American Sportworks 200 SERIES User manual

PAGE 1
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
TABLE OF CONTENTS
SUBJECT PAGE
I - General Information and Safety Table of Contents--------------------------------------------------------------- 1
Warranty Information------------------------------------------------------------- 2
Emissions Control System Warranty ------------------------------------------------- 2
Vehicle Records ---------------------------------------------------------------- 3
Foreword --------------------------------------------------------------------- 4
Important Safety Information-------------------------------------------------- 4 –11
Warnings and Cautions ------------------------------------------------------ 4 –7
Some Words About Safety --------------------------------------------------- 8 –11
Safety Labels ----------------------------------------------------------- 8 –9
Qualifications for Users ------------------------------------------------- 10 –11
II –Vehicle Controls and Operation
Controls and Features ---------------------------------------------------- 12 –17
Vehicle Features and Locations --------------------------------------------------- 18
Are You Ready To Drive? ------------------------------------------------- 19 –20
Is Your Vehicle Ready to Drive? ------------------------------------------- 20 –23
Starting Instructions ------------------------------------------------------- 23 –24
Safe Driving Precautions -------------------------------------------------- 24 –26
III - Unit Service Tire/Wheel Replacement ------------------------------------------------------ 26
Front End Alignment --------------------------------------------------------- 27
Front and Rear Shock Adjustment ------------------------------------------------- 27
Fuse Replacement ------------------------------------------------------------ 27
General Lubrication ----------------------------------------------------------- 28
Engine Lubrication ------------------------------------------------------------ 28
Air Filter ------------------------------------------------------------------ 29
Intake Cleaning - Engine Cooling Fan -------------------------------------------- 29
Spark Plug ---------------------------------------------------------------- 29
Chain Lubrication and Adjustment ----------------------------------------------- 30
Shifter Adjustment ---------------------------------------------------------- 30
Carburetor ---------------------------------------------------------------- 31
General Cleaning ------------------------------------------------------------ 31
Storage Instruction ----------------------------------------------------------- 31
Fastener Torque Chart -------------------------------------------------------- 32
Accessories ----------------------------------------------------------------- 32
Replacement Parts and Service -------------------------------------------------- 32
IV - Specifications Dimensions ------------------------------------------------------------------ 33
Engine ---------------------------------------------------------------------- 33
Capacities ------------------------------------------------------------------ 33
Periodic Check and Service Table ---------------------------------------------- 34
Electrical Schematic --------------------------------------------------------- 35

PAGE 2
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
EMISSION CONTROL SYSTEM WARRANTY STATEMENT
The Emission Control System Warranty on yourAmerican Sportworks vehicle is covered by Geason Enterprises, LLC dba Geason Powersports
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The U.S. Environmental Protection Agency and Geason Enterprises, LLC dba Geason Powersports (hereinafter “Geason Powersports”) are pleased to explain
the emission control system warranty on your 2012 and later Off-Road ATV. New off-road motor vehicles must be designed, built and equipped to meet U.S.
EPA Federal anti-smog standards. Geason Powersports must warrant the emission control system on your vehicle for 5000km, or at least 30 months,
whichever comes first, provided that there has been no abuse, neglect or improper maintenance of your vehicle. This ATV was designed to meet the emission
standards for 10,000km, or 5 years, whichever comes first.
Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, catalytic converter and engine computer, if it
is equipped. Also included may be hoses, belts, connectors and other emission-related assemblies.
Where a warrantable condition exists, Geason Powersports will repair your vehicle at no cost to you, including diagnosis, parts and labor.
If an emission-related part on your vehicle is defective, the parts will be repaired or replaced by Geason Powersports. This is your emission control system
DEFECTS WARRANTY.
NOTICE! Use of any Geason Powersports vehicle in any type of competitive event completely and absolutely voids this and all other warranties offered by
Geason Powersports.
OWNER’S WARRANTY RESPONSIBILITIES
As the vehicle owner, you are responsible for the performance of the required maintenance listed in your owner’s manual. Geason Powersports recommends
that you maintain a record of all receipts covering maintenance on your vehicle, but Geason Powersports cannot deny a warranty claim solely for the lack of
receipts or for your failure to ensure the performance of all scheduled maintenance.
You are responsible for presenting your vehicle to the Geason Powersports dealer as soon as a problemexists. The warranty repairs should be completed ina
reasonable amount of time, not to exceed 30 days.
As the owner, you should be aware that Geason Powersports may deny your warranty coverage if your vehicle, or a part, has failed due to abuse, neglect,
improper maintenance or unapproved modifications.
If you use your vehicle in any type of competitive event, this warranty is immediately and completely void.
If you have any questions regarding your warranty rights and responsibilities, you should contact Geason Enterprises, LLC dba Geason Powersports, 1200
Lakeside Parkway #325, Flower Mound, TX 75028, Phone [phone] or the U.S. Environmental Protection Agency, 2000 Traverwood Drive, Ann Arbor, MI
48105.
WARRANTY COVERAGE
Geason Enterprises, LLC dba Geason Powersports (hereinafter “Geason Powersports”) warrants that each new 2012 and later Geason Powersports
off-road vehicle:
A. is designed, built, and equipped so as to conform at the time of initial retail purchase with all applicable regulations of the United States
Environmental Protection Agency, and;
B. is free from defects in material and workmanship which cause such vehicle to fail to confirm with applicable regulations of the United
States Environmental ProtectionAgency for the periods specified above.
I. Coverage: Warranty defects shall be remedied during customary business hours at anyauthorized Geason Powersports dealer located
within the United States of America in compliance with the Clean Air Act and applicable regulations of the United States Environmental
ProtectionAgency. Any part of parts replaced under this warranty shall become the property of Geason Powersports.
II. Limitations: This Emission Control System Warranty shall not cover any of the following:
a. Repair or replacement as a result of
i. accident
ii. misuse
iii. repairs improperly performed or replacements improperly installed,
iv. use of replacement parts or accessories not conforming to specifications set forth by Geason Powersports, which
adversely affect performance and/or
v. use in competitive racing or related events
b. Inspections, replacement of parts and other services and adjustments required for required maintenance
c. Any vehicle equipped with an odometer or hour meter on which the odometer mileage or hourmeter reading has beenchanged
so that actual mileage cannot be readily determined.
III. Limited Liability
a. The liability of Geason Powersports under this Emission Control System Warranty is limited solely to the remedying of defects
in material or workmanship by an authorized Geason Powersports dealer at its place of business during customary business
hours. This warranty does not cover inconvenience or loss of use of the vehicle or transportation of the vehicle to or from the
Geason Powersports dealer. Geason Powersports shall not be liable for any other expenses, loss or damage, whether direct,
incidental, consequential, or exemplary arising in connection with the sale or use of or inability to use the Geason Powersports
vehicle for any purpose. Some states do not allow the exclusion or limitation of any incidental or consequential damages, so
the above limitations may not apply to you.
b. No express emission control system warranty is given by Geason Powersports, except as specifically set forth herein. Any
emission control system warranty implied by law, including any warranty of merchantability or fitness for a particular purpose, is
limited to the express emission control system warranty terms stated in the warranty. The foregoing statements of warranty
are exclusive and in lieu of all other remedies. Some states do not allow limitations on how long an implied warranty lasts, so
the above limitations may not apply to you.
c. No dealer is authorized to modify this Limited Emission Control System Warranty issues by Geason Powersports.
IV. Legal Rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
V. This warranty is in addition to the Geason Powersports limited vehicle warranty.
VI. Additional Information: Any replacement part that is equivalent in performance and durability may be used in the performance of any
maintenance or repairs. However, Geason Powersports are not liable for these parts. The owner is responsible for the performance of
all required maintenance. Such maintenance may be performed at a service establishment or by an individual. The warranty period
begins on the date theATV is delivered to an ultimate purchaser.

PAGE 3
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
AMERICAN SPORTWORKS LIMITED WARRANTY
American SportWorks (hereinafter referred to as “ASW”), hereby warrants to the original purchaser, that the
frame components of new ASW vehicles will be free from defects in material and workmanship. The period
of warranty is (1) year from date of purchase for the component parts (except as noted below), and (1) year
from the date of purchase for the frame and (1) year from the date of purchase for the engine. ASW, if
notified of a defect in material or workmanship during the period of warranty, will repair or replace, at its option,
defective parts at no charge, other than the reasonable cost for the transportation of the component(s).
ASW will also agree to pay reasonable charges for labor, if necessary, to perform a warranty repair. Proof of
Purchase must be provided to an approved ASW service center before any warranty work is performed.
The original purchaser must operate the vehicle and maintain the vehicle in accordance with the instructions
provided in the Operator’s Manual, the supplements hereto, and labels affixed to the vehicle. Additionally,
within (10) days of the discovery of an alleged defect, the original purchaser must contact ASW’s Customer
Service Department at 1-800-643-7332, 4404 Engle Ridge Drive, Fort Wayne, IN 46804 or via the internet at
www.amsportworks.com. The repair or replacement of any part or parts under this Limited Warranty shall
not extend the term of the warranty beyond the original term as set forth above.
General Exclusions: This limited warranty does not cover component failure or damage caused by any of the
following: abnormal strain or stress, neglect; abuse; improper assembly of components which were supplied
in the factory sealed carton after the vehicle left ASW; improper maintenance, improper use of the vehicle,
including, but not limited to racing, jumping, stunt driving, overloading, or any other uses prohibited by the
Operator’s Manual. Additionally, this warranty does not cover component failure or damage to vehicles which
are leased, rented, or used at a concession track.
Specific Exclusions: This limited warranty does not apply to components, which are subject to normal wear
and tear and natural discoloration of material due to ultraviolet light. These items include, but are not limited
to, the tires, brakes, throttle, shift and brake cables, drive belt, the torque converter system, chain, seat, lights,
fasteners, decals, or cosmetic body panels. Downtime, pick-up and delivery charges are not covered by this
warranty.
ASW MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIMITATIONS SPECIFIED IN THE
WARRANTY ABOVE ARE HEREBY DISCLAIMED BY ASW AND EXCLUDED FROM THIS WARRANTY. ADDITIONALLY, THIS
WARRANTY EXCLUDES ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OF USE.
SOME STATES DO NOT ALLOW A MANUFACTURER TO EXCLUDE OR LIMIT INCIDENTAL OR CONSEQUENTIAL DAMAGES AND,
THEREFORE, THE ABOVE EXCLUSION MAY NOTAPPLY TO YOU.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY WILL LAST; IT IS POSSIBLE THAT THE
ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER LEGALRIGHTS, WHICH VARY, FROM STATE TO STATE.
MY VEHICLE IDENTIFICATION NUMBER
Record the Vehicle Identification Number (VIN) and Model number of your American SportWorks vehicle
below for service and insurance records. The VIN is hard tagged on the vehicle frame under the bed.
VIN: L6KUA00__ __ __ __ __ __ __ __ __ __ Model: __ __200

PAGE 4
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
FOREWORD
Congratulations on the purchase of your ASW Vehicle. Before operating this vehicle, the owner and each
operator must understand that, unless specifically equipped and labeled as a street legal Low Speed Vehicle
(LSV), this vehicle was not designed or manufactured to meet specifications for use on public roads, streets,
highways and thoroughfares The owner, operator(s) and passenger(s) must read and understand all the
instructions for proper assembly and safe operation, as well as the instructions concerning the engine and all
other portions of the vehicle as described and illustrated in this manual and on the included safety video.
This unit is not designed for children, and is not a toy.
Be sure to follow the recommended maintenance schedule and service your vehicle accordingly.
Preventative maintenance is extremely important to the longevity of your vehicle. NOTE: A new vehicle
requires an engine break in period of 5 hours, whereby the engine oil MUST be changed (See
SERVICE section)
First time drivers are urged to seek instruction from a dealer or qualified instructor before and during the initial
use of this unit. It is also recommended to practice in a large open area to become familiar with the
operation of the vehicle.
We hope you will have a fun, safe experience with our products and thank you again for choosing an
American Sportworks Vehicle.
* IMPORTANT SAFETY INFORMATION *
WARNINGS AND CAUTIONS
This is the safety alert symbol. When you see this symbol on your machine or in this
manual, be alert to the potential for personal injury.
Read and follow all instructions in this Owner’s/Operator’s manual and any
accompanying supplements before attempting to operate this vehicle. Make sure to
view the Operations and Safety video.
NOTE: Use of the word “NOTE” will alert you to key information or instructions.
Indicates a potential hazard which may result in personal injury or damage to the machine.
Indicates a potential hazard that could result in severe personal injury or death.
WARNING
CAUTION

PAGE 5
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
1. Exhaust fumes are toxic.
a. California Proposition 65 WARNING: Gasoline engine exhaust from this machine contains
chemicals known to the State of California to cause cancer, birth defects, or other
reproductive harm. The engine exhaust contains carbon monoxide, which is a tasteless,
odorless, poisonous gas.
b. NEVER operate this vehicle indoors or in an enclosed area without adequate ventilation
2. NEVER adjust, repair, or clean the machine while it is in motion.
3. Check tire pressure before each use.
a. Prior to operating the vehicle check and adjust tire pressure to the proper operating pressure
as indicated on the sidewall of each tire or in the specification section of this manual. A tire
pressure gauge is required to obtain accurate readings.
4. Safety decals must be replaced if they become unreadable or detached from the vehicle.
a. If decals are unreadable or missing, warning of potential hazards or safety requirements may
be lacking.
5. The safe operation of this vehicle is dependent upon the operator’s ability to exercise proper
judgment.
a. Operator and passenger must not be too small or too large for controlled operation.
b. Operator and passenger must be of sufficient age, understanding, mental capacity, and
physical capacity to safely operate the vehicle.
c. Vehicle should only be operated after mature, supervised instruction and sufficient practice in
an un-congested area.
6. This vehicle may have been supplied to you completely assembled. To prevent injury or death
read and follow the assembly instructions to make sure the unit was assembled properly.
7. It is strongly recommended that Operator and any passengers wear a properly fitting
motorcycle helmet approved by agencies such as the Department of Transportation (DOT),
Safety Helmet Council of America (SHCA), or Snell Memorial Foundation (SNELL).
a. Most accident fatalities are due to head injuries.
b. Operator (and any passenger) should also wear face shields or goggles, boots, gloves and
other appropriate protective clothing.
(See MACHINE OPERATION)
8. Vehicle modification or removal of original equipment or safety decals can render the
machine unsafe for operation.
9. Long hair, loose clothes, or jewelry can get caught in moving parts below and behind the seat
or surrounding environment.
a. Remove or tie back anything loose that can reach below and behind the seat before riding.
10. Keep guards in place at all times.
a. Prevent accidental contact by the operator or service personnel while the vehicle is running.
b. The guards over the brake, clutch or torque converter, axle and drive sprockets also help
prevent mud and debris from coming in contact with those items.
11. Be sure the passenger restraint system (i.e. Seat Belt) is properly adjusted and fastened at all
times during operation.
a. If the passenger restraint system is not properly used by the operator and/or passengers,
loss of control and possible personal injury and/or vehicle damage can occur.
WARNING

PAGE 6
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
12. When there is no passenger in the vehicle, the passenger seatbelt must be securely fastened
within the vehicle.
a. If the passenger restraint system is not properly used by the operator and/or passenger, loss
of control and possible personal injury and/or vehicle damage can occur.
13. NEVER start the engine without checking to see that the throttle control is in idle position.
14. NEVER tamper with, alter, or change the vehicle engine governor settings.
a. The governor, as set by the engine manufacturer, limits maximum engine speed and protects
the engine from damage.
b. Excessive engine speed is potentially dangerous to operator, passengers, bystanders, and
engine.
15. All screws, nuts, and bolts must be properly tightened to make sure the vehicle is in safe
operating condition.
16. NEVER place hands, feet, or any body parts or clothing near the engine, wheels, chain, and
other rotating parts of the vehicle while riding or running the engine.
a. Use caution in performing required maintenance on or near operating engine.
b. Use caution after the engine has been running, since the engine and other drive components
may be extremely hot.
17. Check fuel supply before each use.
a. NEVER fill fuel tank while the engine is running or hot.
b. DO NOT overfill tank.
c. ALWAYS allow at least ½” of expansion space at the top of tank.
d. There should not be any fuel in the filler neck.
e. Replace cap tightly to prevent a fuel spillage fire hazard.
NOTE: Always use an original gas cap or OEM replacement.
-NEVER fill fuel tank while the vehicle is inside a building.
-After filling the tank, move the vehicle at least ten feet before attempting to start the engine.
18. ALWAYS use extreme caution when starting the engine.
a. Hot engine, muffler, or drive components can burn on contact.
19. ALWAYS SLOW DOWN when turning.
a. High-speed turning can cause loss of control and/or possible operator injury.
b. Turning on a slope increases the risk of rollover.
c. Practice operation is required to coordinate turning skill.
d. Failure to operate this vehicle at a safe speed while turning can result in a strong possibility of
severe personal injury.
20. Washing or operating the vehicle in freezing temperatures can result in water freezing in the
throttle cable conduit and/or on the throttle mechanism.
a. This may result in the throttle sticking which can cause the engine to continue to run and
result in loss of control.
21. When making repairs or adjustments to the vehicle, the spark plug wire MUST be
disconnected and kept away from the spark plug to prevent accidental starting.
a. When working on, around, or restarting engine, use extreme caution to avoid contact with the
muffler, cylinder head or any potentially hot area on or around the engine.
b. Ensure that all guards are in place prior to starting the engine.
WARNING

PAGE 7
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
22. Operating the vehicle in conditions where water, mud, snow, dirt, sand, or other debris can get
into the throttle cable conduit and/or on the throttle mechanism can cause binding of the
cable and/or the throttle mechanism.
a. This may result in the throttle sticking which can cause the engine to continue to run and
result in loss of control.
23. Assembly, maintenance, and/or repair of this vehicle should only be performed by designated
dealers or authorized small engine centers (for engine repairs) so that no unsafe conditions or
modifications are made.
24. Wet, slippery, rough, or sloped terrain is potentially dangerous and may result in injury if
proper caution is not observed.
a. ALWAYS SLOW DOWN
b. Operator must use mature judgment, skill, and experience to choose a speed suitable for
terrain and riding conditions in protecting operator and any bystanders.
c. Operator must use mature judgment, skill and experience in choosing suitable terrain for
individual operational capabilities.
25. Prevailing-torque type locknuts must be replaced with new after the old locknuts have been
removed.
a. Replace with the same type of locknut to make sure they function properly. Refer to the
maintenance section for more information on locknuts.
26. NEVER operate the vehicle while under the influence of alcohol, drugs, or medication of any
kind.
a. Such operation is dangerous to yourself and/or others.
27. Read and keep all supplied printed material.
a. Supplements to this Operator’s Manual contain updated information relative to your specific
vehicle model. It is important to keep all of these documents for reference.
1. During vehicle storage, keep it in a place where gasoline fumes will not reach an open flame,
spark, or other source of ignition. For long term storage:
a. Disconnect the battery
b. Drain fuel tank and carburetor bowl in a well-ventilated, open, cool area.
c. Engine must be allowed to cool before storage in any enclosure.
d. NEVER store the vehicle in close proximity to appliances such as hot water heaters or
furnaces.
2. Brush Bars assembled to this vehicle are for decorative purpose and limited brush protection.
a. Brush Bars were not designed for roll over or to restrict all brush or tree branches from
protruding into operator/passenger compartment.
3. If the vehicle should start making unusual noise or vibrating abnormally, the engine should be
stopped and the spark plug wire disconnected. The vehicle should then be checked for
damage. Excessive noise or vibration is generally a warning of loose or worn parts.
CAUTION
WARNING

PAGE 8
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
SOME WORDS ABOUT SAFETY
The following pages present important information and recommendations to help you drive your vehicle
safely. Please read through these pages thoroughly and view the Safety DVD that was included with
your unit.
SAFETY LABELS
The following labels have been applied to your unit and should be considered as permanent parts of the
vehicle. If a label should come off, become hard to read, or become damaged, contact your dealer or
American SportWorks Customer Service department for warning label replacements.

PAGE 9
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3

PAGE 10
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
QUALIFICATIONS FOR USERS
This vehicle is recommended for use by operator and passenger with a minimum age of sixteen years.
Vehicles are intended for use by operators who meet the physical and cognitive capabilities set out by the
manufacturer in the material provided with the vehicle.
Consumer Responsibility for Safe Use and
Maintenance of a Vehicle
1. Vehicle shall not be modified from the manufacturer’s original design and configuration.
2. Vehicle shall not be used to perform racing, stunt riding, jumps, spinouts, donuts, or other maneuvers as
they may cause loss of control. As such, these activities are likely to result in possible injury to the
operator, bystanders, or both.
3. Prior to each use, the operator shall perform the preoperational checks specified by the manufacturer,
and further verify:
a. Smooth throttle operation and positive return of the throttle linkage to a closed throttle position when
released;
b. That the throttle cable and linkages operate properly and the throttle cable or other linkages be
adjusted properly;
c. That the steering linkage is adjusted and operates smoothly;
d. That the engine stop switch is properly functioning;
e. That all guards originally supplied by the manufacturer are in proper place in serviceable condition;
f. That engine idle speed is below the point of clutch or torque converter engagement;
g. That the gas tank is in good condition and the proper gas cap is fastened securely;
h. That the braking system is functioning properly;
i. That all safety labels are in place, legible and understood;
j. That any and all axle guards, chain guards, torque converter covers, or other covers or guards
supplied by the manufacturer are in place and in serviceable condition;
k. That tires are in good condition, inflated properly, and have sufficient tread remaining; and
l. That all fasteners are in place and tightened securely.
4. Vehicle engines shall not be started unless the operator is seated in proper position for vehicle operations
and the brake fully engaged.
5. Long hair, loose clothes, or jewelry can get caught in moving parts below the seat or surrounding
environment. Remove or tie back anything loose that can reach below or behind the seat before riding.
6. Vehicles shall only be fueled by an operator knowledgeable with regard to proper fueling techniques.
7. All operators or riders shall be knowledgeable, capable, and have the cognitive capacity to operate the
vehicle safely, including those items specified in 1 through 6.
8. Vehicle operators and passengers shall adhere to all manufacturer’s recommendations and instructions,
as well as comply with all laws and ordinances, as well as:
a. Operators shall stay seated with both hands on the steering wheel and both feet in the vehicle at all
times, whether moving or stationary, unless the vehicle is stopped completely and the engine has
been shut off.
b. Passengers shall remain seated with arms and legs inside the vehicle at all times during vehicle
operation.

PAGE 11
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
c. Shall observe minimum age restrictions.
d. Shall not ride the Vehicle if long hair, loose clothes, or jewelry reach below or behind the seat.
e. Shall not allow smoking in vehicle.
f. Persons under the influence of drugs, alcohol, or intoxicants shall not supervise, operate, or ride in a
vehicle.
Vehicles shall operate only on a surface or terrain recommended by the vehicle’s manufacturer.
g. Vehicles shall not be operated on roads, streets, highways, or any other location where road vehicles
are intended to travel unless specifically designed and designated for such use.
h. Vehicles shall be operated only with adequate lighting and under conditions of suitable visibility.
9. Persons with the following conditions shall not ride in or operate a Vehicle:
a. Those with heart conditions
b. Pregnant women
c. Persons with head, back, or neck ailments, or prior surgeries to those areas of the body.
d. Persons with any mental or physical conditions, which may make them susceptible to injury or impair
their physical dexterity or mental capabilities to recognize, understand, and perform all of the safety
instructions, and be able to assume the hazards inherent in vehicle use.
10. Vehicle shall not be used to:
a. Transport a passenger, or passengers, except in the seating area(s) provided.
b. Transport materials or equipment in excess of the rated cargo capacity;
11. Vehicle operators always shall use appropriate protective clothing, including but not limited to a
motorcycle type helmet and eye protection, with appropriate certification, and any other equipment
recommended by the vehicle manufacturer including gloves, footwear, long sleeve shirts, and long pants.
12. No operator or other person shall contact any portion of the engine, wheels, or drive train for any purpose
including maintenance until the engine has been turned off and allowed to cool, and the vehicle is in a
stable and stationary position.
13. Passenger restraints must be used in accordance with, and limited to, the manufacturer’s guidelines.
14. Vehicle components shall be maintained and repaired in accordance with the manufacturer’s
specifications and utilizing only the manufacturer’s authorized replacement parts with installation
performed by designated dealers or other skilled persons.
Long hair, loose clothes, or jewelry can get caught in moving parts below and behind the seat
or surrounding environment. Remove or tie back anything loose that can reach below or
behind the seat before riding.
WARNING

PAGE 12
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
Every time, prior to starting the engine, check the throttle assembly to ensure that when the
pedal is pushed all the way forward the assembly is working smoothly and returns to idle
when released. Do not operate this unit if pedal or engine throttle linkage fail to return to the
idle position. If unable to correct the problem through lubrication, adjustment or replacement
of worn parts, contact your dealer for assistance.
II - VEHICLE CONTROLS AND OPERATION
Controls and Features
A. Throttle
The foot pedal on the right is the throttle (See Figure), to control the speed of the vehicle. As the engine
speed increases above idle, the clutch automatically engages and moves the vehicle forward. To disengage
the clutch at any time, allow the throttle to return to the idle position.
Do not attempt to start or operate the engine until completely familiar with the location and use
of each control necessary to operate this vehicle. The operator must know how to stop this
machine before starting and driving it.
WARNING
WARNING
STEERING WHEEL
CUP HOLDER
KEYED IGNITION
SWITCH –CARGO LIGHT
SWITCH –HEAD LIGHT
12V POWER
OUTLET
PARK BRAKE
LEVER
THROTTLE PEDAL
BRAKE PEDAL
MANUAL CHOKE (IF SO EQUIPPED)

PAGE 13
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
B. Brake
The brake is controlled by the foot pedal on the left (See Figure). Applying pressure to the pedal draws the
brake pads against the brake discs at the wheels and slows or stops the vehicle.
C. Parking Brake
This vehicle is equipped with a parking brake system. The parking brake lever can be found in
front of the passenger seat just under the dash. To apply the brake, simply depress the brake
pedal and pull back on the parking brake lever, locking it into position. To disengage, depress
the pedal, push the thumb button located at the top of the lever and return to its original position towards the
front of the vehicle.
C. Lights This vehicle is equipped with front running lights, a rear running/brake lamp, and a rear facing cargo
light. To turn the running lights on, flip the lower switch located next to the keyed ignition on the
dashboard of the unit. The cargo light can be turned on by flipping the upper switch located next
to the keyed ignition. (See Figure) The rear brake light will activate automatically when the
brake pedal is depressed.
D. Power Outlet
This vehicle also is equipped with a 12V, 15amp power outlet for plugging in accessory items, and comes
standard with a rubber cap. Do not exceed the maximum amperage rating of the plug.
E. Keyed Ignition Switch
For added security, this unit is equipped with a keyed ignition switch. The keyed ignition
will only start the engine when brake pedal is depressed. As an added feature, all lights
are turned off when the key switch is in the “OFF” position. Refer to page 25 for specific
starting instructions.
F. Manual Choke
Some units come equipped with a manual choke in lieu of an automatic electric choke. The
choke is used to assist in cold engine starting. The choke is “ON” when the knob is pulled out
completely and “OFF” when the knob is pushed in completely. Refer to page 25 for specific
starting instructions.
G. Rear View Mirror
The unit is equipped with a rear view mirror. Adjust the mirror such that objects can be easily seen while
sitting in correct driving position.
H. Seat Adjustment
The unit is equipped with an adjustable seat. To adjust, lift the levers just in front of the seat bottom and
move the seat either forward or backward. Release the levers at the desired seat location, ensuring that
they both snap back into place to lock the seat.
Never operate this vehicle when the seat is not securely locked into position. Serious injury
or death could occur due to loss of control. Always make seat adjustments with the vehicle
fully stopped and the engine shut off.
WARNING

PAGE 14
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
I. Occupant Restraints
This vehicle is equipped with automotive style 3 point retracting seat belts. Insert the metal
tongue into the buckle until it is securely attached. Final adjustments should be made with the
plastic tension stop such that the belt is against the shoulder and chest with no excess slack.
This vehicle is also equipped with a passenger grab bar located on the dash directly in front of
the passenger seat.
J. Under-seat Storage
This vehicle is equipped with a storage area under the seat. To access the storage area, seat belts must be
unlatched and the seat must be cleared of riders or objects. Provision for a padlock or combination lock (not
included) is available on the seat latch handle. To open the storage area, remove any lock and press the
lever down. With the lever depressed, lift the rear of the seat and rotate forward to reveal the storage space.
NOTE: The under-seat storage area is not watertight. Items that need to stay dry should be bagged or
placed in a watertight container within the storage area.
K. Gear Selection
This vehicle is equipped with a Forward / Neutral / Reverse transmission. To shift gears, always bring
the vehicle to a complete stop and let the engine RPM stabilize to the idle level. With the brake applied,
move the shift lever to the desired gear and gently depress the throttle pedal.
Failure to fully latch the seat in the closed position could result in seat movement while driving
and cause serious injury or death. Always ensure that the seat is fully latched before driving.
WARNING
Damage to the vehicle will occur if the unit is shifted into a different gear while the vehicle is
still in motion. ALWAYS bring the vehicle to a complete stop before selecting a different gear.
CAUTION
LATCH HANDLE
UNDER-SEAT
STORAGE
SEAT ADJUSTMENT LATCH

PAGE 15
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
L. Tool Holders
This vehicle is equipped with standard side mounted tool holders for safely carrying garden
tools such as rakes, shovels, etc… The tool holders are rubber coated and spring loaded to
keep the tool from bouncing or rattling while the unit is in motion. Shorter tools may be loaded
into the tool holders provided the handle is long enough to protrude through the middle loop,
and provided the head of the tool bottoms out against the rotating loop. The holders are
designed to rotate in the COUNTERCLOCKWISE direction only. To insert tool:
1) Rotate the tool horizontally and slide the handle through the loop from the RIGHT side
2) Rotate the tool vertically in a COUNTERCLOCKWISE direction
3) Slide the tool downward through the second loop and onto lower tool rest
Step 1 Step 2 Step 3
M. Cargo Dump Bed –250lb MAX LOAD
This vehicle is equipped with a manual rear dump cargo bed. Release levers are located on
both the driver and passenger sides of the vehicle just forward and above the rear wheels.
Loose cargo should be secured with a cargo net, or proper cargo straps to prevent shifting during
transport. This bed is NOT designed to transport people or animals and should be used for
hauling cargo only. Prior to dumping any loads, the parking brake should be applied and the
keyed ignition turned to the “OFF” position. To dump the bed, unlatch and lower the tailgate. Standing to
the side of the unit, pull the release lever upwards then manually tilt the bed to dump the load. After dumping,
the bed and tailgate should be securely latched.
Ensure that all tools are correctly and securely loaded into the tool holders before driving.
Failure to secure the tool could cause damage to the unit, and cause serious injury or death.
WARNING
Long tools will extend past the overhead brush bars, increasing the overall height of the
vehicle. Damage to the tool, unit or to surrounding structures will occur when driving into
low overhead clearances.
CAUTION

PAGE 16
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
N. TAILGATE LATCH AND REMOVAL
The tailgate on this unit has been fitted with cam over style
latches. The latches are designed to secure the tailgate
to the bed, while minimizing rattles. To unlatch the
tailgate, depress the latch lock and pull the hasp away from
the tailgate. Once unlatched, the tailgate will swing freely
towards the rear bumper. To latch, simply close the gate
securely against the bed tube and lock the wire hasp over
the bed latch.
Removal of the tailgate requires a 10 and 12mm wrench
and removal of the hinge bolts. If the tailgate is removed, temporarily install the hinge bolts into the tailgate
to prevent loss of the fasteners.
O. DRAWBAR HITCH - 500lb MAX LOAD (Rolling)
This vehicle may be equipped with a drawbar style hitch for
towing light utility karts, non-ground engaging lawn
equipment, and various attachments. Pull behind mower
decks are not approved for use with this vehicle because
the partial throttle / slow travel speed required causes
continuous CVT clutch slippage and pre-mature drive train
wear. This drawbar is NOT designed to accept equipment
with hitch ball type tongues. Drawbar hitch is designed for
75lb maximum tongue weight.
Ensure that towed items fall within the listed load ratings AND are approved devices.
Exceeding the rated load, or using unapproved devices, will cause damage to both the
drawbar hitch and engine drive-train that is not covered by warranty.
Do not lean over the bed while releasing the bed latch. Loads shifted towards the tailgate
may cause the front of the bed to suddenly raise when unlatched causing serious injury.
WARNING
Ensure that the bed is securely latched before driving the unit. Failure to properly latch bed
may result in damage to cargo, or to the unit.
CAUTION
CAUTION
Latch Lock
Bed Latch

PAGE 17
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
F. Manual Fuel Valve
Some units come equipped with a manual fuel valve in lieu of an engine vacuum
operated valve. The manual valve provides the added feature of a “reserve” position
which provides access to a reserve fuel supply allowing additional driving range to get to
a fuel filling station should the main fuel supply be used completely.
OFF: With the fuel valve in the OFF position, fuel
cannot flow from the tank to the carburetor. Turn the
fuel valve OFF whenever the unit is not in use or
during transport.
Note: If the unit is being transported from one location to another, i.e. in the bed of a
pick-up truck or on a trailer, turn the fuel valve OFF to prevent excess fuel flow into the
carburetor. This can cause engine “flooding” and difficulty starting.
ON: With the fuel valve in the ON position, fuel will
flow from the main fuel supply to the carburetor.
RESERVE: With the fuel valve in the RESERVE
position, fuel will flow from the reserve fuel supply
to the carburetor. Use this only when the main
fuel supply is gone. Proceed directly to refill the
tank with fuel once switching to the RESERVE
position.
Note: Return the fuel valve to the ON position after refueling. If the valve is left in the
RESERVE position you may run out of fuel and have no reserve.

PAGE 18
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
VEHICLE FEATURES AND LOCATIONS
THROTTLE PEDAL
BRAKE PEDAL
PARKING BRAKE
SHIFT LEVER
STEERING WHEEL
REAR VIEW MIRROR
TOOL HOLDER
CUP HOLDER
3PT SAFETY BELTS
OVERHEAD BRUSH BARS
PASSENGER GRAB BAR
BUMPER
HIP GUARD
ADJUSTABLE SEAT
RUNNING LIGHTS
UNDER-SEAT STORAGE
FUEL TANK
BED LATCH
MANUAL DUMP
CARGO BED
FUEL VALVE

PAGE 19
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
ARE YOU READY TO DRIVE?
Before each drive, you need to make sure that you and your vehicle are both ready to drive. To help get you
prepared, this section discusses how to evaluate your driving readiness, what items you should check on your
vehicle, and adjustments to make for your comfort, convenience, or safety. Before you drive your vehicle for
the first time, we urge you to:
- Read this owner’s manual and the labels on your vehicle carefully.
- Make sure you understand all the safety messages.
- Know how to operate all the controls.
- View and understand the included safety DVD
Protective Apparel
Although complete protection is not possible, wearing proper gear can reduce the chance of injury should you
have an accident. The following suggestions will help you choose the proper protective gear.
Helmet and Eye Protection
Your helmet is your most important piece of protective gear because it offers the best protection against
head injuries. A helmet should fit your head comfortably and securely.
Open-face helmets offer some protection, but a full-face helmet offers more. Regardless of the style,
look for a D.O.T. (Department of Transportation) or Snell Memorial Foundation (SNELL) sticker on any
helmet you buy. Always wear a face shield or goggles to protect your eyes and help your vision.
Additional Driving Gear
In addition to a helmet and eye protection, we also recommend:
-Sturdy boots to help protect feet, ankles, and lower legs.
-Gloves to help protect your hands
Driver Training
Developing your driving skills is an ongoing process. Even if you are and experienced driver, take time
Operating this vehicle without wearing an approved motorcycle helmet, eye protection, and
protective clothing could increase your chances of head and/or eye injury, and the possibility
of death in the event of a severe accident.
Always wear an approved motorcycle helmet that fits properly and wear eye protection
(goggles or face shield), gloves, boots, long-sleeved shirt or jacket and long pants.
WARNING

PAGE 20
OWNER’S/OPERATOR’S MANUAL – 200 SERIES PART NUMBER 14833R3
to become familiar with the controls and how the vehicle handles. Practice driving in a safe, open area
to develop your skills. Do not drive on rough terrain until you get accustomed to the vehicle controls
and feel comfortable with its size and weight.
No Alcohol or Drugs
Alcohol, drugs and vehicles don't mix. Even a small amount of alcohol can impair your ability to operate
a vehicle safely. Likewise, drugs, even if prescribed by a physician, can be dangerous while operating a
vehicle. Consult your doctor to be sure it is safe to operate a vehicle after taking medication.
IS YOUR VEHICLE READY TO DRIVE?
Before each drive, it is important to inspect your vehicle and make sure any problems you find are corrected.
A pre-drive inspection is a must, not only for safety, but because having a breakdown, or even a flat tire, can
be a major inconvenience.
If your vehicle has overturned or has been involved in a collision, do not drive it until your vehicle has been
inspected by your dealer. There may be damage or other problems that you cannot see.
Operating this vehicle without your seat belt could cause you to be thrown from the unit,
causing serious injury or death.
WARNING
Operating this vehicle after consuming alcohol or drugs can seriously affect your judgment,
cause you to react more slowly, affect your balance and perception, and could result in
serious injury or death. Never consume alcohol or drugs before or while operating this
vehicle.
WARNING
Improperly maintaining this vehicle or failing to correct a problem before driving can cause an
accident resulting in serious injury or death.
Always perform a pre-drive inspection before every drive and correct any problems.
WARNING