BLC (Backlight Compensation) ON/OFF Switch
If the subject you wish to view is too dim because of a bright background, set the
BLC DIP switch #2 to ON to compensate for the bright background.
With BLC on, the background brightness may saturate in some cases. This
function may not operate properly if the object is too small compared to the area
of the background. This function can be used with either the linear shutter (EE or
ELC mode) or an Auto Iris lens (AI lens or ALC mode).
WITH BLC OFF WITH BLC ON

Hi-Res. B/W camera instruction manual
ADC 660N and ADC 660P
_________________________________
10
6. ALC/ELC Select Switch (EE/ELC is ON; ALC/AI is OFF)
This switch is used to select EE (electronic exposure)/ELC (electronic light control)
mode or AI (Auto Iris lens)/ALC (automatic light control) mode. DIP switch 1 is set
to ON for EE/ELC and OFF for AI/ALC.
In the EE/ELC mode, a continuously variable electronic shutter is employed to
automatically control the exposure time of the CCD image sensor according to the
incoming light level. With this mode selected, a fixed or manual iris lens can be
used instead of an Auto Iris lens. In the AI/ALC mode, the CCD shutter speed is
fixed to 1/60 (1/50) sec, and the incoming light level is controlled by the Auto Iris
lens. To use a video-drive type or the DC-drive type of Auto Iris lens, set this
switch to the ALC position.
Cautions
 Under bright lighting conditions such as outdoors, use an Auto Iris lens
because the EE/ELC control range is not wide enough under these
conditions.
 Under certain unique lighting conditions, the following phenomena may
appear:
 Strong smear and/or blooming on highlighted objects such as spotlights
or windows.
 Noticeable flicker in the picture and/or color rendition variations. To
avoid this, use an Auto Iris lens.
 When operating in EE/ELC mode with manual iris lens, the depth of field of
the image may be less than that obtained by using an AI/ALC lens. Depth
of field varies inversely with the iris opening. Thus, using this camera in
EE/ELC mode with the manual iris lens fully opened may result in less depth
of field and the distant objects in a picture may be seen out of focus.
 Fixed iris or manual iris lenses may be used with the linear shutter (EE/ELC
mode) where the scene brightness varies over a limited range.
 Do not use the EE/ELC mode when an Auto Iris lens is installed.